CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typ values are for information purposes only. Unless otherwise noted, all tests are
at the specified temperature and are pulsed tests, therefore: T
J
= T
C
= T
A
Electrical Specifications
PARAMETER
V
IN
= 3.3V, V
BOOST
= 12V,
R
OSC
= 100k,
T
A
= 25°C Unless Otherwise Specified.
CONDITIONS
MIN
TYP
MAX
UNIT
DESCRIPTION
DC/DC BOOST CONVERTER
IQ1_B
IQ2_B
V(FBB)
V
REF
V
ROSC
I(FBB)
V
DDB
D
MAX
I(LX)
MAX
R
DS-ON
I
LEAK-SWITCH
V
BOOST
V
BOOST
/V
IN
V
BOOST
/I
O1
F
OSC-RANGE
F
OSC1
Quiescent Current - Shut-down
Quiescent Current - Switching
Feedback Voltage
Reference Voltage
Oscillator Set Voltage
Feedback Input Bias Current
Boost Converter Supply Range
Maximum Duty Cycle
Peak Internal FET Current
Switch On Resistance
Switch Leakage Current
Output Range
Line Regulation
Load Regulation
Frequency Range
Switching Frequency
at V
BOOST
= 10V, I(LX) total = 500mA
I(LX) total
V
BOOST
> V
IN
+ V
DIODE
2.7V < V
IN
< 13.2V, V
BOOST
= 15V
50mA < I
O1
< 300mA
R
OSC
range = 240k to 60k
R
OSC
= 100k
200
620
680
5
0.1
0.5
1000
750
2.7
85
92
2.75
0.15
2
17
ENBN = ENP = 0V
ENBN = V
DDB
1.275
1.260
1.260
0.8
4.8
1.300
1.310
1.325
0.1
17
10
8
1.325
1.360
1.390
µA
mA
V
V
V
µA
V
%
A
µA
V
%
%
kHz
kHz
POSITIVE REGULATED CHARGE PUMP (V
ON
)
Most positive V
ON
output depends on the magnitude of the V
DDP
input voltage (normally connected to V
BOOST
) and the external component
configuration (doubler or tripler)
V
DDP
IQ1(V
DDP
)
IQ2(V
DDP
)
V(FBP)
I(FBP)
I(DRVP)
Supply Input for Positive Charge Pump
Quiescent Current - Shut-down
Quiescent Current - Switching
Feedback Reference Voltage
Feedback Input Bias Current
RMS DRVP Output Current
V
DDP
= 12V
V
DDP
= 6V
ILR_V
ON
F
PUMP
Load Regulation
Charge Pump Frequency
5mA < I
L
< 15mA
Frequency set by R
OSC
- see boost section
15
-0.5
0.03
0.5*F
OSC
0.5
Usually connected to V
BOOST
output
ENP = 0V
ENBN = ENP = V
DDB
1.245
5
11.5
2.3
1.310
0.1
60
17
20
5
1.375
V
µA
mA
V
µA
mA
mA
%/mA
FN7100 Rev 5.00
March 9, 2006
Page 2 of 17
EL7581
Electrical Specifications
PARAMETER
V
IN
= 3.3V, V
BOOST
= 12V,
R
OSC
= 100k,
T
A
= 25°C Unless Otherwise Specified.
