RN73H
high heat resistance, high reliability
metal film chip resistor
EU
features
•
High precision type ±0.05% is available
with standard products
•
Improved moisture resistance by glass passivation layer
•
High reliability and high stability at elevated temperatures
•
Low current noise
•
Products with lead-free terminations meet
EU RoHS requirements
•
Rated ambient temperature: 85°C, rated up to +155°C
•
AEC-Q200 Qualified: 0402 (1E), 0603 (1J), 0805 (2A),
1206 (2B), 1210 (2E)
dimensions and construction
c
L
c
% Rated Power
% Rated Power
resistors
Type
(Inch Size Code)
L
.039
+.004
-.002
+0.1
)
(1.0
-0.05
Dimensions
inches
(mm)
W
c
d
.020±.002 .010±.004 .010
(0.5±0.05) (0.25±0.1) (0.25
+.002
-.004
+0.05
)
-0.1
t
.014±.002
(0.35±0.05)
1E
(0402)
W
Solder
Plating
Ni
Plating
d
Protective
Coating
Resistive Inner
Electrode
Film
1J
(0603)
2A
(0805)
2B
(1206)
2E
(1210)
100
80
60
40
20
0
-60 -40
-55
.063±.008 .031±.004 .012±.004 .012±.004 .018±.004
(1.6±0.2)
(0.8±0.1)
(0.3±0.1) (0.45±0.1)
(0.3±0.1)
.079±.008 .049±.008 .016±.008
(2.0±0.2) (1.25±0.2) (0.4±0.2)
.063±.008
.126±.008
(1.6±0.2)
(3.2±0.2)
.098±.008
(2.5±0.2)
.02±.012
(0.5±0.3)
.012
(0.3
.016
(0.4
+.008
-.004
+0.2
-0.1
)
+.008
-.004
+0.2
)
-0.1
t
.02±.004
(0.5±0.1)
.024±.004
(0.6±0.1)
Ceramic
Substrate
Derating Curve
100
80
60
40
20
0
-60 -40
-55
1E (90°C)
1J (95°C)
2A (100°C)
2B, 2E (110°C)
-20
0
80 100 120
85
Ambient Temperature
(°C)
20
40
60
140
160
155
-20
0
100 120
90 95 110
Terminal Part Temperature
(°C)
40
60
80
20
140
160
155
For resistors operated at an ambient temperature of 85°C or above, a
power rating shall be derated in accordance with the above derating curve.
ordering information
RN73H
Type
2B
Size
1E: 0.063W
1J: 0.1W
2A: 0.125W
2B: 0.25W
2E: 0.25W
T
Termination
Material
T: Sn
G: Au (1E,
1J only)
TD
For resistors operated terminal part temperature of described for each size
or above, a power rating shall be derated in accordance with derating curve.
Please refer to “Introduction of the derating curves based on the terminal
part temperature” in the beginning of our catalog before use.
1002
Nominal
Resistance
3 significant
figures +
1 multiplier
“R” indicates
decimal on
value <100Ω
B
Resistance
Tolerance
A: ±0.05%
B: ±0.1%
C: ±0.25%
D: ±0.5%
F: ±1.0%
25
T.C.R.
(ppm/°C)
05
10
25
50
100
Packaging
TP: 0402 only: 7" 2mm pitch
punched paper
TD: 0603, 0805, 1206, 1210:
7" 4mm pitch punched paper
TDD: 0603, 0805, 1206,
1210: 10" paper tape
TE: 0805, 1206, 1210:
7" embossed plastic
TED: 0805, 1206, 1210:
10" embossed plastic
For further information on packaging,
please refer to Appendix A
Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.
10/23/15
40
KOA Speer Electronics, Inc.
• 199 Bolivar Drive • Bradford, PA 16701 • USA • 814-362-5536 • Fax: 814-362-8883 • www.koaspeer.com
RN73H
high heat resistance, high reliability
metal film chip resistor
Rated
Power
Rated
T.C.R.
Part
Terminal
Rating Ambient
(ppm/°C)
Designation
Part
@ 85°C Temp.
Max.
(A±0.05%)
Temp.
