EEWORLDEEWORLDEEWORLD

Part Number

Search

TMM-108-06-L-S-SM-P

Description
2MM TERMINAL STRIP
CategoryThe connector    The connector   
File Size18KB,1 Pages
ManufacturerSAMTEC
Websitehttp://www.samtec.com/
Environmental Compliance
Download Datasheet Parametric View All

TMM-108-06-L-S-SM-P Overview

2MM TERMINAL STRIP

TMM-108-06-L-S-SM-P Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Reach Compliance Codecompliant
ECCN codeEAR99
Factory Lead Time2 weeks
body width0.078 inch
subject depth0.109 inch
body length0.632 inch
Connector typeBOARD CONNECTOR
Contact to complete cooperationGOLD (15)
Contact completed and terminatedTin (Sn) - with Nickel (Ni) barrier
Contact point genderMALE
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
DIN complianceNO
Filter functionNO
IEC complianceNO
Insulator colorBLACK
insulator materialLIQUID CRYSTAL POLYMER (LCP)
JESD-609 codee3
MIL complianceNO
Manufacturer's serial numberTMM-1
Plug contact pitch0.079 inch
Mixed contactsNO
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number2
Number of rows loaded1
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
OptionsGENERAL PURPOSE
PCB contact patternSTAGGERED
PCB contact row spacing2.032 mm
Plating thickness10u inch
Rated current (signal)3.2 A
GuidelineUL, CSA
reliabilityCOMMERCIAL
Terminal pitch2 mm
Termination typeSURFACE MOUNT
Total number of contacts8
UL Flammability Code94V-0
Base Number Matches1
About the compilation speed when compiling STM32 with MDK
The most commonly used compilers for developing STM32F are generally MDK and IAR. IAR is relatively simple and has slightly better compilation efficiency. MDK simulation effect is better, and most peo...
懒猫爱飞 stm32/stm8
Auto repair oscilloscope measuring the oxygen sensor signal of the car zirconium oxygen belt heater
Last time we talked about using an oscilloscope to measure the signal of the car's air flow meter. This time we will talk about using an oscilloscope to measure the car's oxygen sensor. The oxygen sen...
Micsig麦科信 Test/Measurement
Can the same-phase AC amplifier circuit be used for low frequencies?
[align=left][font=微软雅黑][size=12.0pt]The capacitor Ci next to R4 is equivalent to an open circuit for DC, so the DC component is not amplified; it is equivalent to a short circuit for AC, so the AC amp...
sfcsdc Analog electronics
Summary: Reading notes on "Operational Amplifier Parameter Analysis and LTspice Application Simulation"
Activity details: Read the good book "Operational Amplifier Parameter Analysis and LTspice Application Simulation" for free, take notes, and thoroughly master the knowledge of operational amplifiersSu...
okhxyyo Analog electronics
How to use CPLD to collect asynchronous signals
Scenario: Use CPLD to decode a serial data channel. The data has no accompanying clock and has a fixed frequency but a different single-bit phase. My idea: I want to realize the acquisition of asynchr...
XCXBD EE_FPGA Learning Park
Share: Where should the inductor be placed on the power supply PCB?
[size=4]First, let’s ask the question: where should the coil be placed? [/size] [size=4] [/size] [size=4] Switching regulators for voltage conversion use inductors to temporarily store energy. These i...
qwqwqw2088 Analogue and Mixed Signal

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号