EEWORLDEEWORLDEEWORLD

Part Number

Search

AM1D-1205DH30-N

Description
1 watt dc-dc converters
CategoryAnalog mixed-signal IC    The signal circuit   
File Size488KB,3 Pages
ManufacturerAimtec
Websitehttp://www.aimtec.ca/
Download Datasheet Parametric View All

AM1D-1205DH30-N Overview

1 watt dc-dc converters

AM1D-1205DH30-N Parametric

Parameter NameAttribute value
MakerAimtec
package instruction,
Reach Compliance Codeunknow

AM1D-1205DH30-N Preview

AM1D-N Series
1 watt dc-dc converters
7PIN SIP PACKAGE
LOW RIPPLE & NOISE
HIGH EFFICIENCY UP TO 81%
UL94-VO PACKAGE
INPUT/OUTPUT ISOLATION: 1000, 3000 & 6000VDC
OPERATING TEMPERATURE: -40°C ... +85°C
PIN-COMPATIBLE WITH MULTIPLE MANUFACTURERS
GENERAL DESCRIPTION
Our AM1D-N series is a family of cost effective 1W
single, dual output isolated DC-DC converters. These con-
verters achieve low cost and ultra-miniature SIP7 pin size
without compromising performance and reliability.
Seventy two models operate from input voltages of 5, 12
& 24VDC; producing output voltage levels of 5, 9, 12, 15, ±5,
±9, ±12, ±15VDC. Full SMD-design and a 100% production
test of parameters ensures a high reliability in this product.
ELECTRICAL SPECIFICATIONS
Specifications typical at +25°C, nominal input voltage, rated output current unless otherwise specified
Input Specifications:
Voltage range
Filter
Isolation Specifications:
Rated voltage (60 sec)
Resistance
Capacitance
±10%
Capacitor
1000, 3000 & 6000VDC
> 1000MOhm
60pF, typ.
General Specifications:
Efficiency
Switching frequency
72% to 81%
150KHz, typ. 100% load
Output Specifications:
Voltage balance (dual output) ±1%
Voltage accuracy
±5%, max.
Ripple & noise (at 20MHz BW) 75mVp-p, typ.
Short circuit protection
1 sec.
Line voltage regulation
±1.2% / 1.0% of Vin
Load voltage regulation
10% max.
load=10~100%
Temperature coefficient
±0.03%/°C, max.
Specifications are subject to change without notification
Environmental Specifications:
Operating temperature (ambient) -40°C ... +85°C
Storage temperature
-55°C ... +125°C
Case Temperature
+95°C, max.
Derating
None required
Humidity (non-condensing)
Up to 90%
Cooling
Free-air Convection
Physical Specifications:
Dimensions
(1000 & 3000VDC)
19.50x6.00x10.00mm
0.76x0.24x0.39inches
Dimensions
(6000VDC)
19.50x9.8x12.5mm
0.76x0.39x0.49inches
Weight
2g
Case material
Plastic UL94-VO
MTBF: > 1,100,000 hrs (MIL-HDBK-217F, Ground Benign, t=+25°C)
PIN CONNECTIONS
Pin
Single
1000VDC
Dual
3000, 6000VDC
Single
Dual
1
2
4
5
6
7
+V Input
-V Input
-V Output
Omitted
+V Output
Omitted
+V Input
-V Input
-V Output
Common
+V Output
Omitted
+V Input
-V Input
Omitted
-V Output
Omitted
+V Output
+V Input
-V Input
Omitted
-V Output
Common
+V Output
Continued on next page
17
VISIT US AT WWW.AIMTEC.CA
AM1D-N Series
OUTLINE DIMENSIONS
1000 & 3000VDC
6000VDC
9.8
(0.39)
12.5
(0.49)
12.5
(0.49)
DC-DC CONVERTERS
9.8
(0.39)
MODELS
Single output
Models
Isolation 1000VDC Isolation 3000VDC Isolation 6000VDC
AM1D-0505S-N
AM1D-0509S-N
AM1D-0512S-N
AM1D-0515S-N
AM1D-1205S-N
AM1D-1209S-N
AM1D-1212S-N
AM1D-1215S-N
AM1D-2405S-N
AM1D-2409S-N
AM1D-2412S-N
AM1D-2415S-N
Dual output
Models
Isolation 1000VDC Isolation 3000VDC Isolation 6000VDC
AM1D-0505D-N
AM1D-0509D-N
AM1D-0512D-N
AM1D-0515D-N
AM1D-1205D-N
AM1D-1209D-N
AM1D-1212D-N
AM1D-1215D-N
AM1D-2405D-N
AM1D-2409D-N
AM1D-2412D-N
AM1D-2415D-N
AM1D-0505DH30-N AM1D-0505DH60-N
AM1D-0509DH30-N AM1D-0509DH60-N
AM1D-0512DH30-N AM1D-0512DH60-N
AM1D-0515DH30-N AM1D-0515DH60-N
AM1D-1205DH30-N AM1D-1205DH60-N
AM1D-1209DH30-N AM1D-1209DH60-N
AM1D-1212DH30-N AM1D-1212DH60-N
AM1D-1215DH30-N AM1D-1215DH60-N
AM1D-2405DH30-N AM1D-2405DH60-N
AM1D-2409DH30-N AM1D-2409DH60-N
AM1D-2412DH30-N AM1D-2412DH60-N
AM1D-2415DH30-N AM1D-2415DH60-N
Input
Voltage
5V±10%
Input
Voltage
5V±10%
Ouput
Voltage
5VDC
9VDC
12VDC
15VDC
5VDC
9VDC
12VDC
15VDC
5VDC
9VDC
12VDC
15VDC
Ouput
Current max.
200mA
110mA
83mA
70mA
200mA
110mA
83mA
70mA
200mA
110mA
83mA
70mA
AM1D-0505SH30-N
AM1D-0509SH30-N
AM1D-0512SH30-N
AM1D-0515SH30-N
AM1D-1205SH30-N
AM1D-1209SH30-N
AM1D-1212SH30-N
AM1D-1215SH30-N
AM1D-2405SH30-N
AM1D-2409SH30-N
AM1D-2412SH30-N
AM1D-2415SH30-N
AM1D-0505SH60-N
AM1D-0509SH60-N
AM1D-0512SH60-N
AM1D-0515SH60-N
AM1D-1205SH60-N
AM1D-1209SH60-N
AM1D-1212SH60-N
AM1D-1215SH60-N
AM1D-2405SH60-N
AM1D-2409SH60-N
AM1D-2412SH60-N
AM1D-2415SH60-N
12V±10%
24V±10%
Ouput
Voltage
±5VDC
±9VDC
±12VDC
±15VDC
±5VDC
±9VDC
±12VDC
±15VDC
±5VDC
±9VDC
±12VDC
±15VDC
Ouput
Current max.
±100mA
±55mA
±42mA
±35mA
±100mA
±55mA
±42mA
