This X25256 device has been acquired by
IC MICROSYSTEMS from Xicor; Inc.
Preliminary Information
256K
X25256
5MHz SPI Serial E
2
PROM with Block Lock
™
32K x 8 Bit
Protection
FEATURES
•5MHz Clock Rate
•Low Power CMOS
—<1µA standby current
—<5mA active current
•2.5V To 5.5V Power Supply
•SPI Modes (0,0 & 1,1)
•32K X 8 Bits
—64 byte page mode
•Block Lock
™
Protection
—Protect first page, first 2 pages, first 4 pages,
first 8 pages, 1/4, 1/2 or all of E
2PROM
array
•Programmable Hardware Write Protection
•Packages —8-
lead XBGA
—8-lead SOIC (JEDEC, EIAJ)
—20-lead TSSOP
DESCRIPTION
2
The X25256 is a CMOS 256K-bit serial E
PROM, inter-
nally organized as 32K x 8. The X25256 features a
Serial Peripheral Interface (SPI) and software protocol
allowing operation on a simple three-wire bus. The bus
signals are a clock input (SCK) plus separate data in
(SI) and data out (SO) lines. Access to the device is
controlled through a chip select (CS) input, allowing any
—In-circuit programmable ROM mode
•Built-In Inadvertent Write Protection
—Power-up/down protection circuitry
—Write enable latch
number of devices to share the same bus.
The X25256 also features two additional inputs that
provide the end user with added flexibility. By asserting
the HOLD input, the X25256 will ignore transitions on its
inputs, thus allowing the host to service higher priority
interrupts. The WP input can be used as a hardwire
input to the X25256 disabling all write attempts to the
status register, thus providing a mechanism for limiting
end user capability of altering first page, first 2 pages, 4
—Write protect pin
•Self-Timed Write Cycle
—5ms write cycle time (typical)
•High Reliability
—Endurance: 100,000 cycles
—Data Retention: 100 Years
—ESD protection: 2000V on all pins
pages, 8 pages, 0, 1/4, 1/2 or all of the memory.
FUNCTIONAL DIAGRAM
Status
Register
Write
Protect
32K Byte
Array
Logic
128
128 X 512
SO
SI
SCK
CS
Command
Decode
HOLD
And
Control
Logic
X-Decode
Protect
128
128 X 512
Logic
248
4
248 X 512
256 X 512
4 X 512
2 X 512
1 X 512
1 X 512
WP
Write
Control
And
Timing
Logic
2
1
1
64
8
Y Decode
Data Register
™
and Block Lock
™
Protection is a trademark of Xicor, Inc.
www.icmic.com
Characteristics subject to change without notice.
1 of 17
X25256 – Preliminary Information
The X25256 utilizes Xicor’s proprietary Direct Write
cell, providing a minimum endurance of 100,000 cycles
and a minimum data retention of 100 years.
™
PIN DESCRIPTIONS
Serial Output (SO)
SO is a push/pull serial data output pin. During a read
cycle, data is shifted out on this pin. Data is clocked out
PIN CONFIGURATION
8-Lead XBGA
HOLD
V
CC
by the falling edge of the serial clock.
Serial Input (SI)
SI is the serial data input pin. All opcodes, byte
addresses, and data to be written to the memory are
1
2
3
4
8
7
6
5
S0
CS
V
SS
SI
SCK
WP
input on this pin. Data is latched by the rising edge of the
serial clock.
Serial Clock (SCK)
8-Lead SOIC
CS
SO
WP
V
SS
1
2
3
4
X25256
8
7
6
5
CC
HOLD
SCK
V
The Serial Clock controls the serial bus timing for data
input and output. Opcodes, addresses, or data present
on the SI pin are latched on the rising edge of the clock
input, while data on the SO pin change after the falling
SI
edge of the clock input.