±10
—
1/16W
85°C
90°C
±25
—
RN73H1E
(.063W)
—
±50
±5
100 - 59k
±10
47 - 59k
1/10W
RN73H1J
47 - 59k
±25
85°C
95°C
(.10W)
±50
—
±100
—
±5
100 - 100k
47 - 100k
±10
1/8W
RN73H2A
(.125W)
±25
85°C
100°C
47 - 100k
—
±50
—
±100
100 - 300k
±5
47 - 300k
±10
1/4W
RN73H2B
(.25W)
47 - 300k
±25
85°C
110°C
—
±50
—
±100
100 - 510k
±10
±25
51 - 510k
1/4W
RN73H2E
(.25W)
—
±50
85°C
110°C
±100
* No marking on E-192 values
—
resistors
applications and ratings
Resistance Range (Ω)
E-24, E-96, E-192*
(B±0.1%)
47 - 10k
47 - 300k
47 - 300k
100 - 59k
47 - 360k
15 - 1M
15 - 1M
—
100 - 100k
47 - 1M
15 - 1.5M
15 - 1.5M
—
100 - 300k
47 - 1M
15 - 1M
15 - 1M
—
100 - 510k
15 - 1M
15 - 1M
—
(C±0.25%)
47 - 10k
47 - 300k
47 - 300k
—
47 - 360k
15 - 1M
15 - 1M
—
—
47 - 1M
15 - 1.5M
15 - 1.5M
—
—
47 - 1M
15 - 1M
15 - 1M
—
100 - 510k
15 - 1M
15 - 1M
—
(D±0.5%)
47 - 10k
47 - 300k
10 - 300k
—
47 - 360k
10 - 1M
10 - 1M
10 - 1M
—
47 - 1M
10 - 1.5M
10 - 1.5M
10 - 1.5M
—
47 - 1M
10 - 1M
10 - 1M
10 - 1M
100 - 510k
10 - 1M
10 - 1M
10 - 1M
(F±1.0%)
47 - 10k
47 - 300k
10 - 300k
—
47 - 360k
10 - 1M
10 - 1M
10 - 1M
—
47 - 1M
10 - 1.5M
10 - 1.5M
10 - 1.5M
—
47 - 1M
10 - 1M
10 - 1M
10 - 1M
100 - 510k
10 - 1M
10 - 1M
10 - 1M
Maximum
Working
Voltage
50V
Maximum
Overload
Voltage
100V
75V
150V
150V
300V
200V
400V
200V
400V
Operating Temperature: -55°C to +155°C
environmental applications
Performance Characteristics
Parameter
Resistance
T.C.R.
Overload (Short time)
Resistance to Solder Heat
Rapid Change of Temperature
Moisture Resistance
Endurance at 85°C
High Temperature Exposure
Requirement
∆
R ±(%+0.05Ω)
Limit
Typical
Within specified tolerance
—
Within specified T.C.R.
—
±0.05%
±0.01%
±0.05%*
±0.01%
±0.1%*
±0.1%*
±0.1%*
±0.1%*
±0.02%
±0.05%
±0.03%
±0.05%
Test Method
25°C
+25°C/+125°C: T.C.R. +5 (x10
-6
K); +15°C/-55°C and +25°C/+155°C: other
Rated Voltage x 2.5 or Max. overload voltage, whichever is less for 5 seconds
260°C ± 5°C, 10 seconds ± 1 second
1E, 1J, 2A: -55°C (30 minutes), +155°C (30 minutes), 1000 cycles
2B, 2E: -55°C (30 minutes), +155°C (30 minutes), 500 cycles
85°C ± 2°C, 85%±5%RH, 1000 hours; 1.5 hr ON, 0.5 hr OFF cycle
85°C ± 2°C, 3000 hours, 1.5 hr ON, 0.5 hr OFF cycle
+155°C, 1000 hours
* Depends on resistance value, please contact KOA Speer for details.
Precautions for Use
• The properly and electrostatically measured taping materials are used for the components, but attention should be paid to the fact that there is some danger the parts
absorb on the top tapes to cause a failure in the mounting and the parts are destructed by static electricity (1J, 2A, 2B, 2E: 1kV and more, 1E: 0.5kV and more at Human
Body Model 100pF, 1.5kΩ) to change the resistance in the conditions of an excessive dryness or after the parts are given vibration for a long time as they are packaged
on the tapes. Similarly, care should be given not to apply the excessive static electricity when mounting on the boards.
• Ionic impurities such as flux etc. that are attached to these products or those mounted onto a PCB, negatively affect their moisture resistance, corrosion resistance, etc.
The flux may contain ionic substances like chlorine, acid, etc. while perspiration and saliva include ionic impurities like sodium (Na＋), chlorine (Cl−) etc. Therefore these
kinds of ionic substances may induce electrical corrosion when they invade into the products. Either thorough washing or using RMA solder and flux are necessary since
lead free solder contains ionic substances. Washing process is needed, before putting on moisture proof material in order to prevent electrical corrosion.
• Please pay attention that the top of an iron does not direct touch to the components. There is a risk that may cause a change in resistance. Take care that another risk
may happen that the protecting coat is carbonized in an instant when touched directly by the top of the iron, also climatic-proof for electric corrosion or insulation of
protecting coat may be dropped down. Be sure not to give high temperature on the top of the iron as it will degrade the protecting coat.
• Avoid storing components under direct sun rays, high temperature/humidity. Direct sun rays will cause quality change of taping and difficulty of keeping appropriate peeling
strength. 5~35°C/35~75%RH, there is no deterioration of solderability for 12 months, but take special care for storing, because condensation, dust, and toxic gas like
hydrogen sulfide, sulfurous acid gas, hydrogen chloride, etc. may drop solderability.
●
The upper electrodes could be peeled off when a heat-resistant masking tape is attached to the mounted chip resistors and then detached from them. It is confirmed that
the adhesiveness gets stronger due to the exposure to heat under mounting. Accordingly, we recommend the use of masking tape be refrained. If the use of heat-resistant
masking tape is unavoidable, please make sure that the adhesives on the tape do not directly come in contact with the product.
For Surface Temperature Rise Graph see Environmental Applications. Additional environmental applications can also be found at www.koaspeer.com
Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.
11/06/17
KOA Speer Electronics, Inc.
• 199 Bolivar Drive • Bradford, PA 16701 • USA • 814-362-5536 • Fax: 814-362-8883 • www.koaspeer.com
41
Medical Electronics
京公网安备 11010802033920号
EEWORLD