±35mA
±100mA
±55mA
±42mA
±35mA
12V±10%
24V±10%
18
TO ORDER CALL 1-888-9-AIMTEC
AM1D-N Series
TYPICAL CHARACTERISTICS
+5%
APPLICATION NOTE
Filtering
In some circuits which are sensitive to noise and ripple, a filtering capacitor may be added to the DC/DC output end and input end to reduce the noise
and ripple. However, the capacitance of the output filter capacitor must be proper. If the capacitance is too big, a startup problem might arise. For every
channel of output, provided the safe and reliable operation is ensured, the greatest capacitance of its filter capacitor sees the external capacitor table. To
get an extremely low ripple, an “LC” filtering network may be connected to the input and output ends of the DC/DC converter, which may produce a more
significant filtering effect. It should also be noted that the inductance and the frequency of the “LC” filtering network should be staggered with the dc/dc
frequency to avoid mutual interference (see figure 1).
Requirement on output load
To ensure this module can operate efficiently and reliably, a minimum load is specified for this kind of DC/DC converter in addition to a maximum load
(namely full load). During operation, make sure the specified range of input voltage is not exceeded, the minimum output load is not less than 10% of the
full load, and that this product should never be operated under no load! If the actual output power is very small, please connect a resistor with proper
resistance at the output end in parallel to increase the load.
For single output
Overload Protection
Under normal operating conditions, the output
circuit of these products has no protection
against over-current and short-circuits. The
simplest method is to connect a self-recovery
fuse in series at the input end or add a circuit
breaker to the circuit.
Output Voltage Regulation and
Over-voltage Protection Circuit
The simplest device for output voltage
regulation, over-voltage and over-current
protection is a linear voltage regulator with
overheat protection that is connected to the
input or output end in series (see Figure 2).
For dual output
<Figure 1>
<Figure 1>
<Figure 2>
<Figure 2>
External Capacitor Table
for Single Output
Vin
External
Capacitor
Vout
External
Capacitor
External Capacitor Table
for Dual Output
Vin
External
Capacitor
Vout
External
Capacitor
5VDC
12VDC
24VDC
-
4.7uF
2.2uF
1uF
-
5VDC
9VDC
12VDC
15VDC
10uF
4.7uF
2.2uF
1uF
5VDC
12VDC
24VDC
-
4.7uF
2.2uF
1uF
-
5VDC
9VDC
12VDC
15VDC
4.7uF
2.2uF
1uF
0.47uF
19
VISIT US AT WWW.AIMTEC.CA
The Structure and Interpretation of Computer Programs (2nd Edition)
This book was one of the introductory course materials for the computer science major at the Massachusetts Institute of Technology. It explains the creation, execution, and study of computer programs ...
arui1999 Download Centre
Teacher maychang's new work - interesting video about the history of electronic technology: the debate between AC and DC
In 1831, Faraday discovered the law of electromagnetic induction, and the following year, French scientist Pixy invented the world's first generator based on the law of electromagnetic induction. It w...
EE大学堂 maychang Fun Electronics
Detailed description of the debugging document of the NUCLEO-G431RB+IHM08-V4 three-resistor FOC (5.4.1 library) motor control board
This content is originally created by music_586 , a user of EEWORLD forum. If you want to reprint or use it for commercial purposes, you need to obtain the author's consent and indicate the sourceST F...
music_586 stm32/stm8
Pybricks: MicroPython for LEGO
Translated from: https://forum.micropython.org/viewtopic.php?t=8569p=48511#p48511 Hello everyone - we are excited to share a new MicroPython family with you: Pybricks.Pybricks brings MicroPython to al...
dcexpert MicroPython Open Source section
STM32 environment construction under MDK compiler
I want to learn how to develop STM32 in C language recently. When I use MDK to build the environment, the compilation fails. I am a newbie, so please give me some advice. The first compilation error: ...
xuanyuanzhu stm32/stm8
[RVB2601 Creative Application Development] 6 score display, score +1 after eliminating letters
In the previous issue, we eliminated letters. This time, we added a fraction lvgl control based on this. So we need a variable to record the score: int score=0;//分数初始为0 There is also a label tag: lv_o...
cybertovsky XuanTie RISC-V Activity Zone

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号