EEWORLDEEWORLDEEWORLD

Part Number

Search

R5460N208AA-TR-FE

CategoryPower/power management    Battery protection chip   
ManufacturerRICOH
Websitehttp://www.e-devices.ricoh.co.jp/
Download Datasheet Compare View All

R5460N208AA-TR-FE Online Shopping

Suppliers Part Number Price MOQ In stock  
R5460N208AA-TR-FE - - View Buy Now
R5460x2xx SERIES
Li-ION/POLYMER 2-CELL PROTECTOR
NO.EA-165-160603
OUTLINE
The R5460x2xxxx Series are high voltage CMOS-based protection ICs for over-charge/discharge of rechargeable two-cell
Lithium-ion (Li+) / Lithium polymer, further include a short circuit protection circuit for preventing large external short circuit
current and the protection circuits against the excess discharge-current and excess charge current.
Each of these ICs is composed of six voltage detectors, a reference unit, a delay circuit, a short circuit protector, an oscillator,
a counter, and a logic circuit. When the over-charge voltage threshold or excess-charge current threshold crosses the each
detector threshold from a low value to a high value, the output of C
OUT
pin switches to “L” level after internal fixed delay time.
To release over-charge detector after detecting over-charge, the detector can be reset and the output of C
OUT
becomes "H"
when a kind of load is connected to V
DD
after a charger is disconnected from the battery pack and the cell voltage becomes
lower than over-charge detector threshold. In case that a charger is continuously connected to the battery pack, if the cell
voltage becomes lower than the over-charge released voltage, over-charge state is also released.
The output of D
OUT
pin, the output of the over-discharge detector and the excess discharge-current detector, switches to “L”
level after internally fixed delay time, when discharged voltage crosses the detector threshold from a high value to a value
lower than V
DET2
.
The conditions to release over-discharge voltage detector after detecting over-discharge voltage are as follows:
A/D versions: after connecting a charger, when the cell voltage becomes higher than over-discharge detector threshold or,
without connecting charger, when the cell voltage becomes equal or higher than over-discharge released voltage.
C version: after connecting a charger, when the cell voltage becomes higher than over-discharge detector threshold voltage.
E version: whether connecting a charger, or not, when the cell voltage becomes higher than released voltage from over-
discharge.
F version: after connecting a charger, when the cell voltage becomes higher than released voltage from over-discharge.
In case that connecting a charger, for A/C/D versions, there is no hysteresis for over-discharge detector. E/F versions, even if
a charger is connected to the battery pack, the hysteresis of over-discharge detector exists.
To satisfy the release conditions for over-discharge voltage protector, the output voltage of D
OUT
becomes "H".
Even if a battery is discharged to 0V, charge current is acceptable.
After detecting excess-discharge current or short current, when the load is disconnected, the excess discharged or short
condition is released and D
OUT
becomes “H”.
After detecting over-discharge voltage, supply current will be kept extremely low by halting internal circuits' operation.
When the output of C
OUT
is “H”, if V- pin level is set at -1.6V, the delay time of over-charge and over-discharge detector can be
shortened. Especially, the delay time of the over-charge detector can be reduced into approximately 1/60 and test time for
protection circuit PCB can be reduced. The output type of C
OUT
and D
OUT
is CMOS.
1
I would like to ask which manufacturers produce unipolar TMR tunneling effect switches. I only found MDT, and Magne does not have unipolar ones.
I would like to ask which manufacturers produce single-pole TMR switches. I only found MDT, and Magne does not have single-pole ones....
一沙一世 Sensor
Altium16.1 manufacturing output IPC-2581 and odb++ formats are not working
Altium16.1 manufacturing output IPC-2581 and odb++ formats are not possible.Both formats prompt this error, how to solve it?...
xy598646744 PCB Design
Three Key Points to Successfully Solving FPGA Design Timing Problems
Three Key Points to Successfully Solving FPGA Design Timing Problems...
zxopenljx EE_FPGA Learning Park
[CY8CKIT-149 PSoC 4100S Review] + Software Installation and Program Download
[i=s]This post was last edited by DDZZ669 on 2018-11-21 18:19[/i] [md]## Software Installation According to the [CY8CKIT-149 User Manual]([url=https://en.eeworld.com/bbs/forum.php?mod=attachment&aid=M...
DDZZ669 MCU
[Project source code] Modify waveform display color based on FPGA Modelsim
This article and design code were written by FPGA enthusiast Xiao Meige. Without the author's permission, this article is only allowed to be copied and reproduced on online forums, and the original au...
小梅哥 Altera SoC
What is the operating system generally used on airplanes?
Aviation software is not mysterious. From the perspective of computer architecture, it is not much different from ordinary computer systems. It is composed of processors, buses, I/O devices, storage d...
赵玉田 Talking

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号