EEWORLDEEWORLDEEWORLD

Part Number

Search

HPS10Q-A5R-032

Description
HPS10/12/15 Series
File Size1MB,5 Pages
ManufacturerVertiv
Download Datasheet View All

HPS10Q-A5R-032 Overview

HPS10/12/15 Series

1000-6000 Watts
HPS10/12/15 Series
Electrical Specs
Input
Input voltage
Frequency
Inrush current
Efficiency
Power factor
Turn-on time
85-264 VAC*
47-440 Hz
40 A peak max.
85% typ @ full case load 230 VAC
0.99 typical meets EN61000-3-2
AC on 1.5 sec. typical, Inhibit /
Enable 100 ms typical
CISPR 22 EN55022 Level “B”
2 mA max @ 264 VAC @ 60Hz
(per module)
CISPR 22 EN55022 Level “B”
20 ms minimum
(independent of input VAC)
>5 ms early warning min. before
outputs lose regulation; Full cycle
ride thru (50 Hz)
Meets EN61000-3-2
Meets EN60950
Special Features
Integrated OR-ing diode
Remote Sense on Bulk output
Overload protection on all outputs
Active Inrush limiting
PFC to 0.99 typical EN61000-3-2
CISPR22, EN55022 Curve B
conducted/radiated EMI
EN61000 immunity standards
Optional 48 W fan voltage (12 V or 24 V)
Standard 5 V at 5 A standby voltage (3.3V option)
No minimum load
Overvoltage protection
Input OK signal and indicator LED
Inhibit/Enable
Remote Margin/Voltage Programming
Optional current monitor
Optional AC Line discrimination
Output Good signal and indicator LED
Temp good signal and indicator LED
Optional single wire digital temp monitor
2
Optional module I C interface
Optional Rack µController
Hot Plug
N+1 Redundant Standard
Optional fan fail signal
Module present signal
Optional short circut latch
EMI filter standard
Leakage current standard
Radiated EMI
Holdup time
AC OK
Harmonic distortion
Isolation
* see modules table on the next page
Output
Margining
Overall reg
Ripple
Dynamic response
Recovery time
Overcurrent protection
Short circuit protection
Overvoltage protection
Reverse voltage
protection
Thermal protection
Remote sense
Single wire parallel
DC OK
Minimum load
Standby voltage
Global Inhibit/Enable
±5% of nominal
1%
1% of Vout Pk-Pk limited to 20 MHz
2% with 25% load step
To within 1% in <300 µsec
105-120% of rated output current
Protected for continuous short
circuit. Recovery is automatic upon
removal of short
105-120% . Recycle AC input voltage
to reset OVP circuit
100% of rated output current
Main and Aux disabled when internal
temp exceeds safe operating range.
Up to 0.5 V total drop
Current share to within 10% of total
rated current
±5% of nominal
Not required
5 VDC @5A max. present whenever
AC input is applied (3.3 V @ 5A
optional)
Logic “0” standard logic “1” optional
Environmental & Safety
Operating temperature: -10°C to +50°C ambient,
derate output @ 2.5% per degree from 50°C to 70°C
Shock/Vibration: Mil-Hdbk 810E
Humidity: 95% non-condensing
Storage temperature: -40°C to +85°C
Temperature coefficient: 0.02% per °C
Cooling: Internal DC fan
MTBF (Calculated): 200 KHrs; 25°C, 200 VAC input,
nominal O/P voltage, full load
Safety:
UL / CSA
UL60950 3
rd
Ed and CSA C22.2 60950
TUV
EN60950
CB
Certificate and report
CE
Mark
152
Technical Support: (888) 41-ASTEC or (407) 241-2752
Americas: (760) 930-4600
Europe (UK) 44 (1384) 842-211
Asia (HK) 852-2437-9662
rev 08.25.04
Have you ever used MicroPython in your actual work?
As the title suggests, let me share some ideas, such as how to quickly prototype a product, debug a sensor, etc. In what scenarios do you think using MicroPython can improve work efficiency?...
zy459994202 MicroPython Open Source section
PICO CO2 Sensor Board
PICO works with the Sensirion SCD30 CO2 sensor to accurately detect a wide range of carbon dioxide levels in the atmosphere. It displays detailed information about the CO2 content (PPM) on the OLED di...
dcexpert MicroPython Open Source section
Pingtouge RVB2601 board-ADC acquisition and CSI
According to limited information, CH2601 has an internal ADC, but the pins are connected through the "ARDUINO" interface.The ADC driver of CH2601 is the CSI interface provided in the YOC development k...
bigbat Domestic Chip Exchange
The LIS2MDL array board welding of the magnetic nail navigation AGV car is completed
I received the board yesterday and the STM32F411 microcontroller today. It is quite convenient to use steel mesh for welding. I bought 10 sensors and 1 microcontroller. In order to save space, the mic...
littleshrimp ST Sensors & Low Power Wireless Technology Forum
The new evaluation information is here~~
Hello, everyone~ It's time for our evaluation information again~~ This week, the application list for the end of the event has been released, and some evaluation reports have been released, but not ma...
okhxyyo Special Edition for Assessment Centres
Use idle STM32 development boards and Freescale development boards
1. STM32F413ZH-Nucleo-144, 75 yuan, not including shipping2.KE02Z, 55 yuan, not including postageI want both, 120 yuan including postage, no cuts, thank you~~~...
MCU-huangjunwei Buy&Sell

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号