Burst Mode Multiplexed Flash Memory and Burst Mode
Multiplexed pSRAM
256 Mb (16 Mb x 16-bit) and 128 Mb (8 Mb x 16-bit) Flash
64 Mb (4 Mb x 16-bit), and 32 Mb (2 Mb x 16-bit) pSRAM
Data Sheet
(Preliminary)
S71NS-P Memory Subsystem Solutions Cover Sheet
Notice to Readers:
This document states the current technical specifications regarding the Spansion
product(s) described herein. Each product described herein may be designated as Advance Information,
Preliminary, or Full Production. See
Notice On Data Sheet Designations
for definitions.
Publication Number
S71NS-P_00
Revision
05
Issue Date
December 13, 2007
Data
Sheet
(Pre limin ar y)
Notice On Data Sheet Designations
Spansion Inc. issues data sheets with Advance Information or Preliminary designations to advise readers of
product information or intended specifications throughout the product life cycle, including development,
qualification, initial production, and full production. In all cases, however, readers are encouraged to verify
that they have the latest information before finalizing their design. The following descriptions of Spansion data
sheet designations are presented here to highlight their presence and definitions.
Advance Information
The Advance Information designation indicates that Spansion Inc. is developing one or more specific
products, but has not committed any design to production. Information presented in a document with this
designation is likely to change, and in some cases, development on the product may discontinue. Spansion
Inc. therefore places the following conditions upon Advance Information content:
“This document contains information on one or more products under development at Spansion Inc.
The information is intended to help you evaluate this product. Do not design in this product without
contacting the factory. Spansion Inc. reserves the right to change or discontinue work on this proposed
product without notice.”
Preliminary
The Preliminary designation indicates that the product development has progressed such that a commitment
to production has taken place. This designation covers several aspects of the product life cycle, including
product qualification, initial production, and the subsequent phases in the manufacturing process that occur
before full production is achieved. Changes to the technical specifications presented in a Preliminary
document should be expected while keeping these aspects of production under consideration. Spansion
places the following conditions upon Preliminary content:
“This document states the current technical specifications regarding the Spansion product(s)
described herein. The Preliminary status of this document indicates that product qualification has been
completed, and that initial production has begun. Due to the phases of the manufacturing process that
require maintaining efficiency and quality, this document may be revised by subsequent versions or
modifications due to changes in technical specifications.”
Combination
Some data sheets contain a combination of products with different designations (Advance Information,
Preliminary, or Full Production). This type of document distinguishes these products and their designations
wherever necessary, typically on the first page, the ordering information page, and pages with the DC
Characteristics table and the AC Erase and Program table (in the table notes). The disclaimer on the first
page refers the reader to the notice on this page.
Full Production (No Designation on Document)
When a product has been in production for a period of time such that no changes or only nominal changes
are expected, the Preliminary designation is removed from the data sheet. Nominal changes may include
those affecting the number of ordering part numbers available, such as the addition or deletion of a speed
option, temperature range, package type, or V
IO
range. Changes may also include those needed to clarify a
description or to correct a typographical error or incorrect specification. Spansion Inc. applies the following
conditions to documents in this category:
“This document states the current technical specifications regarding the Spansion product(s)
described herein. Spansion Inc. deems the products to have been in sufficient production volume such
that subsequent versions of this document are not expected to change. However, typographical or
specification corrections, or modifications to the valid combinations offered may occur.”
Questions regarding these document designations may be directed to your local sales office.
2
S71NS-P Memory Subsystem Solutions
S71NS-P_00_05 December 13, 2007
S71NS-P Memory Subsystem Solutions
MirrorBit
®
1.8 Volt-only Simultaneous Read/Write,
Burst Mode Multiplexed Flash Memory and Burst Mode
Multiplexed pSRAM
256 Mb (16 Mb x 16-bit) and 128 Mb (8 Mb x 16-bit) Flash
64 Mb (4 Mb x 16-bit), and 32 Mb (2 Mb x 16-bit) pSRAM
Data Sheet
(Preliminary)
Features
Power supply voltage of 1.7 V to 1.95 V
Burst Speed (Flash and pSRAM): 66 MHz, 83 MHz
MCP BGA Package
– 56 ball, 9.2 x 8.0 mm, 0.5 mm ball pitch
Operating Temperature
– Wireless, –25°C to +85°C
General Description
The S71NS-P Series is a product line of stacked Multi-Chip Package (MCP) memory solutions and consists of the following
items:
One or more S29NS-P flash memory die
Multiplexed pSRAM
The products covered by this document are listed in the table below. For details about their specifications, please refer to their
individual datasheet for further details.
