REVISION DR
DO NOT
SCALE FROM
THIS PRINT
NOTES:
1.
C
REPRESENTS A CRITICAL DIMENSION.
2. MINIMUM PUSHOUT FORCE: .5 LB.
C
3. COPLANARITY: .004[0.10] = POS 05 THRU 26
.006[0.15] = POS 27 THRU 50
4. TUBE ALL POSITIONS. PARTS TO BE TUBED WITH
NOTCH GOING WITH ARROW.
5. PINS CAN BE ORIENTED IN ANY DIRECTION;
BOTH ROWS MUST FACE SAME WAY.
6. SEE NOTCH FOR PROPER ORIENTATION.
C
7. MAXIMUM PIN HEIGHT VARIATION: .003[0.08]
FROM PIN TO PIN AND ROW TO ROW, MUST BE
MEASURED BETWEEN ADJACENT PINS.
8. DUE TO HIGH AMOUNT OF INSERTION FORCE
NEEDED, THE -LC OPTION IS NOT COMPATIBLE WITH
AUTO PLACEMENT. SAMTEC RECOMMENDS MANUAL
PLACEMENT FOR ALL ASSEMBLIES WITH THE -LC OPTION.
9. DIMENSION TO BE MEASURED AT BEND.
ANY CHANGES MADE TO THIS PRINT MUST ALSO BE MADE TO THE SFC PRINT
SFM-1XX-XX-XXX-D-XXX
No OF POSITIONS
ALL POSITIONS AVAILABLE
-02 THRU -50
(USE BODY: SFM-XX-D-XX-X)
LEAD STYLE
-01: THROUGH HOLE
(USE CONTACT: C-44-01-XXX)
(SEE FIG 1, SHT 1)
-02: SURFACE MOUNT
(USE CONTACT: C-44-02-XXX)
(SEE FIG 2, SHT 2)
-03: STRAIGHT MODIFIED
(USE CONTACT: C-44-03-XXX)
(SEE FIG 1, SHT 1)
-L1: THROUGH HOLE (LOW INSERTION)
(USE CONTACT: C-61-01-XXX)
(SEE FIG 1, SHT 1)
-L2: SURFACE MOUNT (LOW INSERTION)
(USE CONTACT: C-61-02-XXX)
(SEE FIG 2, SHT 2)
-L3: STRAIGHT MODIFIED (LOW INSERTION)
(USE CONTACT: C-61-03-XXX)
(SEE FIG 1, SHT 1)
-T1: THROUGH HOLE (PHOS BRONZE)
(USE CONTACT: C-119-01-XXX)
(SEE FIG 1, SHT 1)
-T2: SURFACE MOUNT (PHOS BRONZE)
(USE CONTACT: C-119-02-XXX)
(SEE FIG 2, SHT 2)
OPTIONS
(LEAVE BLANK FOR STANDARD
AND USE SFM-XX-D)
-N: NO POLARIZATION NOTCH
(USE SFM-XX-D-XX-N)
-A: ALIGNMENT PIN (USE SFM-XX-D-A-X)
(SEE FIG 4, SHT 2)
-LC: LOCKING CLIP (SEE FIG 6, SHT 3 & NOTE 8)
(AVAILABLE ON ALL LEADS)
-P: PICK AND PLACE PAD
(SEE FIG 5, SHT 2)
(AVAILABLE ON 5 THRU 50 POSITION ONLY)
-TR: TAPE & REEL (SEE SHT 4)
(NOT AVAILABLE WITH -DS OPTION)
-K: POLYIMIDE FILM PAD (.005[0.13] THICKNESS)
(SEE FIG 3, SHT 2) (USE K-DOT-.157-.250-.005)
-SN: SOLDER NAIL FOR .062 BOARD
(SFM-XX-D-SN AND WT-27-01-T)
(AVAILABLE WITH LEAD STYLE -02, -L2 & -T2)
(NOT AVAILABLE WITH -A & -LC)
-SN2: SOLDER NAIL FOR .093 BOARD
