The UT54ACS74 and the UT54ACTS74 contain two indepen-
dent D-type positive triggered flip-flops. A low level at the
Preset or Clear inputs sets or resets the outputs regardless of the
levels of the other inputs. When Preset and Clear are inactive
(high), data at the D input meeting the setup time requirement
is transferred to the outputs on the positive-going edge of the
clock pulse. Following the hold time interval, data at the D
input may be changed without affecting the levels at the outputs.
The devices are characterized over full military temperature
range of -55°C to +125°C.
FUNCTION TABLE
INPUTS
PRE
L
H
L
H
H
H
CLR
H
L
L
H
H
H
CLK
X
X
X
↑
↑
L
D
X
X
X
H
L
X
OUTPUT
Q
H
L
H
1
PINOUTS
14-Pin DIP
Top View
CLR1
D1
CLK1
PRE1
Q1
Q1
V
SS
1
2
3
4
5
6
7
14
13
12
11
10
9
8
V
DD
CLR2
D2
CLK2
PRE2
Q2
Q2
14-Lead Flatpack
Top View
CLR1
D1
CLK1
PRE1
Q1
Q1
V
SS
1
2
3
4
5
6
7
14
13
12
11
10
9
8
V
DD
CLR2
D2
CLK2
PRE2
Q2
Q2
LOGIC SYMBOL
PRE1
CLK1
D1
CLR1
PRE2
CLK2
D2
CLR2
(4)
(3)
(2)
(1)
(10)
(11)
(12)
(13)
(9)
(8)
Q2
Q2
S
C1
D1
R
(5)
(6)
Q1
Q1
Q
L
H
H
L
H
Q
o
1
H
L
Q
o
Note:
1. The output levels in this configuration are not guaranteed to meet the minimum
levels for V
OH
if the lows at preset and clear are near V
IL
maximum. In
addition, this configuration is nonstable; that is, it will not persist when either
preset or clear returns to its inactive (high) level.
Note:
1. Logic symbol in accordance with ANSI/IEEE standard 91-1984 and IEC
Publication 617-12.
1
LOGIC DIAGRAM
PRE
CLR
Q
CLK
Q
D
2
OPERATIONAL ENVIRONMENT
1
PARAMETER
Total Dose
SEU Threshold
2
SEL Threshold
Neutron Fluence
LIMIT
1.0E6
80
120
1.0E14
UNITS
rads(Si)
MeV-cm
2
/mg
MeV-cm
2
/mg
n/cm
2
Notes:
1. Logic will not latchup during radiation exposure within the limits defined in the table.
2. Device storage elements are immune to SEU affects.
ABSOLUTE MAXIMUM RATINGS
SYMBOL
V
DD
V
I/O
T
STG
T
J
T
LS
Θ
JC
I
I
P
D
PARAMETER
Supply voltage
Voltage any pin
Storage Temperature range
Maximum junction temperature
Lead temperature (soldering 5 seconds)
Thermal resistance junction to case
DC input current
Maximum power dissipation
LIMIT
-0.3 to 7.0
-.3 to V
DD
+.3
-65 to +150
+175
+300
20
±10
1
UNITS
V
V
°C
°C
°C
°C/W
mA
W
Note:
1. Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, functional operation of the device at
these or any other conditions beyond limits indicated in the operational sections is not recommended. Exposure to absolute maximum rating conditions for extended
periods may affect device reliability.
RECOMMENDED OPERATING CONDITIONS
SYMBOL
V
DD
V
IN
T
C
PARAMETER
Supply voltage
Input voltage any pin
Temperature range
LIMIT
4.5 to 5.5
0 to V
DD
-55 to + 125
UNITS
V
V
°C
3
DC ELECTRICAL CHARACTERISTICS
7
(V
DD
= 5.0V
±
10%; V
SS
= 0V
6
, -55°C < T
C
< +125°C); Unless otherwise noted, Tc is per the temperature range ordered.
SYMBOL
V
IL
PARAMETER
Low-level input voltage
1
ACTS
ACS
High-level input voltage
1
ACTS
ACS
Input leakage current
ACTS/ACS
Low-level output voltage
3
ACTS
ACS
High-level output voltage
3
ACTS
ACS
Short-circuit output current
2 ,4
ACTS/ACS
Output current
10
(Sink)
I
OH
Output current
10
(Source)
P
total
I
DDQ
ΔI
DDQ
Power dissipation
2, 8, 9
Quiescent Supply Current
Quiescent Supply Current Delta
ACTS
V
IN
= V
DD
or V
SS
I
OL
= 8.0mA
I
OL
= 100μA
I
OH
= -8.0mA
I
OH
= -100μA
V
O
= V
DD
and V
SS
V
IN
= V
DD
or V
SS
V
OL
= 0.4V
V
IN
= V
DD
or V
SS
V
OH
= V
DD
- 0.4V
C
L
= 50pF
V
DD
= 5.5V
For input under test
V
IN
= V
DD
- 2.1V
For all other inputs
V
IN
= V
DD
or V
SS
V
DD
= 5.5V
C
IN
C
OUT
Input capacitance
5
Output capacitance
5
ƒ
= 1MHz @ 0V
ƒ
= 1MHz @ 0V
15
15
pF
pF
1.9
10
1.6
mW/
MHz
μA
mA
-8
mA
.7V
DD
V
DD
- 0.25
-200
8
200
.5V
DD
.7V
DD
-1
1
CONDITION
MIN
MAX
0.8
.3V
DD
UNIT
V
V
IH
V
I
IN
V
OL
μA
0.40
0.25
V
V
OH
V
I
OS
I
OL
mA
mA
4
Notes:
1. Functional tests are conducted in accordance with MIL-STD-883 with the following input test conditions: V
IH
= V
IH
(min) + 20%, - 0%; V
IL
= V
IL
(max) + 0%, -
50%, as specified herein, for TTL, CMOS, or Schmitt compatible inputs. Devices may be tested using any input voltage within the above specified range, but are
guaranteed to V
IH
(min) and V
IL
(max).
