FUJITSU SEMICONDUCTOR
DATA SHEET
DS07-12605-1E
8-bit Proprietary Microcontrollers
CMOS
F
2
MC-8FX MB95110H Series
MB95117H/F118HS/F118TS/F118HW/F118TW/
MB95FV100B-103
■
DESCRIPTION
The MB95110H series is general-purpose, single-chip microcontrollers. In addition to a compact instruction set,
the microcontrollers contain a variety of peripheral functions.
Note : F
2
MC is the abbreviation of FUJITSU Flexible Microcontroller.
■
FEATURES
•
F
2
MC-8FX CPU core
Instruction set optimized for controllers
• Multiplication and division instructions
• 16-bit arithmetic operations
• Bit test branch instruction
• Bit manipulation instructions etc.
•
Clock
• Main clock
• Main PLL clock
• Sub clock (for dual clock product)
• Sub PLL clock (for dual clock product)
•
Timer
• 8/16-bit compound timer
×
2 channels
• 8/16-bit PPG
×
2 channels
• 16-bit PPG
• Timebase timer
• Watch prescaler (for dual clock product)
(Continued)
Be sure to refer to the “Check Sheet” for the latest cautions on development.
“Check Sheet” is seen at the following support page
URL : http://www.fujitsu.com/global/services/microelectronics/product/micom/support/index.html
“Check Sheet” lists the minimal requirement items to be checked to prevent problems beforehand in system
development.
Copyright©2006 FUJITSU LIMITED All rights reserved
MB95110H Series
(Continued)
•
LIN-UART
• Full duplex double buffer
• Clock asynchronous or clock synchronous serial data transfer capable
•
UART/SIO
• Full duplex double buffer
• Clock asynchronous or clock synchronous serial data transfer capable
•
I
2
C*
Built-in wake-up function
•
External interrupt
• Interrupt by edge detection (rising, falling, or both edges can be selected)
• Can be used to recover from low-power consumption (standby) modes.
•
8/10-bit A/D converter
8-bit or 10-bit resolution can be selected
•
Low-power consumption (standby) mode
• Stop mode
• Sleep mode
• Watch mode (for dual clock product)
• Timebase timer mode
•
I/O port
• The number of maximum ports
•
Single clock product : 39 ports
•
Dual clock product : 37 ports
• Configuration
•
General-purpose I/O ports (N-ch open drain) : 2 ports
•
General-purpose I/O ports (CMOS)
: Single clock product : 37 ports
Dual clock product : 35 ports
* : Purchase of Fujitsu I
2
C components conveys a license under the Philips I
2
C Patent Rights to use, these com-
ponents in an I
2
C system provided that the system conforms to the I
2
C Standard Specification as defined by
Philips.
2
MB95110H Series
■
PRODUCT LINEUP
Part number
MB95117H
Parameter
Type
ROM capacity
RAM capacity
Reset output
Option*
2
Clock system
Low voltage detection
reset
Selectable
single/dual
clock*
1
Yes / No
No
Single clock
MASK ROM
product
48 Kbytes
2 Kbytes
Yes
Dual clock
Flash memory product
60 Kbytes
2 Kbytes
MB95F118HS
MB95F118TS
MB95F118HW MB95F118TW
Yes
No
Yes
CPU functions
Number of basic instructions
Instruction bit length
Instruction length
Data bit length
Minimum instruction execution time
Interrupt processing time
: 136
: 8 bits
: 1 to 3 bytes
: 1, 8, and 16 bits
: 0.1
µs
(at machine clock frequency 10 MHz)
: 0.9
µs
(at machine clock frequency 10 MHz)
General purpose I/O
ports
Timebase timer
Watchdog timer
Peripheral functions
Wild register
•
Single clock product : 39 ports (N-ch open drain : 2 ports, CMOS : 37 ports)
•
Dual clock product : 37 ports (N-ch open drain : 2 ports, CMOS : 35 ports)
Interrupt cycle : 0.5 ms, 2.1 ms, 8.2 ms, 32.8 ms (at main oscillation clock 4 MHz)
Reset generated cycle
At main oscillation clock 10 MHz
: Min 105 ms
At sub oscillation clock 32.768 kHz (for dual clock product) : Min 250 ms
Capable of replacing 3 bytes of ROM data
Master/slave sending and receiving
Bus error function and arbitration function
Detecting transmitting direction function
Start condition repeated generation and detection functions
Built-in wake-up function
Data transfer capable in UART/SIO
Full duplex double buffer, variable data length (5/6/7/8-bit), built-in baud rate
generator
Transfer rate : 2400 bps to 1250000 bps (at machine clock 10 MHz)
NRZ type transfer format, error detected function
LSB-first or MSB-first can be selected.
Clock synchronous (SIO) or clock asynchronous (UART) serial data transfer capable
(Continued)
I
2
C
UART/SIO
3
MB95110H Series
(Continued)
Part number
MB95117H
Parameter
Dedicated reload timer allowing a wide range of communication speeds to be set.
Full duplex double buffer.
Capable of serial data transfer synchronous or asynchronous to clock signal.
LIN functions available as the LIN master or LIN slave.
MB95F118HS
MB95F118TS
MB95F118HW MB95F118TW
LIN-UART
8/10-bit A/D converter
8-bit or 10-bit resolution can be selected.
(8 channels)
Each channel of the timer can be used as “8-bit timer
×
2 channels” or “16-bit timer
×
1 channel”.
Built-in timer function, PWC function, PWM function, capture function, and square
waveform output
Count clock : 7 internal clocks and external clock can be selected
PWM mode or one-shot mode can be selected.
Counter operating clock : 8 selectable clock sources
Support for external trigger start
Each channel of the PPG can be used as
“
8-bit PPG
×
2 channels
”
or
“
16-bit PPG
×
1 channel
”
.
Counter operating clock : Eight selectable clock sources
Peripheral functions
8/16-bit compound
timer (2 channels)
16-bit PPG
8/16-bit PPG
(2 channels)
Count clock : 4 selectable clock sources (125 ms, 250 ms, 500 ms, or 1 s)
Watch counter
Counter value can be set from 0 to 63. (Capable of counting for 1minute when
(for dual clock product)
selecting clock source 1 second and setting counter value to 60)
Watch prescaler
4 selectable interval times (125 ms, 250 ms, 500 ms, or 1 s)
(for dual clock product)
External interrupt
(12 channels)
Standby mode
Interrupt by edge detection (rising, falling, or both edges can be selected.)
Can be used to recover from standby modes.
Sleep, stop, watch (for dual clock product) , and timebase timer
The evaluation device of this product is MB95FV100B-103. MCU board is MB2146-303.
*1 : Specify clock mode when ordering MASK ROM.
*2 : For details of option, refer to “■ MASK OPTION”.
Note : Part number of the evaluation device in MB95110H series is MB95FV100B-103. When using it, the MCU
board (MB2146-303) is required.
4
MB95110H Series
■
OSCILLATION STABILIZATION WAIT TIME
The initial value of the main clock oscillation stabilization wait time is fixed to the maximum value. The maximum
value is shown as follows.
Oscillation stabilization wait time
(2
14
−2)
/F
CH
Remarks
Approx. 4.10 ms (at main oscillation clock 4 MHz)
■
PACKAGES AND CORRESPONDING PRODUCTS
Part number
MB95117H
Package
FPT-52P-M01
BGA-224P-M08
: Available
: Unavailable
MB95F118HS
MB95F118TS
MB95F118HW
MB95F118TW
MB95FV100B-103
5