REVISION L
DO NOT
SCALE FROM
THIS PRINT
DESIGNED & DIMENSIONED
IN MILLIMETERS[INCHES]
FIG.2
RF179-XXXXX-XXXXXX-XXXX
CABLE CALLOUT
179: CCA-179 (RG-179 COAXIAL CABLE)
END 1 CONNECTOR
-72SP: MCX7-P-C-XX-ST-CA3 (SEE SHEET 2)
-72RP: MCX7-P-C-XX-RA-CA3 (SEE SHEET 2)
-74SP: BNC7T-P-C-XX-ST-CA3 (SEE SHEET 2)
-74BJ: BNC7T-J-C-XX-ST-BH3 (SEE SHEET 2)
-77SP: SMB7H-P-C-XX-ST-CA3 (SEE SHEET 2)
-77RP: SMB7H-P-C-XX-RA-CA3 (SEE SHEET 2)
*-D4SP: BNC7T-P-C-XX-ST-CA3-D (SEE SHEET 3)
*-78SP: DIN7A-PP-C-XX-ST-CA8 (SEE SHEET 3)
*-79SP: MBNC7-P-C-XX-ST-CA8 (SEE SHEET 3)
END 1 PLATING OPTION
1: GOLD ALL COMPONENTS
2: GOLD / NICKEL COMBINATION
3: ALTERNATE GOLD / NICKEL
(SEE SHEET 2 FOR PLATING SPECIFICS)
* = NOT RELEASED FOR PRODUCTION
CABLE STRIPPING DIMENSIONS
PER CONFIGURATIONS
(SEE TABLE 1)(SEE NOTE 12,13,14,15)
"A" mm
"B" mm
"C" mm
C
OVERALL CABLE LENGTH
MILLIMETERS OF CABLE
0100 MIN. (SEE NOTE 8 & 9)
END 2 PLATING OPTION
1: GOLD ALL COMPONENTS
2: GOLD / NICKEL COMBINATION
3: ALTERNATE GOLD / NICKEL
(LEAVE BLANK FOR -SING OR -XXXXXX
END 2 PREPARATION)
END 2 CONNECTOR OR PREPARATION
-72SP: MCX7-P-C-XX-ST-CA3 (SEE SHEET 2)
-72RP: MCX7-P-C-XX-RA-CA3 (SEE SHEET 2)
-74SP: BNC7T-P-C-XX-ST-CA3 (SEE SHEET 2)
-74BJ: BNC7T-J-C-XX-ST-BH3 (SEE SHEET 2)
-77SP: SMB7H-P-C-XX-ST-CA3 (SEE SHEET 2)
-77RP: SMB7H-P-C-XX-RA-CA3 (SEE SHEET 2)
*-D4SP: BNC7T-P-C-XX-ST-CA3-D (SEE SHEET 3)
*-78SP: DIN7A-PP-C-XX-ST-CA8 (SEE SHEET 3)
*-79SP: MBNC7-P-C-XX-ST-CA8 (SEE SHEET 3)
-SING: SINGLE ENDED (ONE END ONLY, SEE NOTE 11)
-XXXXXX: STRIPPED AND TINNED (THIS END ONLY-
SEE NOTE 11-15, SHEET 2, FIG. 3)
(SEE FIG. 2) "C" FORMAT: X.X
(SEE FIG. 2) "B" FORMAT: X.X
(SEE FIG. 2) "A" FORMAT: X.X
"D" mm
"E" mm
C
C
DO NOT LEAVE ANY SPACE BLANK,
EACH MUST CONTAIN A
NUMERIC CHARACTER 0 THRU 9.
