SpecNo.JEFL243C-0005S-01
Reference Only
Reference Specification
P 1/9
Chip Common Mode Choke Coil
DLW21HN□□□SQ2□
1. Scope
This reference specification applies to Chip Common Mode Choke Coil DLW21H Series.
2. Part Numbering
DL W
21 H N
(1)
(2) (3) (4) (5)
(1) Chip Common Mode Choke Coil
(2) Structure (W : Winding Type)
(3) Dimension (LW)
(4) Type
(5) Category
(ex.)
670
(6)
S Q
2 L
(7) (8) (9) (10)
(6) Impedance (Typ. at 100MHz)
(7) Circuit
(8) Features
(9) Number of Line
(10) Packaging Code L : Taping / B : Bulk
3. Rating
Customer
Part Number
Murata
Part Number
Insulation
DC
Common Mode Impedance Rated Withstanding Rated
Current Resistance Resistance
Voltage
Voltage
(at 100MHz, Under
( max.) (Mmin.)
(mA)
V(DC)
Standard Testing Condition) V(DC)
( )
DLW21HN181SQ2L
DLW21HN181SQ2B
DLW21HN121SQ2L
DLW21HN121SQ2B
DLW21HN900SQ2L
DLW21HN900SQ2B
DLW21HN670SQ2L
DLW21HN670SQ2B
Operating Temperature : -40 to +85°C
180 ± 25 %
120 ± 25 %
50
90 ± 25 %
67 ± 25 %
Storage Temperature
125
250
280
330
330
: -40 to +85°C
0.50
0.45
10
0.35
0.35
4. Standard Testing Condition
<
Unless otherwise specified>
Temperature : Ordinary Temperature 15 to 35°C
Humidity : Ordinary Humidity 25 to 85%(RH)
<
In case of doubt>
Temperature : 20 ± 2°C
Humidity : 60 to 70%(RH)
Atmospheric Pressure : 86 to106kPa
5. Style and Dimensions
0 .9 ±0 .1
( 0 . 1 7 )
2.0±0.2
1.2±0.2
■
Equivalent Circuits
(1)
(2)
(0.45)
(1)
(0.45)
(2)
(0.4)
:Electrode
() : Reference Value
(0.4)
(in mm)
(4)
(3)
No polarity
■
Unit Mass (Typical value)
0.009g
(4)
(3)
6. Marking
No Marking.
7. Electrical Performance
No.
7.1
Item
Common Mode
Impedance
(Zc)
Specification
Meet item 3.
Measuring
4291A or the
equivalent
Measuring Frequency : 100±1MHz(ref.item 10,11)
Test Method
Equipment : Agilent
MURATA MFG.CO.,LTD
SpecNo.JEFL243C-0005S-01
No.
7.2
7.3
Item
Withstanding
Voltage
DC Resistance
(Rdc)
Insulation
Resistance (I.R.)
Reference Only
P 2/9
Specification
Products shall not be
damaged.
Meet item 3.
7.4
Test Method
Test Voltage : 2.5 times for Rated Voltage
Time : 5±1 s
Charge Current : 1 mA max. (ref.item 10)
Measuring current : 100mA max. (ref.item 10)
(In
case of doubt in the above mentioned standard
condition, measure by 4 terminal method.)
Measuring voltage : Rated Voltage
Measuring time : 1 minute max. (ref.item 10)
8. Mechanical Performance
No.
8.1
8.2
Item
Appearance and
Dimensions
Bonding Strength
Specification
Meet item 5.
No evidence of coming off
substrate.
Products shall not be
mechanical damaged.
Test Method
Visual Inspection and measured with Slide Calipers
or Micrometer.
It shall be soldered on the substrate.
Applying Force(F) : 5N
Applying Time : 5±1seconds
Pressure
Substrate
Product
Test board fixture
8.3
Bending Strength
Meet Table 1.
Table 1
Appearance
Common Mode
Impedance
Change
I.R.
Withstanding
Voltage
No damaged
within
±20%
10MΩ min.
It shall be soldered on the Glass-epoxy substrate.
Deflection : 2mm
(t=1.0mm).
