EEWORLDEEWORLDEEWORLD

Part Number

Search

270V824A501B1A1

Description
Commercial Miniature 5/8 (16mm) Diameter Composition Variable Resistors
File Size1MB,6 Pages
ManufacturerCTS [CTS Corporation]
Download Datasheet View All

270V824A501B1A1 Overview

Commercial Miniature 5/8 (16mm) Diameter Composition Variable Resistors

270V824A501B1A1 Preview

Series 270
®
Commercial
Miniature 5/8"
(16mm) Diameter
Composition
Variable Resistors
• Miniature 5/8" (16mm) size
• Versatile mounting styles:
– bushing
– twist tab
– bend tab
– snap-in PC bracket
– solder lug or PC terminals
(shaft parallel or perpendicular to the panel)
• 100
to 5 Meg
resistance range
• Molded or metal shafts
• SPST power switches
• Single, tandem, or concentric units
• Panel seal
• Rear extended shaft
Electrical and Mechanical Specifications
Resistance Range
100
through 5 Meg
(linear taper).
Resistance Tolerance
Standard: ±20%
Special: Other tolerances available in most
resistance values.
Power Rating, Watts
1
/
4
watt per section through 100K
1
/
5
watt per section above 100K
Full rating @ 55°C derated to no load at 85°C,
linear taper, bushing mounted control on steel panel
4" x 4" x .050" (101.6mm x 101.6mm x 1.27mm).
(Derating required on two section controls.)
Voltage Rating
Bushings to Terminals:
High pot test, one minute — 750 VAC
Operating maximum
— 500 VDC
Across End Terminals:
350 VDC, load not to exceed listed wattage ratings.
Resistance Tapers
Standard: Linear, 10% Audio and 10% CCW Audio
Special tapers available to meet most requirements
Angle of Rotation
Total Rotation
Without Switch: 300° ± 5°
With Switch:
315° ± 5°
Effective Rotation
Without Switch: 300° (approximate)
With Switch:
290° (approximate)
Panel Mounting Information
Bushing Mount
Standard: Brass
(continued on next page)
Technical Data Sheet 1448C
Technical Data Sheet 1270E
CTS CORPORATION /
MANUFACTURER OF RELIABLE ELECTRONIC COMPONENTS
Electrical and Mechanical Specifications
(continued)
All Other Mounts
Standard: Twist tab (designated by “1”)
Special: Bend tab — 2 or 3 ears
Bracket mounted
Suggested Panel for Twist Tab
.042" thick (1.07mm)
Locating Lugs (Bushing Mount)
Standard: .312" (7.9mm) radius from center of control.
Special: .375" (9.53mm) radius from center of control.
Standard Position: Left side supplied unless otherwise
specified.
Other Positions:
Available with lug right side,
without lugs, or with lugs both
left and right sides.
Water Seal Construction
Controls are also available to prevent water
from entering the control through either the
O.D. of shaft and/or the bushing.
Concentric Tandem Units
Available in two combinations:
A
– .125" (3.2mm) diameter rear shaft
.250" (6.35mm) panel shaft
(3/8 – 32 or M9X.75)
B
– .156" (4.0mm) diameter rear shaft
.236" (6.0mm) diameter panel shaft
(3/8 – 32 or M8X.75)
Most metal shaft diameters can be used with
twist tab mountings. With bracket mount,
only .187 diameter shafts are used, with turn-down
available to obtain smaller diameters.
Metal
Lengths: Minimum .125" (3.2mm) beyond bushing;
special lengths as required.
Trims:
Plain round screwdriver slotted, flatted,
knurled. Other trims available
upon request.
Molded
Flatted and knurled with screwdriver slot available
in many lengths and diameters.
Terminal Information
Standard: T Solder lug formed 90° to the rear.
Special:
(See below)
T:
T:
U:
Solder lug perpendicular to shaft.
Solder lug formed 60° to the rear.
PC terminals formed 90° forward toward
mounting surface. Terminals extend .187"
(4.7mm) beyond mounting surface.
PC terminals formed 90° to the rear, away
from panel mounting. Terminals extend .520"
(13.2mm) from mounting surface.
Shaft and Bushing Information
Bushing Lengths Available
Standard: .187" or .250" (4.75mm or 6.35mm)
Special: .125" increments (3.2mm increments)
Thread Size
Standard:
1
/
4
" – 32
3
/
8
" – 32
M7 x .75
M8 x .75P
Special: As required