pSRAM
Density
128 Mb
Flash
256 Mb
S71NS256PB0
S71NS256PC0
32 Mb
S71NS128PB0
64 Mb
S71NS128PC0
For detailed specifications, please refer to the individual data sheets:
Document
S29NS-P
32 M Multiplexed pSRAM Type 3
64 M Multiplexed pSRAM Type 3
Publication Identification Number
S29NS-P_00
muxpsram_04
muxpsram_01
Publication Number
S71NS-P_00
Revision
05
Issue Date
December 13, 2007
This document states the current technical specifications regarding the Spansion product(s) described herein. The Preliminary status of this document indicates that product qual-
ification has been completed, and that initial production has begun. Due to the phases of the manufacturing process that require maintaining efficiency and quality, this document
may be revised by subsequent versions or modifications due to changes in technical specifications.
Data
Sheet
(Pre limin ar y)
1.
Ordering Information
The order number is formed by a valid combinations of the following:
S71NS
256
P
C
0
ZJ
E
TV
0
Packing Type
0 = Tray
2 = 7-inch Tape and Reel
3 = 13-inch Tape and Reel
Model Number
See Valid Combinations table below
Package Modifier
E = 9.2 x 8.0, 56-ball BGA, 0.5mm ball pitch (0.3mm ball diameter)
Package Type
ZJ = Very Thin Fine-Pitch Ball Grid Array (VFBGA)—-1.2 mm max height with
Why does the body fat scale need AC impedance testing instead of testing the DC impedance of the human body? In fact, many biological or body fluid impedance tests are AC impedance rather than DC impe...
TI WEBENCH Design Tools
The process of WEBENCH design + ACDC 12V1A power supply design Xianyuntanyinghttps://en.eeworld.com/bbs/thread-446069-1-1.htmlShow the process of WEBENCH design + ACDC power su...
1. What is bootlloader?In an embedded operating system, BootLoader runs before the operating system kernel runs. It can initialize hardware devices and establish memory space mapping, thereby bringing...
The mains electricity standard in my country is 220V effective value and 50HZ AC frequency. It is divided into "neutral line" and "live line", the live line is connected to the phase line of the trans...
STM32 embeds a boot program in the chip production process, whose function is to download the program to Flash through the serial port, which provides great convenience for future software updates...[Details]
Real-time clock chip (RTC) is a small branch in the large family of integrated circuits with a wide variety of products. Its main function is to provide the electronic system with the current date an...[Details]
The signal polarity of the PWM output is determined by two options, one is the PWM mode, and the other is the output polarity control bit. Please see the block diagram of the timer. The selection of...[Details]
1 Introduction
Switching power supplies are small, light, and highly efficient, and are widely used in communications, automatic control, household appliances, computers, and other electro...[Details]
OFweek Cup · OFweek 2023 China
Robot
Industry Annual Selection (abbreviated as OFweek Robot Awards 2023) is jointly organized by OFweek, China's high-tech industry portal, and its authorita...[Details]
To properly select D/A conversion chips and related peripheral circuits, you need to understand the performance indicators and pin functions of various integrated circuits, as well as the functio...[Details]
Digital Video Configuration Tools
The primary challenge in embedding digital video into applications is that the complexity of implementing video goes far beyond simple image and audio compre...[Details]
State Grid Corporation of China recently issued a notice on key work tasks for 2020 (hereinafter referred to as the "Notice"), which detailed plans for 31 specific tasks in ten categories this year...[Details]
In the electronic control system, the analog circuit power supply is separated from the logic circuit power supply. The first is to remove the interference generated by the power supply coupling logi...[Details]
For hundreds of thousands of years, the human brain has been the most powerful computer on Earth. Our brains are an unparalleled evolutionary masterpiece that is capable of logic and reasoning, as...[Details]
GPS is the most mature and practical positioning system in technology. However, in the GPS positioning system, since it is a one-way navigation system, it transmits the ephemeris data to the ground...[Details]
1. Concept and definition of on-board charger
According to the definition in Electric Vehicle Terminology (GB/T 19596-2017), an on-board charger refers to a device that is fixedly installed on...[Details]
Recently, JinkoSolar announced that it has signed a 1.2MWh energy storage order with one of the largest power developers in Africa. The project will improve the local electricity environment an...[Details]
1. Preparation work 1.1 Schematic diagram CONFIG_DM9000_BASE The chip select signal is connected to the nGCS4 pin. To determine the base address of the network card, it must be determined acc...[Details]
Power technology
京公网安备 11010802033920号
EEWORLD