NOTES:
1. C REPRESENTS A CRITICAL DIMENSION
2. CABLE CUT LENGTH:
= (LENGTH: XXXX) - (SUBTRACTOR FOR END 1) - (SUBTRACTOR FOR END 2)
C (SEE TABLE 1 FOR SUBTRACTORS)
3. ASSEMBLY TO BE 100% TESTED FOR OPENS & SHORTS
4. ASSEMBLY TO BE 100% HI-POT TESTED PER TABLE 1
C 5. AFTER FINAL ELECTRICAL TEST, LABEL EACH CABLE ASSEMBLY WITH 1 LABEL-ET
6. CRITICALS ON CONNECTOR PRINTS TO BE CHECKED IN PROCESS.
7. FINISHED ASSEMBLIES TO BE PACKAGED PER PACKAGING STANDARD CO-HD-WI-3033-M.
-LOCKWASHERS, NUTS, AND GASKETS TO BE SHIPPED UNASSEMBLED.
8. CABLE STOCKED IN INCHES, 1 INCH = 25.4 MILLIMETERS
9. CABLE LENGTHS LONGER THAN 500 MILLIMETERS ARE NOT SUPPORTED BY S.I. TEST DATA
10. MINIMUM BEND RADIUS FOR RG179 = 10.2 [.40].
11. FOR SING ENDED OR STRIPPED AND TINNED ASSEMBLIES: MAKE A DOUBLE ENDED
ASSEMBLY AT TWICE THE CABLE LENGTH AND TEST BEFORE CUTTING ASSEMBLY IN HALF.
12. DIM "A", "B", AND "C" HAVE A MINIMUM VALUE OF 0.0mm & A MAXIMUM VALUE OF 9.9mm
13. PRODUCTION OF STRIP AND TIN FOR CENTER DIELECTIC USE: A
14. PRODUCTION OF STRIP AND TIN FOR SHIELD USE: D=A+B
15. PRODUCTION OF STRIP AND TIN FOR JACKET USE: E=A+B+C
16. FOR -RA TO -RA, CONNECTOR SHOULD BOTH BE ORIENTED UP. (SEE SHEET 2, FIG. 4)
C
RF179-72SPX-72RPX-XXXX SHOWN
CABLE STRIPPING DIMENSIONS
PER END 1 AND END 2 ASSEMBLY PRINTS
OR STRIPPED AND TINNED
(SEE NOTES 11-15, SHEET 2, FIG. 3)
F:\DWG\MISC\MKTG\RF179-XXXXX-XXXXXX-XXXX-MKT.SLDDRW
FIG. 1
Pb THIS PRODUCT MANUFACTURED
WITH LEAD-FREE PROCESSING
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN
MILLIMETERS [INCHES].
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
TOLERANCES ARE:
DECIMALS
.X: 0.3 [.01]
2
.XX: 0.13 [.005]
.XXX: 0.051 [.0020]
ANGLES
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail info@SAMTEC.com
code 55322
DESCRIPTION:
DWG. NO.
MATERIAL:
SEE END 1 AND END 2 ASSEMBLY PRINTS
DO NOT SCALE DRAWING
SHEET SCALE: 2:1
RF179 CABLE ASSEMBLY
RF179-XXXXX-XXXXXX-XXXX
1-30-2007
BY:
B. RAY
SHEET
1
OF
3
REVISION L
(STRAIGHT PLUG)
-72SP
(RIGHT ANGLE PLUG)
(USE DRAWING No. MCX7-P-C-XX-RA-CA3
FOR ASSEMBLY INSTRUCTIONS)
-72RP
(STRAIGHT PLUG)
(USE DRAWING No. BNC7T-P-C-XX-ST-CA3
FOR ASSEMBLY INSTRUCTIONS)
-74SP
(USE DRAWING No. MCX7-P-C-XX-ST-CA3
FOR ASSEMBLY INSTRUCTIONS)
PLATING OPTIONS
1: 30μ" MIN. GOLD CENTER CONTACT
3μ" MIN. GOLD OUTER CONTACT
3μ" MIN. GOLD REMAINING METAL PARTS
(END CONNECTOR P/N: MCX7-P-C-H-ST-CA3)
2: 30μ" MIN. GOLD CENTER CONTACT
3μ" MIN. GOLD OUTER CONTACT
100μ" MIN. NICKEL REMAINING METAL PARTS
(END CONNECTOR P/N: MCX7-P-C-HN-ST-CA3)
NOTE: ALL CRITICAL DIMENSIONS ON MCX7-P-C-XX-ST-CA3
THAT APPLY MUST BE VERIFIED.
