EEWORLDEEWORLDEEWORLD

Part Number

Search

68780-316H

Description
Board Connector, 16 Contact(s), 2 Row(s), Male, Right Angle, 0.1 inch Pitch, Solder Terminal, Black Insulator, Receptacle
CategoryThe connector    The connector   
File Size285KB,3 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Download Datasheet Parametric View All

68780-316H Overview

Board Connector, 16 Contact(s), 2 Row(s), Male, Right Angle, 0.1 inch Pitch, Solder Terminal, Black Insulator, Receptacle

68780-316H Parametric

Parameter NameAttribute value
Is it lead-free?Contains lead
Is it Rohs certified?incompatible
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresBREAKAWAY TYPE
body width0.19 inch
subject depth0.273 inch
body length0.8 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationGOLD (50) OVER NICKEL (50)
Contact completed and terminatedTIN LEAD (150) OVER NICKEL (50)
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Dielectric withstand voltage1500VAC V
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialGLASS FILLED POLYCYCLOHEXYLENE TEREPHTHALLATE
JESD-609 codee0
Manufacturer's serial number68780
Plug contact pitch0.1 inch
Match contact row spacing0.1 inch
Installation methodRIGHT ANGLE
Installation typeBOARD
Number of connectorsONE
PCB row number2
Number of rows loaded2
Maximum operating temperature130 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
PCB contact row spacing2.54 mm
Plating thickness50u inch
Rated current (signal)3 A
GuidelineUL, CSA
reliabilityCOMMERCIAL
Terminal length0.039 inch
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts16
Base Number Matches1
Surface Wave Filters in RF Circuits
Radio frequency interference has always been the enemy of wireless communications, requiring designers to take drastic measures to keep it in check. With more and more frequency bands supported in eac...
btty038 RF/Wirelessly
Inductor selection issues
Hey guys, I have a question about inductor selection. As shown in the figure, after SENSOR_A_CTR3 (the charging circuit is not attached below), LC starts to oscillate, and SENSOR_A_IN directly enters ...
bingdongshijian Analog electronics
The story of motor drive integration
Just like every MOSFET needs a gate driver to switch it, there is always a driving force behind every motor. There are many ways to drive a motor, depending on the complexity and system cost, size and...
Jacktang Analogue and Mixed Signal
Generation and Operation of Discrete Signals in DSP
Experimental purposeReview and consolidate the generation and operation of discrete signals in digital signal processing.Learn and master the method of generating discrete signals with MATLAB.Learn an...
fish001 Microcontroller MCU
Selection of pull-up resistor value for common communication line
Hello everyone, I am a beginner. I am now learning to do a PCB board experiment. For the purpose of learning, I plan to use STM32 to connect multiple SPI devices at the same time. I have no problem co...
风轻轻 PCB Design
Constant current source + NMOS and PMOS (MCU control on and off) + LED solution consultation
Design principle and goal:The constant current source chip outputs constant current to the LED, and the single-chip microcomputer controls NMOS+PMOS to achieve LED high brightness for 200us, cycleProb...
BlueInvestment Analogue and Mixed Signal

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号