Molded Shafts Available
(Shown with preferred diameter bushing)
Bushing Mounted or Ear Mounted
SHAFT DIAMETER
INCH
.156
.187
.236
.250
MM
4.0
4.7
6.0
6.35
BUSHING DIAMETER
INCH
1/4" – 32
3/8" – 32
3/8" – 32
MM
M7X.75
M7X.75
M8X.75
M9X.75
V:
W: Wire wrap terminals — .156" (4.0mm) terminal
extension beyond base, formed 60° to the rear.
BX: PC terminals standard .438" (11.1mm) from
center line of control to PC board; straight
terminals extend .156" (4.0mm) into PC board.
X:
PC terminals standard .505" (12.8mm) from
center line of control to PC board, with .136"
(3.4mm) straight terminal extension beyond
PC board standoff.
PC terminals standard .602" (15.3mm) from
centerline of control to PC board, with .140"
(3.5mm) straight terminal extension beyond
PC board standoff.
Metal Shafts Available
(Shown with preferred diameter bushing)
Single or Dual Units
SHAFT DIAMETER
INCH
.125
.156
.187
.236
.250
MM
3.2
4.0
4.7
6.0
6.35
BUSHING DIAMETER
INCH
1/4" – 32
1/4" – 32
3/8" – 32
3/8" – 32
3/8" – 32
MM
M7X.75
M7X.75
M7X.75
M8X.75
M9X.75
Y:
(continued on next page)
Electrical and Mechanical Specifications
(continued)
Power Switches Available
(all SPST)
SERIES
057
057
TYPE
Rotary
Rotary
ELECTRICAL
RATING
5A @ 20 VDC
3A @ 125 VAC
(UL approved)
Switch Actuating Angle -25˚
Switch Actuating Torque - 2 to 10 in. oz.
(144 to 720g-cm)
DIMENSION:
MM
INCH
SERIES
DEMI
DEMI
TYPE
Push-Pull
Momentary contact
Push on
ELECTRICAL
RATING
3A @ 20 VDC
3A @ 20 VDC
DIMENSION:
MM
INCH
T270
Solder Lug Terminals, Metal Shaft, Bushing Mount
DIMENSION:
MM
INCH
BX PM270
PC Type Base “X” Terminals, 2-Ear Mount Bend Tab, Molded Shaft
DIMENSION:
MM
INCH
UPE 270RE
PC Type “U” Terminals, Twist Tab Mount, Metal Shaft, Rear Extension
DIMENSION:
MM
INCH
XB275RE
PC Type “X” Terminals, Metal Shaft, Rear Extension
DIMENSION:
MM
INCH
VPE 270
PC Type “V” Terminals, Twist Tab Mount, Metal Shaft
DIMENSION:
MM
INCH
X057-BX270
PC Type Terminal SPST Switch, PC Style Base “X” Terminals, Metal Shaft, Bushing Mount
DIMENSION:
MM
INCH
T2-270
Solder Lug Terminals, Straight Tandem, Metal Shaft, Bushing Mount
DIMENSION:
MM
INCH
XP275
PC Type “X” Terminal, Metal Shaft, Twist Tab Mounting
DIMENSION:
MM
INCH
FPGA Learning Notes-----FPGA Competition Adventure
...
至芯科技FPGA大牛 FPGA/CPLD
Analysis of the role of terminal resistance in CAN bus
The editor would like to remind you that when using the CAN bus, whether in the process of product development or network construction, it is necessary to arrange the terminal resistance on the bus re...
MamoYU Integrated technical exchanges
Serial communication: 8051 and 8051 point-to-point communication
-----------Send from machine A------ ORG 0000H LJMP MIAN ORG 0023H LJMP SERVE1 ORG 2000HMAIN:MOV TMOD,#20H MOV TH1,#0F3H MOV TL1,#0F3H SETB TR1 MOV PCON ,#80H MOV SCON,#0D0H MOV DPTR,#4000H MOV R0,#80...
rain 51mcu
Download the information and watch the video to win a prize | Tektronix HDMI 2.1 test solution is now available for download, and you can also watch the supporting video
Recently, Tektronix's FRL TX, FRL RX and eARC TX/RX test solutions have all been approved by the HDMI Association! Want to know more about the test solutions? Come and participate in the event to down...
EEWORLD社区 Test/Measurement
Things to note when using C/C++ to write programs based on TMS320 series DSP
[size=4][font=微软雅黑, 宋体]1. Without affecting the execution speed, you can use the function library provided by C or C/C++ language, or you can design your own function, which is easier to use the "tail...
fish001 DSP and ARM Processors
Generate sine wave data using microcontroller DAC and C language
The following is applicable to all types of microcontrollers:  Changing the DAC output voltage of the microcontroller can get the required voltage waveform output. The following describes how to calcu...
fish001 DSP and ARM Processors

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号