Keeping time : 5 seconds
Speed of Applying Force : 0.5mm/s
Pressure jig
F
Deflection
45
45
Product
R230
No damaged
8.4
Drop
8.5
Vibration
8.6
Solderability
The electrodes shall be at least
90% covered with new solder
coating.
8.7
Resistance to
Soldering Heat
Meet Table 1.
It shall be dropped on concrete or steel board.
Method : free fall
Height : 1 m
The Number of Times : 3 times
It shall be soldered on the substrate.
Oscillation Frequency : 10 to 55 to 10Hz for 1 minute
Total Amplitude : 1.5mm
Testing Time : A period of 2 hours in each of 3
mutually perpendicular directions. (Total 6 hours)
Flux:Ethanol solution of rosin,25(wt)% includes
activator equivalent to 0.06 to 0.10(wt)% chlorine
Pre-Heating : 80 to 120°C 1minute
Solder : Sn-3.0Ag-0.5Cu
Solder Temperature : 245±3°C
Immersion Time : 4±1 seconds
Immersion and emersion rates : 25mm/s
Flux : Ethanol solution of rosin,25(wt)% includes
activator equipment to 0.06 to 0.10(wt)% chlorine
Pre-Heating : 80 to 120°C, 1minute
Solder : Sn-3.0Ag-0.5Cu
Solder Temperature : 260±5°C
Immersion Time : 5±0.5 seconds
Immersion and emersion rates : 25mm/s
Then measured after exposure in the room
condition for 4 to 48 hours.
MURATA MFG.CO.,LTD
SpecNo.JEFL243C-0005S-01
9. Environmental Performance(Products
shall be soldered on the substrate.)
No.
9.1
Item
Temperature
Cycle
Specification
Meet Table 1.
Reference Only
Test Method
P 3/9
9.2
Humidity
9.3
Heat life
9.4
Cold Resistance
1 Cycle
Step 1 -40°C(+0°C,-3°C) / 30±3 min
Step 2 Ordinary Temp. / 10 to 15 minutes
Step 3 +85°C(+3°C,-0°C) / 30±3 min
Step 4 Ordinary Temp. / 10 to 15 minutes
Total of 10 cycles
Then measured after exposure in the
room condition for 4 to 48 hours
Temperature : 40±2°C
Humidity : 90~95%(RH)
Time : 1000(+48 hours,-0 hours)
Then measured after exposure in the
room condition for 4 to 48 hours.
Temperature : 85±2°C
Applying Voltage : 2times for Rated Voltage
Time : 1000(+48 hours,-0 hours)
Then measured after exposure in the
room condition for 4 to 48 hours. (ref.item 10)
Temperature : -40± 2°C
Time : 1000(+48 hours,-0 hours)
Then measured after exposure in the
room condition for 4 to 48 hours.
10. Terminal to be Tested.
When measuring and suppling the voltage,the following terminal is applied.
No.
Item
Terminal to be Tested
10.1
Common Mode Impedance
Terminal
(Measurement Terminal)
10.2
Withstanding Voltage
(Measurement Terminal)
DC Resistance
(Measurement Terminal)
Terminal
Terminal
Terminal
10.3
Terminal
Terminal
Terminal
Terminal
10.4
Insulation Resistance
(Measurement Terminal)
Heat Life(Supply Terminal)
Terminal
Terminal
10.5
11. Measuring method for common mode impedance.
Measured common mode impedance may be included measurement error due to stray capacitance,
residual inductance of test fixture.
To correct this error, the common mode impedance should be calculate as follows;
(1) Measure admittance of the fixture(opened), Go Bo.
(2) Measure impedance of the fixture(shorted), Rs Xs.
(3) Measure admittance of the specimen, Gm Bm.
(4) Calculate corrected impedance
Z
using the formula below.
Z
= (Rx
2
+Xx
2
)
1/2
Where
Gm-Go
Rx = (Gm-Go)
2
+ (Bm-Bo)
2
- Rs
-(Bm- Bo)
Xx = (Gm-Go)
2
+ (Bm-Bo)
2
- Xs
MURATA MFG.CO.,LTD
SpecNo.JEFL243C-0005S-01
Reference Only
P 4/9
12. P.C.B., Flux, Solder and Soldering condition
Test shall be done using P.C.B., Flux, Solder and Soldering condition which are
specified in item 16 except the case of being specified special condition.