(STRAIGHT PLUG)
(USE DRAWING No. SMB7H-P-C-XX-ST-CA3
FOR ASSEMBLY INSTRUCTIONS)
PLATING OPTIONS
1: 30μ" MIN. GOLD CENTER CONTACT
3μ" MIN. GOLD OUTER CONTACT
3μ" MIN. GOLD REMAINING METAL PARTS
(END CONNECTOR P/N: MCX7-P-C-H-RA-CA3)
2: 30μ" MIN. GOLD CENTER CONTACT
3μ" MIN. GOLD OUTER CONTACT
100μ" MIN. NICKEL REMAINING METAL PARTS
(END CONNECTOR P/N: MCX7-P-C-HN-RA-CA3)
NOTE: ALL CRITICAL DIMENSIONS ON MCX7-P-C-XX-RA-CA3
THAT APPLY MUST BE VERIFIED.
(RIGHT ANGLE PLUG)
(USE DRAWING No. SMB7H-P-C-XX-RA-CA3
FOR ASSEMBLY INSTRUCTIONS)
PLATING
3: 10μ" MIN. GOLD CENTER CONTACT
100μ" MIN. NICKEL OUTER CONTACT
100μ" MIN. NICKEL REMAINING METAL PARTS
(END CONNECTOR P/N: BNC7T-P-C-MN-ST-CA3)
NOTE: ALL CRITICAL DIMENSIONS ON BNC7T-P-C-XX-ST-CA3
THAT APPLY MUST BE VERIFIED.
(STRAIGHT BULKHEAD JACK)
(USE DRAWING No. BNC7T-J-C-XX-ST-BH3
FOR ASSEMBLY INSTRUCTIONS)
-77SP
-77RP
-74BJ
PLATING OPTIONS
1: 30μ" MIN. GOLD CENTER CONTACT
3μ" MIN. GOLD OUTER CONTACT
3μ" MIN. GOLD REMAINING METAL PARTS
(END CONNECTOR P/N: SMB7H-P-C-H-ST-CA3)
2: 30μ" MIN. GOLD CENTER CONTACT
3μ" MIN. GOLD OUTER CONTACT
100μ" MIN. NICKEL REMAINING METAL PARTS
(END CONNECTOR P/N: SMB7H-P-C-HN-ST-CA3)
NOTE: ALL CRITICAL DIMENSIONS ON SMB7H-P-C-XX-ST-CA3
THAT APPLY MUST BE VERIFIED.
PLATING OPTIONS
1: 30μ" MIN. GOLD CENTER CONTACT
3μ" MIN. GOLD OUTER CONTACT
3μ" MIN. GOLD REMAINING METAL PARTS
(END CONNECTOR P/N: SMB7H-P-C-H-RA-CA3)
2: 30μ" MIN. GOLD CENTER CONTACT
3μ" MIN. GOLD OUTER CONTACT
100μ" MIN. NICKEL REMAINING METAL PARTS
(END CONNECTOR P/N: SMB7H-P-C-HN-RA-CA3)
NOTE: ALL CRITICAL DIMENSIONS ON SMB7H-P-C-XX-RA-CA3
THAT APPLY MUST BE VERIFIED.
PLATING OPTIONS
2: 30μ" MIN. GOLD CENTER CONTACT
100μ" MIN. NICKEL OUTER CONTACT
100μ" MIN. NICKEL REMAINING METAL PARTS
(END CONNECTOR P/N: BNC7T-J-C-HN-ST-BH3)
3: 10μ" MIN. GOLD CENTER CONTACT
100μ" MIN. NICKEL OUTER CONTACT
100μ" MIN. NICKEL REMAINING METAL PARTS
(END CONNECTOR P/N: BNC7T-J-C-MN-ST-BH3)
NOTE: ALL CRITICAL DIMENSIONS ON BNC7T-J-C-XX-ST-BH3
THAT APPLY MUST BE VERIFIED.
