LF500RW
Series
Wide Input, 5W SMT
Single & Dual Output
DC/DC Converters
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Input
Key Features:
•
5W Output Power
•
Wide 2:1 Inputs
•
Miniature SMT Case
•
Tight Line/Load Regulation
•
1,500 VDC Isolation
•
-40ºC to +60ºC Operation
•
21 Standard Models
•
1.0 MH MTBF Minimum
•
Industry Standard Pin-Out
Parameter
Input Start Voltage
Reverse Polarity Input Current
Short Circuit Input Power
Input Filter
Conditions
12 VDC Input
24 VDC Input
48 VDC Input
Max.
9.0
18.0
36.0
1.0
1,000 3,000
π
(Pi) Filter (Meets EN55022 Class A)
Min.
Typ.
±0.5
±0.5
±0.1
±0.3
50
Max.
±1.0
±2.0
±0.3
±1.0
85
100
15
165
500
±6
±0.02
Min.
7.5
14.0
30.0
Typ.
8.0
16.0
33.0
Units
VDC
A
mW
Output
Parameter
Output Voltage Accuracy
Output Voltage Balance
Line Regulation
Load Regulation
Ripple & Noise (20 MHz) (Note 1)
Ripple & Noise (20 MHz)
Ripple & Noise (20 MHz)
Output Power Protection
Transient Response Time (Note 2)
Transient Response Deviation
Temperature Coefficient
Output Short Circuit
Conditions
Dual Output, Balanced Load
For Vin = Min to Max
Iout = 20% to 100%
Units
%
%
%
%
mV P - P
mV P - P
mV rms
%
µS
%
%/
º
C
115
25% Load Step Change
RoHS Compliant
140
250
±2
±0.01
Continuous
Conditions
60 Seconds
1,000 VDC
100 kHz, 1V
Min.
1,500
1,000
200
Conditions
Typ.
Max.
Units
VDC
MΩ
pF
kHz
Units
º
C
º
C
º
C
%
General
Parameter
Isolation Voltage
Isolation Resistance
Isolation Capacitance
Switching Frequency
650
260
750
350
Max.
+71
+90
+125
95
Environmental
Parameter
Operating Temperature Range
Operating Temperature Range
Storage Temperature Range
Cooling
Humidity
Min.
Typ.
Ambient
-40
+25
Case
-40
-40
Free Air Convection
RH, Non-condensing
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
T:
(781) 344-8226
F:
(781) 344-8481
E:
sales@micropowerdirect.com
W:
www.micropowerdirect.com
Physical
Case Size
Case Material
Weight
1.31 x 0.81 x 0.40 Inches (33.4 x 20.6 x 10.2 mm)
Non-Conductive Black Plastic (UL94-V0)
0.49 Oz (14g)
Conditions
MIL HDBK 217F, 25
º
C, Gnd Benign
Conditions
12 VDC Input
24 VDC Input
48 VDC Input
1.5 mm From Case For 10 Sec.
All Models
Min.
1.0
Min.
-0.7
-0.7
-0.7
Typ.
Max.
Units
MHours
Units
VDC
ºC
mW
Reliability Specifications
Parameter
MTBF
Absolute Maximum Ratings
Parameter
Input Voltage Surge (1 Sec)
Lead Temperature
Internal Power Dissipation
Typ.
Max.
25.0
50.0
100.0
260
2,500
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
Model Selection Guide
Model
Number
LF501RW
LF502RW
LF503RW
LF504RW
LF505RW
LF506RW
LF507RW
LF511RW
LF512RW
LF513RW
LF514RW
LF515RW
LF516RW
LF517RW
LF521RW
LF522RW
LF523RW
LF524RW
LF525RW
LF526RW
LF527RW
Input
Voltage (VDC)
Nominal
Range
12
9.0 - 18.0
12
9.0 - 18.0
12
9.0 - 18.0
12
9.0 - 18.0
12
9.0 - 18.0
12
9.0 - 18.0
12
9.0 - 18.0
24
18.0 - 36.0
24
18.0 - 36.0
24
18.0 - 36.0
24
18.0 - 36.0
24
18.0 - 36.0
24
18.0 - 36.0
24
18.0 - 36.0
48
36.0 - 75.0
48
36.0 - 75.0
48
36.0 - 75.0
48
36.0 - 75.0
48
36.0 - 75.0
48
36.0 - 75.0
48
36.0 - 75.0
Current (mA)
Full-Load
No-Load
434
20
521
20
502
20
502
20
521
20
501
20
503
20
212
5
254
5
245
5
245
5
5
254
245
5
246
5
106
3
127
3
123
3
122
3
127
3
122
3
123
3
Voltage
(VDC)
3.3
5.0
12.0
15.0
±5.0
±12.0
±15.0
3.3
5.0
12.0
15.0
±5.0
±12.0
±15.0
3.3
5.0
12.0
15.0
±5.0
±12.0
±15.0
Output
Current
(mA, Max)
1,200
1,000
417
333
±500
±208
±167
1,200
1,000
417
333
±500
±208
±167
1,200
1,000
417
333
±500
±208
±167
Reflected
Ripple Cur.
