EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

76000Y-25N-7JD

Description
MIL Series Connector, 99 Contact(s), Steel, Female, Crimp Terminal, Receptacle
CategoryThe connector    The connector   
File Size60KB,1 Pages
ManufacturerHiRel Connectors Inc
Websitehttps://hirelco.net
Download Datasheet Parametric View All

76000Y-25N-7JD Overview

MIL Series Connector, 99 Contact(s), Steel, Female, Crimp Terminal, Receptacle

76000Y-25N-7JD Parametric

Parameter NameAttribute value
Reach Compliance Codeunknown
Other featuresSTANDARD: MIL-DTL-38999
Back shell typeSOLID
Body/casing typeRECEPTACLE
Connector typeMIL SERIES CONNECTOR
Contact to complete cooperationNOT SPECIFIED
Contact point genderFEMALE
Coupling typeBAYONET
DIN complianceNO
empty shellNO
Environmental characteristicsCORROSION RESISTANT; ENVIRONMENT RESISTANT
Filter functionNO
IEC complianceNO
MIL complianceYES
Manufacturer's serial number76000Y
Plug informationMULTIPLE MATING PARTS AVAILABLE
Mixed contactsYES
Installation typePANEL
OptionsHERMETIC
Shell materialSTEEL
Housing size25
Termination typeCRIMP
Total number of contacts99
Base Number Matches1
How to use BOOSTXL-DRV8305 to drive a motor?
Dear experts: I have a C2000 launchpadTMS320F28027+BOOSTXL-DRV8305 set. Has anyone used this combination to drive a motor? Please give me some advice or provide some documents. I have read several off...
爱过流行 Microcontroller MCU
ads1220
1. How is the timeout set? Is it like this? 1*the number of clocks corresponding to the data update rate/256KHZ? For example, if I set the normal mode, the data acquisition is 20sps, and the DRDY conv...
wtyiyou Analogue and Mixed Signal
Raspberry Pico Review Summary
@fxyc87 Summary: [Raspberry Pi Pico Review]——by fxyc87 [Raspberry Pi Pico Review] - Unboxing + Download [Raspberry Pi Pico Review] - Start Programming [Raspberry Pi Pico Review] - Start compiling the ...
okhxyyo DIY/Open Source Hardware
stc89c51 drives transistor as switch circuit
I used the IO of stc89c51 to generate a square wave with a high level of 5v, a low level of 0V, and a duty cycle of 1kHZ and 80%, and then connected the IO to a transistor (as shown in the figure) to ...
rainnnn Analog electronics
How to modify the default value of protel99sePCB toolbar?
I am a beginner. When I draw a PCB board, the default values of the tools on the toolbar are all large. How can I make them smaller? Please help!...
Hxon PCB Design
XMC4800 Relax ECAT Kit Review 3 - Testing the EtherCAT Slave
[i=s]This post was last edited by tdatd on 2019-1-8 08:23[/i] After setting up the environment and lighting up the LED, we will go straight to our goal - ethercat communication. We will start the test...
tdatd Industrial Control Electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号