Chip Select (CS)
20-Lead TSSOP
CS
NC
1
2
3
4
5
6
7
8
9
10
SO
NC
NC
NC
NC
WP
NC
V
SS
20
19
18
17
16
X25256
15
14
13
12
11
V
CC
When CS is HIGH, the X25256 is deselected and the SO
output pin is at high impedance and unless an
internal write operation is underway, the X25256 will be in
the standby power mode. CS LOW enables the
X25256, placing it in the active power mode. It should be
noted that after power-up, a HIGH to LOW transition
NC
HOLD
NC
NC
NC
SCK
NC
NC
SI
on CS is required prior to the start of any operation.
Write Protect (WP)
When WP is LOW and the nonvolatile bit WPEN is “1”,
nonvolatile writes to the X25256 status register are dis-
abled, but the part otherwise functions normally. When WP
is held HIGH, all functions, including nonvolatile
writes operate normally. WP going LOW while CS is still
LOW will interrupt a write to the X25256 status reg-
PIN NAMES
Symbol
CS
SO
SI
SCK
Description
Chip Select Input
Serial Output
Serial Input
Serial Clock Input
Write Protect Input
Ground
Supply Voltage
Hold Input
No Connect
ister. If the internal write cycle has already been initi-
ated, WP going LOW will have no affect on a write.
The WP pin function is blocked when the WPEN bit in the
status register is “0”. This allows the user to install
the X25256 in a system with WP pin grounded and still be
able to write to the status register. The WP pin func-
WP
V
SS
V
CC
tions will be enabled when the WPEN bit is set “1”.
HOLD
NC
www.icmic.com
Characteristics subject to change without notice.
2 of 17
X25256
– Preliminary Information
Hold (HOLD)
HOLD is used in conjunction with the CS pin to pause the
device. Once the part is selected and a serial
sequence is underway, HOLD may be used to pause the
serial communication with the controller without
resetting the serial sequence. To pause, HOLD must be
brought LOW while SCK is LOW. To resume com-
munication,
HOLD is brought HIGH, again while SCK is
LOW. If the pause feature is not used, HOLD should be
held HIGH at all times.
Table 1. Instruction Set
Instruction Name
WREN
WRDI
RDSR
WRSR
READ
WRITE
Instruction Format*
0000 0110
0000 0100
0000 0101
0000 0001
0000 0011
0000 0010
Operation
Set the Write Enable Latch (Enable Write Operations)
Reset the Write Enable Latch (Disable Write Operations)
Read Status Register
Write Status Register
Read Data from Memory Array beginning at selected address
Write Data to Memory Array beginning at Selected Address (1 to 64 Bytes)
Notes:
*Instructions are shown MSB in leftmost position. Instructions are transferred MSB first.
PRINCIPLES OF OPERATION
2
The X25256 is a 32K x 8 E
PROM designed to interface
Status Register
The RDSR instruction provides access to the status
register. The status register may be read at any time,
even during a write cycle. The status register is format- ted
as follows:
directly with the synchronous serial peripheral interface (SPI)
of many popular microcontroller families.
The X25256 contains an 8-bit instruction register. It is
accessed via the SI input, with data being clocked in on
the rising SCK. CS must be LOW and the HOLD and
WP inputs must be HIGH during the entire operation.
7
WPEN
6
X
5
X
4
BL2
3
BL1
2
BL0
1
WEL
0
WIP
Table 1 contains a list of the instructions and their
opcodes. All instructions, addresses and data are
WPEN, BL0 and BL1 are set by the WRSR instruction.
WEL and WIP are read-only and automatically set by
transferred MSB first.
Data input is sampled on the first rising edge of SCK after
CS goes LOW. SCK is static, allowing the user to
stop the clock and then resume operations. If the clock
line is shared with other peripheral devices on the SPI
other operations.
