EEWORLDEEWORLDEEWORLD

Part Number

Search

QS8BLF-03-1501-J

Description
Array/Network Resistor, Bussed, 0.75W, 100V, 5% +/-Tol, 25ppm/Cel, Surface Mount, 1519, QSOP, ROHS COMPLIANT
CategoryPassive components    The resistor   
File Size365KB,4 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Environmental Compliance
Download Datasheet Parametric View All

QS8BLF-03-1501-J Overview

Array/Network Resistor, Bussed, 0.75W, 100V, 5% +/-Tol, 25ppm/Cel, Surface Mount, 1519, QSOP, ROHS COMPLIANT

QS8BLF-03-1501-J Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerTT Electronics plc
package instruction, 1519
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresPRECISION
Component power consumption0.05 W
The first element resistor1500 Ω
JESD-609 codee3
Manufacturer's serial numberQSOP
Installation featuresSURFACE MOUNT
Network TypeBUSSED
Number of components15
Number of functions1
Number of terminals16
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package shapeRECTANGULAR PACKAGE
method of packingTR; TUBE
Rated power dissipation(P)0.75 W
Rated temperature70 °C
Resistor typeARRAY/NETWORK RESISTOR
size code1519
surface mountYES
Temperature Coefficient25 ppm/°C
Temperature coefficient tracking5 ppm/°C
Terminal surfaceMatte Tin (Sn)
Terminal shapeGULL WING
Tolerance5%
Operating Voltage100 V
Base Number Matches1
Surface Mount QSOP
Resistor Networks
QSOP Series
Reliable, no internal cavity
High resistor density - .025" lead spacing
Standard JEDEC 16, 20, and 24 pin packages
Ultra-stable TaNSil
®
resistors on silicon substrate
RoHS compliant and Sn/Pb terminations available
IRC’s TaNSil
®
QSOP resistor networks are the perfect solution for high volume applications that demand a
small wiring board footprint. The 0.025" lead spacing provides higher lead density, increased component
count, lower resistor cost, and high reliability.
The tantalum nitride film system on silicon provides precision tolerance, exceptional TCR tracking, low cost
and miniature package. Excellent performance in harsh, humid environments is a trademark of IRC’s
self-passivating TaNSil
®
resistor film.
The QSOP series is ideally suited for the latest surface mount assembly techniques and each lead can be
100% visually inspected. The compliant gull wing leads relieve thermal expansion and contraction stresses
created by soldering and temperature excursions.
For applications requiring high performance resistor networks in a low cost, surface mount package, specify
IRC QSOP resistor networks.
Electrical Data
Resistance Range
Absolute Tolerance
Ratio Tolerance to R1
Absolute TCR
Tracking TCR
Element Power Rating @ 70°C
Isolated Schematic
Bussed Schematic
Package Power Rating @ 70°C
Rated Operating Voltage
______
(not to exceed
P x R)
Operating Temperature
Noise
100mW
50mW
16-Pin
20-Pin
24-Pin
750mW
1.0W
1.0W
10 to 250KΩ
To ±0.1%
To ±0.05%
To ±25ppm/°C
To ±5ppm/°C
Environmental Data
Test Per
MIL-PRF-83401
Typical
Delta R
Max Delta
R
Thermal Shock
±0.02%
±0.1%
Power Conditioning
±0.03%
±0.1%
High Temperature Exposure
±0.03%
±0.05%
Short-time Overload
±0.02%
±0.05%
100 Volts
-55°C to
+125°C
<-30dB
Low Temperature Storage
±0.03%
±0.05%
Life
±0.05%
±2.0%
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
A subsidiary of
TT electronics plc
QSOP Series Issue January 2009 Sheet 1 of 4
AD test of Qinheng CH583
After downloading the program via USB, I cut off the power, connected the serial port to the development board, and the power indicator light was slightly on, but the program did not run. When I opene...
kangkls Domestic Chip Exchange
What problems will 485 bus level mismatch cause?
[i=s]This post was last edited by sfcsdc on 2021-5-12 17:54[/i]The 485 transceiver on one side is powered by 3.3V; The 485 transceiver on one side is powered by 5V;there is data loss during communicat...
sfcsdc Analog electronics
[Repost] Do you understand all this knowledge about inductors?
The current in the inductor cannot change suddenly. (After the voltage across the inductor is removed, the current will not disappear immediately, thus generating a reaction potential)Inductor is an e...
皇华Ameya360 Power technology
Please tell me a formula in LM5118
Given that the output voltage is 12V and the maximum input voltage is 42V, find the value of L1. According to BUCK MODE, L1=(12*(42-12))/(42*300000*1.2) The document says L1=28UH, but no matter how I ...
sky999 PCB Design
Thank you for your inquiry about maxim max14912
1. After drawing the schematic diagram and making the board, directly power on 24V. No 5V output is seen from V5M, that is, D17 light is not on, which means the chip is not working. 2 Is there any off...
guitianxia Analog electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号