To all our customers
Regarding the change of names mentioned in the document, such as Mitsubishi
Electric and Mitsubishi XX, to Renesas Technology Corp.
The semiconductor operations of Hitachi and Mitsubishi Electric were transferred to Renesas
Technology Corporation on April 1st 2003. These operations include microcomputer, logic, analog
and discrete devices, and memory chips other than DRAMs (flash memory, SRAMs etc.)
Accordingly, although Mitsubishi Electric, Mitsubishi Electric Corporation, Mitsubishi
Semiconductors, and other Mitsubishi brand names are mentioned in the document, these names
have in fact all been changed to Renesas Technology Corp. Thank you for your understanding.
Except for our corporate trademark, logo and corporate statement, no changes whatsoever have been
made to the contents of the document, and these changes do not constitute any alteration to the
contents of the document itself.
Note : Mitsubishi Electric will continue the business operations of high frequency & optical devices
and power devices.
Renesas Technology Corp.
Customer Support Dept.
April 1, 2003
MITSUBISHI 8-BIT SINGLE-CHIP MICROCOMPUTER
740 FAMILY / 38000 SERIES
3800
Group
User’s Manual
Keep safety first in your circuit designs!
Mitsubishi Electric Corporation puts the maximum effort into making
semiconductor products better and more reliable, but there is always the
possibility that trouble may occur with them. Trouble with semiconductors
may lead to personal injury, fire or property damage. Remember to give due
consideration to safety when making your circuit designs, with appropriate
measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of
non-flammable material or (iii) prevention against any malfunction or mishap.
Notes regarding these materials
These materials are intended as a reference to assist our customers in the
selection of the Mitsubishi semiconductor product best suited to the
customer’s application; they do not convey any license under any
intellectual property rights, or any other rights, belonging to Mitsubishi
Electric Corporation or a third party.
Mitsubishi Electric Corporation assumes no responsibility for any damage,
or infringement of any third-party’s rights, originating in the use of any
product data, diagrams, charts or circuit application examples contained in
these materials.
All information contained in these materials, including product data,
diagrams and charts, represent information on products at the time of
publication of these materials, and are subject to change by Mitsubishi
Electric Corporation without notice due to product improvements or other
reasons. It is therefore recommended that customers contact Mitsubishi
Electric Corporation or an authorized Mitsubishi Semiconductor product
distributor for the latest product information before purchasing a product
listed herein.
Mitsubishi Electric Corporation semiconductors are not designed or
manufactured for use in a device or system that is used under
circumstances in which human life is potentially at stake. Please contact
Mitsubishi Electric Corporation or an authorized Mitsubishi Semiconductor
product distributor when considering the use of a product contained herein
for any specific purposes, such as apparatus or systems for transportation,
vehicular, medical, aerospace, nuclear, or undersea repeater use.
The prior written approval of Mitsubishi Electric Corporation is necessary to
reprint or reproduce in whole or in part these materials.
If these products or technologies are subject to the Japanese export
control restrictions, they must be exported under a license from the
Japanese government and cannot be imported into a country other than
the approved destination.
Any diversion or reexport contrary to the export control laws and
regulations of Japan and/or the country of destination is prohibited.
Please contact Mitsubishi Electric Corporation or an authorized Mitsubishi
Semiconductor product distributor for further details on these materials or
the products contained therein.
Preface
This user’s manual describes Mitsubishi’s CMOS 8-
bit microcomputers 3800 Group.
After reading this manual, the user should have a
through knowledge of the functions and features of
the 3800 Group, and should be able to fully utilize
the product. The manual starts with specifications
and ends with application examples.
For details of software, refer to the “SERIES MELPS
740 <SOFTWARE> USER’S MANUAL.”
For details of development support tools, refer to the
“DEVELOPMENT SUPPORT TOOLS FOR MICRO-
COMPUTERS” data book.
BEFORE USING THIS USER’S MANUAL
This user’s manual consists of the following three chapters. Refer to the chapter appropriate to your conditions, such
as hardware design or software development. Chapter 3 also includes necessary information for systems development.
Be sure to refer to this chapter.
1. Organization
q
CHAPTER 1 HARDWARE
This chapter describes features of the microcomputer and operation of each peripheral function.
q
CHAPTER 2 APPLICATION
This chapter describes usage and application examples of peripheral functions, based mainly on setting examples
of related registers.
q
CHAPTER 3 APPENDIX
This chapter includes necessary information for systems development using the microcomputer, electric
characteristics, a list of registers, the masking confirmation (mask ROM version), and mark specifications which
are to be submitted when ordering.
2. Structure of register
The figure of each register structure describes its functions, contents at reset, and attributes as follows :
(Note 2)
Bits
b7 b6 b5 b4 b3 b2 b1 b0
0
Bit attributes
(Note 1)
Contents immediately after reset release
CPU mode register (CPUM) [Address : 3B
16
]
B
0
1
2
3
4
5
6
7
Stack page selection bit
Name
Processor mode bits
b1 b0
Function
0 0 : Single-chip mode
01:
1 0 : Not available
11:
0 : 0 page
1 : 1 page
At reset
R W
0
0
0
0
0
1
T
T
Nothing arranged for these bits. These are write disabled
bits. When these bits are read out, the contents are “0.”
Fix this bit to “0.”
Main clock (X
IN
-X
OUT
) stop bit
Internal system clock selection bit
0 : Operating
1 : Stopped
0 : X
IN
-X
OUT
selected
1 : X
CIN
-X
COUT
selected
!
!
: Bit in which nothing is arranged
: Bit that is not used for control of the corresponding function
Note 1. Contents immediately after reset release
0••••••“0” at reset release
1••••••“1” at reset release
Undefined••••••Undefined or reset release
T
••••••Contents determined by option at reset release
Note 2. Bit attributes••••••The attributes of control register bits are classified into 3 bytes : read-only, write-only
and read and write. In the figure, these attributes are represented as follows :
R••••••Read
••••••Read enabled
!••••••Read
disabled
W••••••Write
••••••Write enabled
!
••••••Write disabled
京公网安备 11010802033920号
EEWORLD