(SFM-XX-D-SN AND WT-27-02-T)
(AVAILABLE WITH LEAD STYLE -02, -L2 & -T2)
(NOT AVAILABLE WITH -A & -LC)
-DS: DUAL SCREW DOWN FOR .062 BOARD
(SEE FIG 8, SHT 3)
(ONLY AVAILABLE WITH -01, -02 AND -03 LEAD
STYLE)(NOT AVAILABLE WITH OPTIONS -N, -A,
-LC, -P, -TR, -K, -SN AND SN2), (USES SFM-XX-D-DS,
CPS-RR-XX-XX-X, ACCRT-01 AND WT-27-XX-T
ALWAYS FILLED)
BODY SPECIFICATION
-D: DOUBLE ROW
*DIMENSIONS N/A FOR -N OPTION
*.145 3.68 REF
*.020 0.51 REF
*.080 2.03 REF
.120 3.05 REF
.050 1.27
REF
02
C
L
C
L
01
.050 1.27 REF
(No OF POS x .050[1.27]) + .015[0.38] REF
"A"
C
L
(No OF POS x .050[1.27]) + .155[3.94] REF
SFM-XX-D-LC-X
C-XX-01-XXX
(SEE NOTE 5)
.110 2.79 REF
.180 4.57 REF
"A"
C
(SEE TABLE 1)
.015 0.38 REF
C
L
"A"
1 MAX SWAY
(EITHER DIRECTION)
"B" REF
(NO OF POS x .050[1.27]) - .050[1.27] REF
2 MAX SWAY
(EITHER DIRECTION)
.050 1.27
C
.005 0.13 REF
PLATING SPECIFICATION
-S: 30µ" SELECTIVE GOLD IN CONTACT AREA,
MATTE TIN ON TAIL
-F: 3µ" FLASH SELECTIVE GOLD IN CONTACT AREA,
MATTE TIN ON TAIL
-H: 30µ" HEAVY GOLD IN CONTACT AREA,
3µ" GOLD ON TAIL
-L: 10µ" LIGHT SELECTIVE GOLD IN CONTACT AREA,
MATTE TIN ON TAIL
-STL: 30µ" SELECTIVE GOLD IN CONTACT AREA,
TIN/LEAD (90/10+/-5%) TAIL
(ONLY AVAILABLE ON -02 OR -L2 LEADSTYLES)
-SM: 30µ" SELECTIVE GOLD IN CONTACT AREA,
MATTE TIN ON TAIL
-FM: 3µ" FLASH SELECTIVE GOLD IN CONTACT AREA,
MATTE TIN ON TAIL
-LM: 10µ" LIGHT SELECTIVE GOLD IN CONTACT AREA,
MATTE TIN ON TAIL
C
SECTION "A"-"A"
THIS DOCUMENT CONTAINS CONFIDENTIAL AND
PROPRIETARY INFORMATION AND ALL DESIGN,
MANUFACTURING, REPRODUCTION, USE, PATENT RIGHTS
AND SALES RIGHTS ARE EXPRESSLY RESERVED BY SAMTEC,
INC. THIS DOCUMENT SHALL NOT BE DISCLOSED, IN WHOLE
OR PART, TO ANY UNAUTHORIZED PERSON OR ENTITY NOR
REPRODUCED, TRANSFERRED OR INCORPORATED IN ANY
OTHER PROJECT IN ANY MANNER WITHOUT THE EXPRESS
WRITTEN CONSENT OF SAMTEC, INC.
THROUGH HOLE/STRAIGHT MODIFIED
FIG 1
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
DECIMALS
*
PROPRIETARY NOTE
*
.XX: .01 [0.3]
2
.XXX: .005 [0.13]
.XXXX: .0020 [0.051]
ANGLES
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail info@SAMTEC.com
code 55322
DESCRIPTION:
DWG. NO.