The Write-In-Process (WIP) bit indicates whether the
X25256 is busy with a write operation. When set to a
“1”, a write is in progress, when set to a “0”, no write is
in progress. This bit is set and reset by hardware, it
cannot be controlled by the WRSR instruction. When
reading the Status Register while an internal nonvola-
bus, the user can assert the
HOLD input to place the
X25256 into a “PAUSE” condition. After releasing
HOLD, the X25256 will resume operation from the
point when HOLD was first asserted.
Write Enable Latch
The X25256 contains a “write enable” latch. This latch
must be SET before a write operation will be com-
pleted internally. The WREN instruction will set the
latch and the WRDI instruction will reset the latch. This
tile write is in progress, all bits output will be ‘1’. This
allows the programmer to use the WIP bit to determine
latch is automatically reset upon a power-up condition
and after the completion of a byte, page, or status reg-
an early end of write condition. It also allows the pro-
grammer to check for “FF” or “not FF” to determine end
of write. The programmer can also use the first one or two
bits received from the Status Register (if they were
known to be zero) to determine end of write. Each of
these techniques can simplify or speed the end of non-
volatile write detection.
ister write cycle.
www.icmic.com
Characteristics subject to change without notice.
3 of 17
X25256 – Preliminary Information
The Write Enable Latch (WEL) bit indicates the status of
the “write enable” latch. When set to a “1”, the latch is
set, when set to a “0”, the latch is reset. This bit is
controlled by hardware and cannot be written by the
WRSR instruction.
The Block Lock
(BL0, BL1, and BL2) bits are nonvola- tile
and allow the user to select one of eight levels of
protection. That is, the user may read the segments but
will be unable to alter (write) data within the selected
segments. The partitioning is controlled as illustrated in
the following table.
Status Register Bits
BL2
0
0
0
0
1
1
1
1
BL1
0
0
1
1
0
0
1
1
BL0
0
1
0
1
0
1
0
1
Array Addresses Protected
None
$6000–$7FFF (8K bytes)
$4000–$7FFF (16K bytes)
$0000–$7FFF (32K bytes)
$000–$03F (64 bytes)
$000–$07F (128 bytes)
$000–$0FF (256 bytes)
$000–$1FF (512 bytes)
Array Lock
None
Upper 1/4 (Q4)
Upper 1/2 (Q3, Q4)
Full Array (All)
First Page (P1)
First 2 Pages (P2)
First 4 Pages (P4)
First 8Pages (P8)
Figure 1. Block Lock Configurations
BL2-BL0
000
001
010
011
100
101
110
111
1/2 Array
3/4 Array
All Array
bit itself, as well as the block-protected sections in the
memory array. Only the sections of the memory array
that are not block-protected can be written.
In Circuit Programmable ROM Mode
Note that since the WPEN bit is write protected, it can- not
be changed back to a LOW state; so write protec-
tion is enabled as long as the WP pin is held LOW.
Thus an In Circuit Programmable ROM function can be
implemented by hardwiring the WP pin to Vss, writing to
and Block Locking the desired portion of the array to
be ROM, and then programming the WPEN bit HIGH.
The table above defines the program protect status for
each combination of WPEN and WP.
Clock and Data Timing
Data input on the SI line is latched on the rising edge
of SCK. Data is output on the SO line by the falling
The Write-Protect-Enable (WPEN) bit is available for the
X25256 as a nonvolatile enable bit for the WP pin.
Programmable Hardware Write Protection
The Write Protect (WP) pin and the nonvolatile Write
Protect Enable (WPEN) bit in the Status Register con-
trol the Programmable Hardware Write Protect feature.
Hardware Write Protection is enabled when WP pin is
edge of SCK.
Read Sequence
When reading from the
2
E
PROM memory array, CS is first
pulled LOW to select the device. The 8-bit READ instruction is
transmitted to the X25256, followed by the
LOW, and the WPEN bit is “1”. Hardware Write Protec-
tion is disabled when either the WP pin is HIGH or the
WPEN bit is “0”. When the chip is hardware write pro-
tected, nonvolatile writes are disabled to the Status
16-bit address of which the last 15 are used. After the
READ opcode and address are sent, the data stored in
Register, including the Block Lock bits and the WPEN
the memory at the selected address is shifted out on the SO
line. The data stored in memory at the next address
www.icmic.com
Characteristics subject to change without notice.