F:\DWG\MISC\MKTG\RF179-XXXXX-XXXXXX-XXXX-MKT.SLDDRW
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail info@SAMTEC.com
code 55322
DESCRIPTION:
DWG. NO.
DO NOT SCALE DRAWING
SHEET SCALE: 1:1
RF179 CABLE ASSEMBLY
RF179-XXXXX-XXXXXX-XXXX
1-30-2007
SHEET
2
OF
3
BY:
B. RAY
REVISION L
(DIE CAST STRAIGHT PLUG)
(USE DRAWING No. BNC7T-P-C-XX-ST-CA3-D
FOR ASSEMBLY INSTRUCTIONS)
-D4SP
(STRAIGHT PLUG)
(USE DRAWING No. DIN7A-PP-C-XX-ST-CA8
FOR ASSEMBLY INSTRUCTIONS)
-78SP
(STRAIGHT PLUG)
(USE DRAWING No. MBNC7-P-C-XX-ST-CA8
FOR ASSEMBLY INSTRUCTIONS)
-79SP
PLATING
3: 10μ" MIN. GOLD CENTER CONTACT
100μ" MIN. NICKEL OUTER CONTACT
100μ" MIN. NICKEL REMAINING METAL PARTS
(END CONNECTOR P/N: BNC7T-P-C-MN-ST-CA3-D)
NOTE: ALL CRITICAL DIMENSIONS ON BNC7T-P-C-XX-ST-CA3-D
THAT APPLY MUST BE VERIFIED.
PLATING
4: 10μ" MIN. GOLD CENTER CONTACT
3μ" MIN. GOLD OUTER CONTACT
100μ" MIN. NICKEL REMAINING METAL PARTS
(END CONNECTOR P/N: DIN7A-PP-C-MF-ST-CA8)
5: 10μ" MIN. GOLD CENTER CONTACT
10μ" MIN. GOLD OUTER CONTACT
100μ" MIN. NICKEL REMAINING METAL PARTS
(END CONNECTOR P/N: DIN7A-PP-C-MM-ST-CA8)
6: 30μ" MIN. GOLD CENTER CONTACT
30μ" MIN. GOLD OUTER CONTACT
100μ" MIN. NICKEL REMAINING METAL PARTS
(END CONNECTOR P/N: DIN7A-PP-C-HH-ST-CA8)
NOTE: ALL CRITICAL DIMENSIONS ON DIN7A-PP-C-XX-ST-CA8
THAT APPLY MUST BE VERIFIED.
PLATING
2: 30μ" MIN. GOLD CENTER CONTACT
100μ" MIN. NICKEL OUTER CONTACT
100μ" MIN. NICKEL REMAINING METAL PARTS
(END CONNECTOR P/N: MBNC7-P-C-HN-ST-CA8)
3: 10μ" MIN. GOLD CENTER CONTACT
100μ" MIN. NICKEL OUTER CONTACT
100μ" MIN. NICKEL REMAINING METAL PARTS
(END CONNECTOR P/N: MBNC7-P-C-MN-ST-CA8)
NOTE: ALL CRITICAL DIMENSIONS ON MBNC7-P-C-XX-ST-CA8
THAT APPLY MUST BE VERIFIED.
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail info@SAMTEC.com
code 55322
DESCRIPTION:
DWG. NO.
DO NOT SCALE DRAWING
SHEET SCALE: 1:1
RF179 CABLE ASSEMBLY
F:\DWG\MISC\MKTG\RF179-XXXXX-XXXXXX-XXXX-MKT.SLDDRW
BY:
B. RAY
RF179-XXXXX-XXXXXX-XXXX
1-30-2007
SHEET
3
OF
3
京公网安备 11010802033920号
EEWORLD