MATERIAL:
DO NOT SCALE DRAWING
SHEET SCALE: 3:1
INSULATOR: LCP UL 94V-O, COLOR: BLACK
CONTACT: TIGER EYE: BeCu
TIGER EYE LITE: PHOSPHOR BRONZE
F:\DWG\MISC\MKTG\SFM-1XX-XX-XXX-D-XXX-MKT.SLDDRW
.050 x .050 SOCKET STRIP DOUBLE ROW ASSEMBLY
BY:
JORDAN
SFM-1XX-XX-XXX-D-XXX
12/11/89
SHEET
1
OF
4
REVISION DR
(No OF POS x .050[1.27]) - .050[1.27] REF
(TOL ACCUM ±.005[0.13] OVER 50 POS)
"S"
C
(SEE NOTE)
"R"
(SEE NOTE)
C-XX-02-XXX
02
C
+.005
+0.13
.190
- .002
4.83
- 0.05
(SEE NOTE 9)
01
C
3 MAX SWAY
(EITHER DIRECTION)
IN-PROCESS
-X2
FOR HAND FILL ONLY
NOTE: DIMENSION APPLIES PRIOR
TO RE-PRESS, SEE SECTION "B"-"B"
FOR FINISHED DIMENSION
.019±.020 0.48±0.51
.1575±.0050 4.000±0.127
.190 4.83
-K: POLYIMIDE FILM PAD
(SAME AS FIG 1, DIFFERENT AS SHOWN)
NOTE: "R" = USED MEASURED DIMENSION REF
"S" = {("R" - .1575[4.000])/2}±.020[0.51]
FIG 3
"B"
SFM-XX-D-LC-X
C
.185
- .005
4.70
- 0.127
(SEE NOTES 7 & 9)
+.002
+0.051
4°
SEE NOTE 3
2°
"B"
SEE NOTE
SEE NOTE 7
-X2: SURFACE MOUNT
(SAME AS FIG 1, DIFFERENT AS SHOWN)
.394 10.01
REF
.225 5.72
REF
FIG 2
SEE NOTE 7
.161 4.09 REF
SECTION "B"-"B"
PPP-02
"A"±.010[0.25] (SEE TABLE 2)
.062 1.57
(NO. OF POS x .050[1.27]) + .125[3.18] REF
SFM-XX-D-A-X
.050 1.27
REF
.050 1.27
REF
R REF
(NO. OF POS x .050[1.27]) + .075[1.91] REF
-P: PICK AND PLACE PAD
(PAD TO BE ORIENTED A SHOWN FOR 5-12 POSITION PARTS)
(FOR 13-50 POSITION PARTS, PAD MAY BE ORIENTED IN EITHER DIRECTION)
(SAME AS FIG 1, DIFFERENT AS SHOWN)
THIS DOCUMENT CONTAINS CONFIDENTIAL AND
PROPRIETARY INFORMATION AND ALL DESIGN,
MANUFACTURING, REPRODUCTION, USE, PATENT RIGHTS
AND SALES RIGHTS ARE EXPRESSLY RESERVED BY SAMTEC,
INC. THIS DOCUMENT SHALL NOT BE DISCLOSED, IN WHOLE
OR PART, TO ANY UNAUTHORIZED PERSON OR ENTITY NOR
REPRODUCED, TRANSFERRED OR INCORPORATED IN ANY
OTHER PROJECT IN ANY MANNER WITHOUT THE EXPRESS
WRITTEN CONSENT OF SAMTEC, INC.
FIG 5
*
PROPRIETARY NOTE
*
-A: ALIGNMENT PIN
(SAME AS FIG 1, DIFFERENT AS SHOWN)
FIG 4
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail info@SAMTEC.com
code 55322
DESCRIPTION:
DWG. NO.
