Power Dissipation ...................................... Internally Limited
Lead Temperature (soldering, 5 seconds) .................. 260C
Storage Temperature Range ...................... -65C to +150C
Operating Junction Temperature Range ..... -40C to +125C
Input Supply Voltage ..................................................... +20V
ESD Rating .............................................................. 2kV min
ELECTRICAL CHARACTERISTICS
at V
IN
=V
OUT
+ 1.5V, T
A
= 25C, C
IN
= C
OUT
= 10F, unless otherwise specified. Limits in
Boldface
applies over the
full operating temperature range.
PARAMETER
2.5V Version
Output Voltage
3.0V Version
Output Voltage
3.3V Version
Output Voltage
All Output Options
Reference Voltage
Output Voltage
Temperature Stability
Line Regulation
CONDITIONS
I
OUT
= 10mA, V
IN
= 5.00V
0
≤I
OUT
≤600mA,
4.50V
≤V
IN
≤10V
I
OUT
= 10mA, V
IN
= 5.00V
0
≤I
OUT
≤600mA,
4.50V
≤V
IN
≤10V
I
OUT
= 10mA, V
IN
= 5.00V
0
≤I
OUT
≤600mA,
4.50V
≤V
IN
≤10V
I
OUT
=10mA, (V
IN
- V
OUT
) = 2V
10≤I
OUT
≤600mA,
1.4V
≤(V
IN
-V
OUT
)≤10V
(Note 1)
4.50V≤V
IN
≤12V,V
OUT
=3.00,I
OUT
=0
4.80V≤V
IN
≤12V,V
OUT
=3.30,I
OUT
=0
6.50V≤V
IN
≤12V,V
OUT
=5.00,I
OUT
=0
0≤I
OUT
≤600mA,V
IN
=4.50V,V
OUT
=3.00
0≤I
OUT
≤600mA,V
IN
=4.80V,V
OUT
=3.30
0≤I
OUT
≤600mA,V
IN
=6.50V,V
OUT
=5.0
I
L
=100mA
I
L
=600mA
4.25V≤V
IN
≤6.5V
(V
IN
-V
OUT
)=5V
25C, 30mS Pulse
f
RIPPLE
=120Hz, (V
IN
-V
OUT
)=3V,
V
RIPPLE
=1V
PP
125C, 1000Hrs
% of V
OUT
, 10Hz≤f≤10kHz
Junction to Case, at tab
TYP
2.475
2.450
2.970
2.940
3.267
3.234
1.238
1.225
MIN
2.500
MAX
2.525
2.550
3.030
3.060
3.333
3.366
1.262
1.270
0.05
UNITS
V
3.000
V
3.300
V
1.250
V
%
mV
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.05
5.00
50
.850
0.01
60
7.00
7.00
10.00
12.00
12.00
15.00
1.10
1.15
10.00
1.0
0.1
75
0.03
0.003
15
Load Regulation
mV
Dropout Voltage
(Note 2)
Quiescent Current
Adjust Pin Current
Current Limit
Thermal Regulation
Ripple Rejection
Long Term Stability
RMS Output Noise
Thermal Resistance
V
mA
A
A
%/W
dB
%
%
C/W
NOTES:
Note 1: Output temperature coefficient is defined as the worst case voltage change divided by the total temperature range.
Note 2: Dropout voltage is defined as the input to output differential at which the output voltage drops 100mV below its nominal value measured at 1V differential at
very low values of programmed output voltage, the minimum input supply voltage of 2V ( 2.3V over temperature) must be taken into account.
Note 3: Thermal regulation is defined as the change in output voltage at a time T after a change in power dissipation is applied excluding load or line regulation effect.
[i=s]This post was last edited by jinglixixi on 2020-12-20 11:15[/i]The visible light sensor AS7341 arrived as promised. After opening the large packaging box, a delicate black box magically appeared ...
Hello everyone:I don't understand a power switch circuit, so I came here to ask for your advice.I am planning to work on a project with a TFT screen recently. The picture below is the TFT screen power...
[i=s]This post was last edited by ohahaha on 2021-5-20 15:02[/i]The new infrastructure that conforms to the times includes: 5G infrastructure, ultra-high voltage, high-speed rail, new energy vehicle c...
1 IntroductionHigh-speed digital signal processor is one of the hot technologies in the current information industry. The use of the most advanced DSP will undoubtedly make the developed products more...
Say goodbye to 2018 and welcome 2019! I hope everyone will not dwell on the past, start a new journey, and ignite new hope! EEWorld celebrates the New Year with everyone....
Domestic Chip Exchange
京公网安备 11010802033920号
EEWORLD
