ACT26JD05SD [V001] datasheet, PDF

ACT26JD05SD [V001]: DescriptionSTRAIGHT PLUG; CategoryThe connector; File Size856KB，17 Pages; ManufacturerTE Connectivity; Websitehttp://www.te.com

Download Datasheet Parametric View All

ACT26JD05SD [V001] Overview

STRAIGHT PLUG

Parameter Name	Attribute value
Component type	electrical connector
Connector System	line to panel, line to panel
Sealable	yes
Connectors and terminals terminate to	Wires and cables
Housing size	15
shield	yes
Connector type	plug
Housing type	straight plug
Number of Positions	5
Number of power supply locations	5
Number of signal positions	0
Pre-installed	no
position keying	D
keying	Bond polarization D
Factory installed rear case	no
Operating voltage (VAC)	900
Voltage (Vrms)	2300
Operating voltage (VDC)	1250
Penetration type	no
Entrance method	Back penetration
Shell plating material	Cadmium, outer diameter
Shell material	composite
Insulation Materials	Hard dielectric/silica gel
Sealed	no
Fluid type	M2-V, MIL-DTL-5624 (JP-4,JP-5), MIL-DTL-83133 (JP-8), MIL-PRF-23699, MIL-PRF-5606, MIL-PRF-7808, SEA
Environmental protection type	Elastomeric seal
weight	16.8 g [ .0371 lb ]
environmental protection	yes
Contact Current Rating (Max) (A)	13
reverse polarity	no
Terminal layout	D05
Terminal type	socket
Number of terminals (size 16)	5
Panel mount features	Without
Connector mounting type	Panel
polar code	D
Joint alignment type	keying
joint fixation	with
Joint fixation type	Three-head thread
Location monitoring	Timing
Component length	31.5 mm [ 1.24 in ]
Cable size	.52 – 1.31 mm² [ 20 – 16 AWG ]
Acceptable wire insulation diameter range	1.65 – 2.77 mm [ .065 – .109 in ]
Working group temperature range	-65 – 200 °C [ -85 – 392 °F ]
fluid resistance	yes
Circuit Application	Power
Durability Level (Cycles)	500
Package quantity	1
Ignored load location	all

[Zhongke Bluexun AB32VG1 RISC-V board "runs into" RTT evaluation] Watchdog: [i=s]This post was last edited by xiyue521 on 2021-5-16 01:48[/i]The purpose of the watchdog is to protect the chip from entering an infinite loop (or the program running away). The watchdog has an in...; xiyue521 Domestic Chip Exchange

Voltage sampling is inaccurate: Voltage sampling is inaccurateWhen R10 is disconnected, the voltage division is accurate. When R10 is connected and sent to the ADC port of the MCU, the voltage division is inaccurate. The error is la...; QWE4562009 Discrete Device

About initialization problem: I would like to ask what is wrong with my initialization that causes the Bluetooth to not turn on the receiving function and report the error failed:0x48. Specifically, I would like to ask where the p...; 千本樱大白 ST - Low Power RF

Cost a few cents to DIY a charger: All the components were purchased from Taobao. As we all know, the Taobao Special Price APP is very suitable for buying these gadgets.MaterialEverything is here. The battery box and 4056 charging boar...; okhxyyo Power technology

EV2400 WIN7 64 BQ20Z45: Win7 64-bit, installed Bq20Z45R1, connected EV2400, the hardware properties show USB input device, can be updated to V0.28 through update. But the software reports an error, can not connect the batter...; qwqwqw2088 Analogue and Mixed Signal

Help: How to connect TST and RST of MSP430F6376 microcontroller? What are they used for?...; 曹伟1993 MCU

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components