DO NOT SCALE DRAWING
SHEET SCALE: 3:1
.050 x .050 SOCKET STRIP DOUBLE ROW ASSEMBLY
F:\DWG\MISC\MKTG\SFM-1XX-XX-XXX-D-XXX-MKT.SLDDRW
BY:
JORDAN
SFM-1XX-XX-XXX-D-XXX
12/11/89
SHEET
2
OF
4
REVISION DR
SFM-XX-D-LC-X
(NO OF POS x .050[1.27] + .360[9.14]
C
.065 1.65
.056 1.42 REF
2 MAX SWAY
(EITHER DIRECTION)
2 MAX SWAY
LC-05-TM
(EITHER DIRECTION)
.010 0.25 REF
.218 5.52
REF
02
(NO OF POS x .050[1.27] + .075[1.91] REF
-LC: LOCKING CLIP
(SAME AS FIG 1, DIFFERENT AS SHOWN)
(AVAILABLE IN ALL LEADS)
CPS-RR-M2-01-X
FIG 6
01
'E'
C
.145 3.68
.335 8.50
REF
.070 1.78
REF
SFM-XX-D-DS
"D"
C
WT-27-XX-T
(NO OF POS x .050[1.27] + .600[15.24] REF
.114 2.90 REF
ACCRT-01
.012 0.30
REF
(NO OF POS x .050[1.27] + .185[4.70] REF
SFM-XX-D-SN
"C"
C
FLUSH TO .005[0.13] ABOVE
DETAIL 'E'
SCALE 6 : 1
-DS: DUAL SCREW DOWN
(SAME AS FIG 2, DIFFERENT AS SHOWN)
FIG 8
"C" REF
WT-27-XX-T
"C"
2 MAX SWAY
(EITHER DIRECTION)
(NO OF POS x .050[1.27] + .085[2.16] REF
.026 0.66
REF
SECTION "C"-"C"
THIS DOCUMENT CONTAINS CONFIDENTIAL AND
PROPRIETARY INFORMATION AND ALL DESIGN,
MANUFACTURING, REPRODUCTION, USE, PATENT RIGHTS
AND SALES RIGHTS ARE EXPRESSLY RESERVED BY SAMTEC,
INC. THIS DOCUMENT SHALL NOT BE DISCLOSED, IN WHOLE
OR PART, TO ANY UNAUTHORIZED PERSON OR ENTITY NOR
REPRODUCED, TRANSFERRED OR INCORPORATED IN ANY
OTHER PROJECT IN ANY MANNER WITHOUT THE EXPRESS
WRITTEN CONSENT OF SAMTEC, INC.
*
PROPRIETARY NOTE
*
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail info@SAMTEC.com
code 55322
DESCRIPTION:
DWG. NO.
-SNX: SOLDER NAIL
(SAME AS FIG 1, DIFFERENT AS SHOWN)
F:\DWG\MISC\MKTG\SFM-1XX-XX-XXX-D-XXX-MKT.SLDDRW
FIG 7
DO NOT SCALE DRAWING
SHEET SCALE: 3:1
.050 x .050 SOCKET STRIP DOUBLE ROW ASSEMBLY
SFM-1XX-XX-XXX-D-XXX
12/11/89
SHEET
3
OF
4
BY:
JORDAN
REVISION DR
PT-1-24-13-09
.630 16.00
PT-SFM004-X1-X3-D
PT-SFM004-X1-X3-D
PT-1-24-01-60
2.205 56.00
"D"
"D"
UNWINDING DIRECTION
*FOR MACHINE LOADING OF TUBES FOR PARTS W/O PADS USE PT-1-24-14-09, TP-24-02
5 POS -01 AND -03 LEAD STYLES MAY BE TUBED USING PT-1-24-15-09, TP-24-02
2 POS -X1 STYLE TO BE TUBED IN PT-1-24-15-09
(SEE NOTE 6)
PACKAGE PARTS IN TUBES AS SHOWN (SEE NOTE 4)
PACKAGING VIEW
SECTION "D"-"D"
SCALE 2 : 1
PACKAGING VIEW
-TR: TAPE AND REEL
F:\DWG\MISC\MKTG\SFM-1XX-XX-XXX-D-XXX-MKT.SLDDRW
*
PROPRIETARY NOTE
*
THIS DOCUMENT CONTAINS CONFIDENTIAL AND
PROPRIETARY INFORMATION AND ALL DESIGN,
MANUFACTURING, REPRODUCTION, USE, PATENT RIGHTS
AND SALES RIGHTS ARE EXPRESSLY RESERVED BY SAMTEC,
INC. THIS DOCUMENT SHALL NOT BE DISCLOSED, IN WHOLE
OR PART, TO ANY UNAUTHORIZED PERSON OR ENTITY NOR
REPRODUCED, TRANSFERRED OR INCORPORATED IN ANY
OTHER PROJECT IN ANY MANNER WITHOUT THE EXPRESS
WRITTEN CONSENT OF SAMTEC, INC.
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail info@SAMTEC.com
code 55322
DESCRIPTION:
DWG. NO.
DO NOT SCALE DRAWING
SHEET SCALE: 1.5:1
.050 x .050 SOCKET STRIP DOUBLE ROW ASSEMBLY
SFM-1XX-XX-XXX-D-XXX
12/11/89
BY:
JORDAN
SHEET
4
OF
4
Motor Drive Control（Motor Control）
京公网安备 11010802033920号
EEWORLD