Current
(mA)
(mA, Min)
120.0
25
100.0
25
41.7
25
33.3
25
±50.0
25
±20.8
25
±16.7
25
120.0
15
100.0
15
41.7
15
33.3
15
±50.0
15
±20.8
15
±16.7
15
120.0
10
100.0
10
41.7
10
33.3
10
±50.0
10
±20.8
10
±16.7
10
Efficiency
(%, Typ)
76
80
83
83
80
83
83
78
82
85
85
82
85
85
78
82
85
85
82
85
85
Fuse Rating
Slow-Blow
(mA)
1,500
1,500
1,500
1,500
1,500
1,500
1,500
700
700
700
700
700
700
700
350
350
350
350
350
350
350
Notes:
1. When measuring output ripple, it is recommended that an external 0.47
µF
ceramic capacitor
be placed from the +Vout pin to the -Vout pin for single output units and from each output
to common for dual output units. For noise sensitive applications, the use of 3.3
µF
capacitors
will reduce the output ripple.
2. Transient recovery is measured to within a 1% error band for a load step change of 75% to
100%.
3. No-load operation will not damage these units, however, they may not meet specifications.
4. Dual output units may provide a 10V, 24V or 30V output. To do this, connect the load across
the positive (+Vout) and negative (-Vout) outputs and float the output common.
5. The converter should be connected to a low ac-impedance source. An input source with a
highly inductive impedance may affect the stability of the converter. In applications where
the converter output loading is high and input power is supplied over long lines, it may be
necessary to use a capacitor on the input to insure start-up. In this case, it is recommended
that a low ESR (ESR <1.0Ω at 100 kHz) capacitor be mounted close to the converter. For 12V
input units a 4.7
µF
is recommended, and for 24V & 48V units a 2.2
µF.
6. It is recommended that a fuse be used on the input of a power supply for protection. See the
table above for the correct rating.
Derating Curve
Remote ON/OFF
Parameter
Supply On
Supply Off
Standby Input Current
Control Common
Condition
Units
2.5 to 5.5 or Open Circuit
VDC
-0.7 to 0.8
VDC
10
mA
Referenced to Negative Input (-Vin)
Mechanical Dimensions
Remote ON/OFF Notes:
1. Maximum sink current at the
on/off pin (pin 1) during a
logic low is 300
µA.
2. Maximum allowable leakage
current of a switch connect-
ed to the on/off terminal
(Pin 1) at logic high (2.5V to
100V) is 200
µA.
Capacitive
Load
Single
Output
(Max)
680
µ
F
Dual
Output
(Max)
100
µ
F
Pin Connections
Pin
1
2
3
9
10
11
12
13
14
15
16
22
23
24
Single
Dual
On/Off On/Off
-Vin
-Vin
-Vin
-Vin
NC
Common
NC
NC
NC
-Vout
NC
NC
NC
NC
+Vout
+Vout
NC
NC
-Vout Common
+Vin
+Vin
+Vin
+Vin
NC
NC
Board Layout
NC:
No Connection
MicroPower Direct
www.micropowerdirect.com
•
292 Page Street Ste D Stoughton, MA 02072
TEL: (781) 344-8226
•
Notes:
dimens
•
All dimensions are typical in inches (mm)
•
Tolerance x
x.xx =
±
0.01 (
±
0.25)
•
Pin 1 is ma
marked by a “dot” or indentation
on the uni
unit
FAX: (781) 344-8481
•
E-Mail: sales@micropowerdirect.com
京公网安备 11010802033920号
EEWORLD
