EN25B16-100FC datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > storage> storage> EN25B16-100FC

EN25B16-100FC: DescriptionFlash Memory,; Categorystorage storage; File Size474KB，37 Pages; ManufacturerESMT; Websitehttp://www.esmt.com.tw/; Elite Semiconductor Memory Technology Inc. (ESMT) is a professional IC design company founded by Dr. Hu Zhao in June 1998. Its headquarters is located in Hsinchu Science Park, Taiwan. The company's main business includes research, development, manufacturing, sales and related technical services of IC products. It was listed on the Taiwan Stock Exchange in March 2002.

Download Datasheet Parametric View All

EN25B16-100FC Overview

Flash Memory,

EN25B16-100FC Parametric

Parameter Name	Attribute value
package instruction	,
Reach Compliance Code	unknown
Base Number Matches	1

EN25B16-100FC Preview

Download Datasheet

View All

EN25B16

16 Mbit Serial Flash Memory with Boot and Parameter Sectors

FEATURES

•

Single power supply operation

- Full voltage range: 2.7-3.6 volt

•

16 M-bit Serial Flash

- 16 M-bit/2048 K-byte/8192 pages

- 256 bytes per programmable page

•

High performance

- 100MHz clock rate

•

Low power consumption

- 5 mA typical active current

- 1

μA

typical power down current

•

Flexible Sector Architecture:

- Two 4-Kbyte, one 8-Kbyte, one 16-Kbyte,one

32-Kbyte, and thirty one 64-Kbyte sectors

•

Software and Hardware Write Protection:

- Write Protect all or portion of memory via

software

- Enable/Disable protection with WP# pin

•

High performance program/erase speed

Byte program time: 7µs typical

Page program time: 1.5ms typical

Sector erase time: 300 to 800ms typical

Chip erase time: 18 Seconds typical

•

Minimum 100K endurance cycle

•

Package Options

- 8 pins SOP 200mil body width

- 8 contact VDFN

- 8 pins PDIP

- 16 pin SOP 300mil body width

- All Pb-free packages are RoHS compliant

•

Commercial and industrial temperature

Range

GENERAL DESCRIPTION

The EN25B16 is a 16M-bit (2048K-byte) Serial Flash memory, with advanced write protection

mechanisms, accessed by a high speed SPI-compatible bus. The memory can be programmed 1 to

256 bytes at a time, using the Page Program instruction.

The EN25B16 has thirty six sectors including thirty one sectors of 64KB, one sector of 32KB, one sector

of 16KB, one sector of 8KB and two sectors of 4KB. This device is designed to allow either single Sector

at a time or full chip erase operation. The EN25B16 can protect boot code stored in the small sectors for

either bottom or top boot configurations. The device can sustain a minimum of 100K program/erase cycles

on each sector.

This Data Sheet may be revised by subsequent versions

or modifications due to changes in technical specifications.

Rev. E, Issue Date: 2007/06/07

EN25B16

SIGNAL DESCRIPTION

Serial Data Input (DI)

The SPI Serial Data Input (DI) pin provides a means for instructions, addresses and data to be

serially written to (shifted into) the device. Data is latched on the rising edge of the Serial Clock (CLK)

input pin.

Serial Data Output (DO)

The SPI Serial Data Output (DO) pin provides a means for data and status to be serially read from (shifted

out of) the device. Data is shifted out on the falling edge of the Serial Clock (CLK) input pin.

Serial Clock (CLK)

The SPI Serial Clock Input (CLK) pin provides the timing for serial input and output operations. ("See SPI

Mode")

Chip Select (CS#)

The SPI Chip Select (CS#) pin enables and disables device operation. When CS# is high the device is

deselected and the Serial Data Output (DO) pin is at high impedance. When deselected, the devices

power consumption will be at standby levels unless an internal erase, program or status register cycle is

in progress. When CS# is brought low the device will be selected, power consumption will increase to

active levels and instructions can be written to and data read from the device. After power-up, CS# must

transition from high to low before a new instruction will be accepted.

Hold (HOLD#)

The HOLD pin allows the device to be paused while it is actively selected. When HOLD is brought low,

while CS# is low, the DO pin will be at high impedance and signals on the DI and CLK pins will be ignored

(don’t care). The hold function can be useful when multiple devices are sharing the same SPI signals.

Write Protect (WP#)

The Write Protect (WP#) pin can be used to prevent the Status Register from being written. Used in

conjunction with the Status Register’s Block Protect (BP0, BP1and BP2) bits and Status Register Protect

(SRP) bits, a portion or the entire memory array can be hardware protected.

Table 1. PIN Names

Symbol

CLK

CS#

WP#

HOLD#

Vcc

Vss

Pin Name

Serial Clock Input

Serial Data Input

Serial Data Output

Chip Enable

Write Protect

Hold Input

Supply Voltage (2.7-3.6V)

Ground

This Data Sheet may be revised by subsequent versions

or modifications due to changes in technical specifications.

Rev. E, Issue Date: 2007/06/07

Recommended Resources

Four-channel infrared remote control remote transmitter circuit

Thyristor overcurrent protection circuit

Multifunctional color changing light circuit

Temperature alarm with adjustable threshold

Micropower Temperature Measurement Circuit

12V, 5A regulated power supply composed of LM340K integrated voltage regulator

HTS221 MakeCode extension (driver): The MakeCode extension for the HTS221 temperature and humidity sensor allows you to use the HTS221 in a graphical way. The extension is ported from the MicroPython driver , retaining the oneshot mode ...; dcexpert MEMS sensors

Can sensorless drive completely replace sensory drive?: When selecting BLDC driver chips, I see that many new ones are sensorless. Can this type of sensorless type completely replace sensor-based chips? What are the advantages and disadvantages of each typ...; littleshrimp Motor Drive Control（Motor Control）

Motor drive development communication 3: Software component description: Continue from the previous post: https://en.eeworld.com/bbs/thread-1155646-1-1.htmlDescription of the software part:In addition to writing and debugging their own software, software engineers are also...; 安驱技术_孙大卫 Motor Drive Control（Motor Control）

MP3302DJ chip drives 640*480 LCD screen heating problem: The circuit is designed according to the manual. The PB14 pin is set as the enable pin, the input level is 3.3V, and LEDK and LEDA are connected to the LCD driver pins. When the power is turned on and...; nibofys LED Zone

Is the baud rate for communication between microcontrollers set in advance? Or calculated? Also, why does the crystal oscillator have 11.0592...: Is the baud rate for communication between microcontrollers set in advance? Or calculated? Also, why does the crystal oscillator havea value of 11.0592M? Common frequencies are 4M, 8M, 12M, 16M, and 2...; QWE4562009 MCU

GigaDevice GD32L233 Review Summary: // Wonderful demo 1.Some music 2.Super Mario Run 3.Timer + DMA driver WS2812B 4.Different buttons --ADC keyboard// Review Tips 1. Development board introductionFirst look at GD32L233C-STARTDevelopment...; EEWORLD社区 GD32 MCU

Popular Components