4 of 17
X25256
– Preliminary Information
can be read sequentially by continuing to provide clock
pulses. The address is automatically incremented to the
next higher address after each byte of data is shifted out.
When the highest address is reached ($7FFF) the
To read the status register the CS line is first pulled
LOW to select the device followed by the 8-bit RDSR
instruction. After the RDSR opcode is sent, the contents of
the status register are shifted out on the SO line.
address counter rolls over to address $0000 allowing the
read cycle to be continued indefinitely. The read operation
is terminated by taking CS HIGH. Refer to the read E
2
Figure 3 illustrates the read status register sequence.
PROM array operation sequence illustrated in Figure 2.
Memory Array Not
Block Protected
WP
HIGH
LOW
LOW
WPEN
X
0
1
Memory Array
Block Protected
Blocked
Blocked
Blocked
Block Lock
Bits
Writable
Writable
Writes Blocked
WPEN Bit
Writable
Writable
Writes Blocked
Protection
Software
Software
Hardware
Writable
Writable
Writable
Write Sequence
Prior to any attempt to write data into the X25256, the
“write enable” latch must first be set by issuing the
WREN instruction (See Figure 4). CS is first taken
LOW, then the WREN instruction is clocked into the
While the write is in progress following a status register or
E
2
PROM write sequence, the status register may be
read to check the WIP bit. During this time the WIP bit will
be HIGH.
X25256. After all eight bits of the instruction are trans-
mitted, CS must then be taken HIGH. If the user con-
tinues the write operation without taking CS HIGH after
issuing the WREN instruction, the write operation will
Hold Operation
The HOLD input should be HIGH (at V
IH
) under normal
operation. If a data transfer is to be interrupted HOLD
can be pulled LOW to suspend the transfer until it can
be ignored.
To write data to the
2
E
PROM memory array, the user
issues the WRITE instruction, followed by the address
and then the data to be written. This is minimally a thirty-
be resumed. The only restriction is the SCK input must be
LOW when HOLD is first pulled LOW and SCK must
also be LOW when HOLD is released.
The HOLD input may be tied HIGH either directly to V
CC
two clock operation. CS must go LOW and remain LOW for
the duration of the operation. The host may continue
to write up to 64 bytes of data to the X25256. The only
restriction is the 64 bytes must reside on the same
page. If the address counter reaches the end of the
page and the clock continues, the counter will “roll over”
or tied to V
CC
through a resistor.
Operational Notes
The X25256 powers-up in the following state:
– The device is in the low power standby state.
– A HIGH to LOW transition on CS is required to enter
an active state and receive an instruction. –
SO pin is high impedance.
– The “write enable” latch is reset.
to the first address of the page and overwrite any data
that may have been written.
For the write operation (byte or page write) to be com-
pleted, CS can only be brought HIGH after bit 0 of data
byte N is clocked in. If it is brought HIGH at any other
time the write operation will not be completed. Refer to
Figures 5 and 6 below for a detailed illustration of the write
sequences and time frames in which CS going
Data Protection
The following circuitry has been included to prevent
inadvertent writes:
HIGH are valid.
To write to the status register, the WRSR instruction is
followed by the data to be written. Data bits 0, 1, 5, and
– The “write enable” latch is reset upon power-up.
– A WREN instruction must be issued to set the “write
enable” latch.
– CS must come HIGH at the proper clock count in
6 are “don’t care”. Figure 7 illustrates this sequence.
order to start a write cycle.
www.icmic.com
Characteristics subject to change without notice.
5 of 17
Domestic Chip Exchange
京公网安备 11010802033920号
EEWORLD