2. Supplied as a design limit but not guaranteed or tested.
3. Per MIL-PRF-38535, for current density
≤
5.0E5 amps/cm
2
, the maximum product of load capacitance (per output buffer) times frequency should not exceed 3,765
pF/MHz.
4. Not more than one output may be shorted at a time for maximum duration of one second.
5. Capacitance measured for initial qualification and when design changes may affect the value. Capacitance is measured between the designated terminal and V
SS
at
a frequency of 1MHz and a signal amplitude of 50mV rms maximum.
6. Maximum allowable relative shift equals 50mV.
7. All specifications valid for radiation dose
≤
1E6 rads(Si).
8. Power does not include power contribution of any TTL output sink current.
9. Power dissipation specified per switching output.
10. This value is guaranteed based on characterization data, but not tested.
Zigbee 3.0 new features introduction - click to watch the video
E2E Chinese Forum engineer Alvin will explain the new features of Zigbee 3.0, as well as an introduction to network access and the Zigbe...
[size=4]Tomorrow is the winter solstice. Do you eat dumplings or glutinous rice balls? Chinese traditional festivals are always accompanied by delicious food. But besides delicious food, what other cu...
[i=s]This post was last edited by pomin on 2022-10-16 20:46[/i] > ESP32-S2-Kaluga-1 development board communicates with MQTT server## Competition history posts - [[2022 Digi-Key Innovation Design Comp...
It has been almost a year since I came to EEWORLD. After posting today, I saw that it was the 2000th post, so I posted a message to record it.Last post:Thanks to the EEWORLD forum, I have gained a lot...
This small board was just released in June and July 2019. It has 128 NVIDIA CUDA and quad-core CortexA57. It can run a large number of CUDA (or CPU)-based artificial intelligence and image processing ...
introduction
As the level of automobile intelligence increases, the intelligent functions and entertainment attributes of automobiles have become the key directions for OEMs to creat...[Details]
Beijing Baidu Netcom Technology Co., Ltd. recently added a number of new patent information, one of which is related to autonomous driving, named "Vehicle Charging Method, Device, Electronic Device a...[Details]
Recently, the "2019-2020 China Charging Infrastructure Development Annual Report" (hereinafter referred to as the "Report") jointly compiled by the National Energy Administration and the China Elec...[Details]
0 Introduction
With the advancement of modern automotive electronic technology, traditional parts and assemblies in automobiles are also developing towards mechatronics. The large number of...[Details]
There are two single-phase capacitor motors with the same problem, one is a dual-capacitor motor and the other is a single-capacitor motor. The two motors have the same problem, that is, when start...[Details]
To simplify the task of drawing power from a battery or USB cable, Linear Technology offers several devices. These devices seamlessly manage the power flow between the AC adapter, USB cable and Li...[Details]
Oscilloscopes are very familiar to electronic engineers. They can be used for ripple testing, checking frequency, checking signal quality, measuring rise time, fall time and overshoot, parallel bus d...[Details]
As a new light source, in recent years, major companies and research institutions have been conducting research on LED
power supplies
and drive circuits. Unlike the electronic ballast o...[Details]
On April 11, Kunlun Wanwei issued an announcement stating that its wholly-owned subsidiary Kunlun Group Limited (hereinafter referred to as "Kunlun Group") intends to invest US$50 million of its own ...[Details]
Nippon Radio Co., Ltd. (Headquarters: Chuo-ku, Tokyo, Representative Director and President: Ryo Ogura) has developed a 600mA, 500kHz small package step-down switching regulator, the NJW1933, which i...[Details]
In the "Wireless Subsystem Synchronization" of GSM 05.10 clause, it is stipulated that: "The base station should use a single frequency source with an absolute accuracy better than 0.05 ppm (5×10-8) a...[Details]
1. The statement format of assembly language: label opcode (instruction mnemonic) operand; comment (label) (opcode) (operand) (comment) 2. Common pseudo-instructions a.EQU——Symbol name assignment ps...[Details]
I2S Bus Protocol 1. Overview of I2S Bus The acquisition, processing and transmission of audio data are important components of multimedia technology. Many digital audio systems have entered the con...[Details]
LEDs
are gradually replacing traditional cold cathode fluorescent lamps (
CCFL
)
in more and more applications
due to their advantages such as high
brightness
, long life, unifor...[Details]
On October 22, workers inspected the energy storage equipment area of the first phase of the 300 MW independent energy storage power station located in the Economic Development Zone of Longyao Count...[Details]
Wireless Connectivity
京公网安备 11010802033920号
EEWORLD
