EEWORLDEEWORLDEEWORLD

Part Number

Search

AEQ75Y48-L

Description
DC-DC Regulated Power Supply Module, 1 Output, 135W, Hybrid, ROHS COMPLIANT
CategoryThe power supply circuit   
File Size164KB,2 Pages
ManufacturerVertiv
Environmental Compliance
Download Datasheet Parametric View All

AEQ75Y48-L Overview

DC-DC Regulated Power Supply Module, 1 Output, 135W, Hybrid, ROHS COMPLIANT

AEQ75Y48-L Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerVertiv
package instruction,
Reach Compliance Codeunknown
ECCN codeEAR99
Is SamacsysN
Analog Integrated Circuits - Other TypesDC-DC REGULATED POWER SUPPLY MODULE
Maximum input voltage75 V
Minimum input voltage36 V
Nominal input voltage48 V
JESD-30 codeR-XXMA-P10
JESD-609 codee3
Number of functions1
Output times1
Number of terminals10
Maximum operating temperature105 °C
Minimum operating temperature-40 °C
Maximum output voltage1.98 V
Minimum output voltage1.62 V
Nominal output voltage1.8 V
Package body materialUNSPECIFIED
Package shapeRECTANGULAR
Package formMICROELECTRONIC ASSEMBLY
Peak Reflow Temperature (Celsius)NOT SPECIFIED
Certification statusNot Qualified
surface mountNO
technologyHYBRID
Temperature levelINDUSTRIAL
Terminal surfaceTIN OVER NICKEL
Terminal formPIN/PEG
Terminal locationUNSPECIFIED
Maximum time at peak reflow temperatureNOT SPECIFIED
Maximum total power output135 W
Fine-tuning/adjustable outputYES
Base Number Matches1
Astec Industry Standard
75 Amps
AEQ75Y48
High Efficiency Quarter Brick
Total Power:
Input Voltages:
No. of Outputs:
135W
48V
Single
Electrical Specs
Input
Input Range
Input Surge
Efficiency
36 to 75 VDC
100V /100ms
89% typical
Output
Output Current
Line/Load Regulation
Noise/Ripple
Remote sense
Transient Response
75A max
<0.15%Vo typical
25mV typical
Up to 10% of Vo
4% deviation typical
50% to 75% Load change
0.1A/µs Slew Rate
100µs recovery
120% Vo (autorecovery)
110% Io (autorecovery)
500kHz
Special Features
High Efficiency
Baseplate construction
Industry standard package 1.45" x 2.30"
Redundant output power pins
Startup and stable operation at high
capacitive load
Remote sense compensation
Regulation to zero load
Fixed frequency switching
Basic insulation
EU Directive 2002/95/EC Compliant for RoHS
Overvoltage Protection
Current Limit
Switching Frequency
Control
Voltage Adjust
Enable
90 to 110% Vo
TTL compatible
(Positive or Negative Logic options)
Environmental
Operating temperature range:
-40°C to +105°C Baseplate
Storage temperature: -40°C to +125°C
Overtemperature protection: 115°C PCB
temperature (Typical)
MTBF: > 1 million hours
Safety
UL, cUL 60950
TUV
EN60950
1
North America (USA): 1-888-41-ASTEC
Europe (UK): 44 (1384) 842-211
Asia (HK): 852-2437-9662
Goodbye 2019, hello 2020!
Goodbye 2019, hello 2020! In 2019, I found my own direction of struggle. Because of this direction of struggle, I got to know the Electronic Engineering Welfare Club. In the Electronic Engineering Wel...
果轩天 Talking
SensorTile.box unpacking issues
[i=s]This post was last edited by KJGL on 2020-4-18 09:18[/i]At first, I followed the tutorial and when I updated the firmware in the APP, the Bluetooth connection with the board was disconnected. I q...
KJGL ST MEMS Sensor Creative Design Competition
Are the EX0 bit in the IE register and the IE0 bit in the TCON register in the 51 microcontroller duplicated?
I would like to ask whether the EX0 bit in the IE register of the 51 single-chip microcomputer and the IE0 bit in the TCON register are repeated. From the information in the figure below, aren't these...
一沙一世 51mcu
Detailed diagram of microwave oven capacitor connection
There are two ways to judge whether a high-voltage capacitor is good or bad.  1. Detection and judgment when there is no power: Use a meter to measure the resistance. The resistance of the primary end...
Aguilera Analogue and Mixed Signal
The execution time limit has been exceeded. Please check whether there is an infinite loop or the program algorithm is inefficient.
[i=s] This post was last edited by bqgup on 2021-8-24 21:05 [/i] #Running exceeds the time limit, please check whether there is an infinite loop or the program algorithm is inefficient? ##Requirement ...
bqgup Innovation Lab
How to configure external FLASH in FX3/CX3(CYUSB3065)
I am using (CYUSB3065) and a 16M FLASH is attached to the outside of the chip. Currently, there is no problem with burning and starting, but when I try to modify the space configuration, it cannot be ...
jacky2019 EE_FPGA Learning Park

Technical ResourceMore

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号