Figure 7. Standard PECL Output Configuration Figure 8. Single Resistor Termination Scheme
Resistor values are typically 140 ohms for
3.3V operation.
Resistor values are typically 84 ohms for 2.5V
operation.
The VCC6 incorporates a standard PECL output scheme, which are un-terminated emitters as shown in Figure 7. There are numerous application notes on
terminating and interfacing PECL logic and the two most common methods are a single resistor to ground, Figure 8, and a pull-up/pull-down scheme as
shown in Figure 9. An AC coupling capacitor is optional, depending on the application and the input logic requirements of the next stage.
LVDS Application Diagrams
V
CC
LVDS
Driver
100
LVDS
Receiver
LVDS
Driver
100
Receiver
OUT+
OUT-
Figure 10 Standard LVDS
Output Configuration
Figure 11. LVDS to LVDS Connection, Internal 100ohm
Figure 12. LVDS to LVDS Connection
Some LVDS structures have an internal 100 ohm resistor on the
External 100ohm and AC blocking caps
input and do not need additional components.
Some input structures may not have an internal 100 ohm
resistor on the input and will need an external 100ohm
resistor for impedance matching. Also, the input may have
an internal DC bias which may not be compatible with
LVDS levels, AC blocking capacitors can be used.
One of the most important considerations is terminating the Output and Complementary Outputs equally. An unused output should not be left un-termi-
nated, and if one of the two outputs is left open it will result in excessive jitter on both. PC board layout must take this and 50 ohm impedance matching
into account. Load matching and power supply noise are the main contributors to jitter related problems.
Add the path of the header file in the makefile
INC_ESPCOMP += -I$(ESPCOMP)/esp_http_client/include
INC_ESPCOMP += -I$(ESPCOMP)/json/cJSON
INC_ESPCOMP += -I$(ESPCOMP)/nghttp/port/include
Then where sh...
Have you noticed the LPDSP32 audio codec inside RSL10? Does your project use this resource?
Today I accidentally noticed that there is an audio codec inside the RSL10
I wonder if ON has any voice reco...
蓝雨夜onsemi and Avnet IoT Innovation Design Competition
The step-down circuit shown in the figure
In normal operation, if there is a sudden power failure, that is, all three power supplies are gone, and then the power is turned on again
When the op amp U1 ...
Click to register
Live broadcast time
March 24, 10:00-11:30amLive Topic
Third Generation TI C2000 New Features Resource UpdateLive content
Compared with the second-generation C2000, the third-generati...
In practical applications, increasing radio frequency interference (RFI) must be dealt with, especially when the signal transmission line is long and the signal strength is low. This is a typical app...[Details]
Bloomberg reported that Chinese computer chip importers are increasing equipment purchases through Hong Kong channels, anticipating that U.S. sanctions on Hong Kong will make trade more difficult. In...[Details]
Introduction to ST7789 ST7789/ST7789V/ST7789H2, used to drive 262K color TFT-LCD in single chip, including 720 (240*3 colors) x 320 lines output, can be directly connected to external controller v...[Details]
Working principle of frequency converter
The prerequisite for the inverter to provide stable voltage and current to the load is to rectify the unstable AC power of the power grid into DC power...[Details]
Shanghai Advanced Micro-Semiconductor Equipment Co., Ltd. (hereinafter referred to as "ASME") announced today (28) that the company intends to increase its capital to Shanghai Ruili Scientific Instru...[Details]
At present, substation integrated automation technology has been widely used in my country. However, there are still some technical limitations in the application of the current substation integrated ...[Details]
Display There are two screens in the development board kit, the big one is LCD (liquid crystal display) and the small one is OLED (organic light emitting diode). Contrary to what you might think, the...[Details]
Motionchip is a special motion control chip with excellent performance, easy to expand and use. Based on this chip, this paper designs an intelligent servo driver that can be used for DC brushed/br...[Details]
The role of the watchdog: The watchdog timer is a counter whose basic function is to restart the system after a software problem or program runaway occurs. The watchdog counter counts automatically w...[Details]
In recent years, current mode circuits have aroused great interest in the academic community. Among them, current-controlled second-generation current conveyors (CCCII) and transconductance operationa...[Details]
The Wall Street Journal quoted senior Indian government officials and other sources as saying that Hon Hai is considering major expansion in India, including opening new factories and increasing the ...[Details]
VisionCore was established in 2020. In the following years, it successively introduced strategic investments from three listed companies including Sunny Optical, NetEase Youdao and ArcSoft. The com...[Details]
In the first half of this year, the global wearable device market ushered in growth. In addition to single products such as smart watches and TWS headphones, single products such as smart rings, op...[Details]
The rare earth giant magnetostrictive transducer is a device that converts electromagnetic energy into mechanical vibration using giant magnetostrictive materials. Compared with the widely used piezoe...[Details]
After a long period of rapid development, LED display screens
have now been widely used in the fields of finance, transportation, entertainment, sports, etc.
The display
part. With the r...[Details]
MCU
京公网安备 11010802033920号
EEWORLD