13. Impedance Frequency Characteristics(Typical)
10000
DLW21HＮ181SQ2
1000
Common Mode
DLW21HＮ121SQ2
DLW21HN900SQ2
l Z l （Ω）
100
DLW21HN670SQ2
10
DLW21HＮ181SQ2
1
DLW21HＮ121SQ2
DLW21HN900SQ2
DLW21HN670SQ2
Differential Mode
100
1000
0.1
1
10
f （ＭＨz)
14. Specification of Packaging
14.1 Appearance and Dimensions ( 8mm-wide,Plastic tape)
1.75±0.1
Sprocket Hole
1.5±
0.1
0
4.0±0.1
2.0±0.05
0.25±0.05
8.0±0.3
3.5±0.05
2.3±0.1
*
Dimension of the Cavity is measured
at the bottom side.
1.1±0.1
1.55±0.1
4.0±0.1
Cavity
Direction of feed
(in mm)
14.2 Specification of Taping
(1)Packing quantity(Standard quantity) 3000 pcs. / reel
(2)Packing Method
Products shall be packaged in each embossed cavity of plastic tape and sealed with cover tape.
(3) Spliced point
The cover tape have no spliced point.
(4) Sprocket Hole
Sprocket hole shall be located on the left hand side toward the direction of feed.
(5)Missing components number
Missing components number within 0.1% of the number per reel or 1 pc., whichever is greater,and are not
continuous.The specified quantity per reel is kept.
14.3 Pull Strength of Plastic Tape
Plastic Tape
Cover Tape
14.4 Peeling off force of Cover Tape
0.2 to 0.7N(Minimum value is Typical)
Speed of Peeling off : 300 mm / min
5N min.
10N min.
165 to 180 degree
F
Cover tape
Plastic tape
MURATA MFG.CO.,LTD
SpecNo.JEFL243C-0005S-01
Reference Only
Trailer
Leader
Label
190 min.
Empty tape
13.0±0.2
P 5/9
14.5 Dimensions of Leader-tape, Trailer and Reel
2.0±0.5
160 min.
210 min.
Top tape
60±
0
1
9±
1
0
13±1.4
180±
3
0
21.0±0.8
Direction of feed
14.6 Marking for reel
Customer part number, MURATA part number, Inspection number(1), RoHS discrimination(2), Quantity, etc
1)
« Expression of Inspection No. »
□□
OOOO
(1)
Factory Code
(2)
Date
(3)
Serial No.
(1)
(2)
(3)
First digit
: Year / Last digit of year
Second digit
: Month / Jan. to Sep.
1 to 9, Oct. to Dec.
O,N,D
Third, Fourth digit : Day
ROHS – Y (△)
(1) (2)
2)
« Expression of RoHS discrimination »
(1)
RoHS regulation conformity parts.
(2)
MURATA classification number
14.7 Marking for Outside package
Customer name Purchasing Order Number, Customer Part Number, MURATA part number,
RoHS discrimination(2), Quantity, etc
14.8 Specification of Outer Case
Label
H
D
W
Outer Case Dimensions
Standard Reel Quantity in Outer Case
(mm)
(Reel)
W
D
H
186
186
93
5
Above
Outer Case size is typical. It depends on a quantity of an
order.
15.
!
△
Caution
15.1 Mounting Direction
Mount products in right direction.
Wrong direction which is 90°rotated from right direction causes not only open or short circuit but also
flames or other serious trouble.
Ｚ
Ｚ
right direction
wrong direction
15.2 Limitation of Applications
Please contact us before using our products for the applications listed below which require especially
high reliability for the prevention of defects which might directly cause damage to the third party's life, body
or property.
(1) Aircraft equipment
(2) Aerospace equipment
(3) Undersea equipment
(4) Power plant control equipment
(5) Medical equipment
(6) Transportation equipment (vehicles, trains, ships, etc.)
(7) Traffic signal equipment
(8) Disaster prevention / crime prevention equipment
(9) Data-processing equipment
(10) Applications of similar complexity and / or reliability requirements
to the applications listed in the above.
MURATA MFG.CO.,LTD
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