(Continued)
CONDITIONS
MIN
TYP
MAX
UNIT
DESCRIPTION
NEGATIVE REGULATED CHARGE PUMP (V
OFF
)
Most negative V
OFF
output depends on the magnitude of the V
DDN
input voltage (normally connected to V
BOOST
) and the external component
configuration (doubler or tripler)
V
DDN
IQ1(V
DDN
)
IQ2(V
DDN
)
V(FBN)
I(FBN)
I(DRVN)
Supply Input for Negative Charge Pump
Quiescent Current - Shut-down
Quiescent Current - Switching
Feedback Reference Voltage
Feedback Input Bias Current
RMS DRVN Output Current
Magnitude of input bias
V
DDN
= 12V
V
DDN
= 6V
ILR_V
OFF
F
PUMP
Load Regulation
Charge Pump Frequency
-15mA < I
L
< -5mA
Frequency set by R
OSC
- see boost section
15
-0.5
0.03
0.5*F
OSC
0.5
Usually connected to V
BOOST
output
ENBN = 0V
ENBN = V
DDB
-80
5
1.2
2.3
0
0.1
60
17
10
5
+80
V
µA
mA
mV
µA
mA
mA
%/mA
ENABLE CONTROL LOGIC
V
HI-ENX
V
LO-ENX
IL(EN”X”)
IL(ENBN)
IL(ENP)
Enable Input High Threshold
Enable Input Low Threshold
Logic Low Bias Current
Logic High Bias Current
Logic High Bias Current
X = “BN”, “P”
X = “BN”, “P”
X = “BN”, “P” = 0V
ENBN = 5V
ENP = 5V
0.1
7.5
3.3
15
7.5
1.4
0.6
V
V
µA
µA
µA
OVER-TEMPERATURE PROTECTION
T
OT
T
HYS
Over-temperature Threshold
Over-temperature Hysteresis
130
40
°C
°C
FN7100 Rev 5.00
March 9, 2006
Page 3 of 17
EL7581
Pin Descriptions
I = Input, O = Output, S = Supply
PIN NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
PIN NAME
VSSB
SS
FBB
VDDB
LX
LX
LX
DRVN
VDDN
FBN
VSSP
FBP
VDDP
DRVP
PGND
PGND
VREF
ENBN
ENP
ROSC
PIN TYPE
S
I
I
S
O
O
O
O
S
I
S
I
S
O
O
O
I
I
I
I
PIN FUNCTION
Ground for DC/DC boost and reference circuits; chip substrate
Soft-start input; the capacitor connected to this pin sets the current limited start time
Voltage feedback input for boost circuit; determines boost output voltage, V
BOOST
Positive supply input for DC/DC boost circuits
Boost regulator inductor drive connected to drain of internal NFET
Boost regulator inductor drive connected to drain of internal NFET
Boost regulator inductor drive connected to drain of internal NFET
Driver output for the external generation of negative charge pump voltage, V
OFF
Positive supply for input for V
OFF
generator
Voltage feedback input to determine negative charge pump output, V
OFF
Negative supply pin for both the positive and negative charge pumps
Voltage feedback to determine positive charge pump output, V
ON
Positive supply input for V
ON
generator
Voltage driver output for the external generation of positive charge pump, V
ON
Power ground, connected to source of internal NFET
Power ground, connected to source of internal NFET
Voltage reference for charge pump circuits; decouple to ground
Enable pin for boost (V
BOOST
generation) and negative charge pump (V
OFF
generation);
active high
Enable for DRVP (V
ON
generation); active high
Connected to an external resistor to ground; sets the switching frequency of the DC/DC boost
As we all know, the operating system has to create a stack area and has its own tasks, but I saw a routine today as follows:#include rtthread.h
#include rtdevice.h
#include board.h
#include drv_lcd.h
...
【Chuanglong TL570x-EVM】Review 0 6 - QT Dome Test1. QT project compilation instructions2. QT software installation
For QT software installation and environment configuration, please refer to the PDF fi...
The CH583 and CH582 chips provide I2C interface with the following features: l Supports master mode and slave mode, supports multiple masters and multiple slaves. l Supports two speed modes: 100KHz an...
The Kaluga board has its own official case library. This article records the usage of the library.
1. Obtaining the case library
The "esp-dev-kits" repository on the Espressif official site on GitHub ...
Samsung may see more growth in the coming months, possibly at the expense of rivals like Xiaomi, according to data from 91mobiles' 2020 Buyer Insights Survey. Image source: 91mobiles According to d...[Details]
According to CINNO Research industry information, isMedia, a camera module inspection equipment company, has signed a camera module inspection equipment supply contract with Japan's Sharp (acquired b...[Details]
Over the past decade, the survival of Moore's Law has been the focus of heated debate. Although industry giants like Intel and TSMC continue to make breakthroughs in smaller process nodes, it is an i...[Details]
The figure shows a schematic diagram of an electronic motor starter circuit. This motor starter protects single-phase motors from voltage fluctuations and overloads. Its outstanding feature is the ...[Details]
Design
an
FPGA
-based IP-BX telephone application system for the
interface
connection
between the traditional telephone network (PSTN) and the PC
. The USB2.0
interface
device ...[Details]
Application of Acoustic Emission Technology in Water Pressure Test of Spherical Tanks
In order to store and peak the gas supplied, gas companies must establish storage and distribution stations. At...[Details]
The DG4000 series is a multifunctional signal generator that integrates function generators, arbitrary waveform generators, pulse generators, harmonic generators, analog/digital modulators, frequency...[Details]
Advanced clock control timer TIM1 & TIM8 introduction: The advanced control timer of STM32F4 contains an automatic reload counter, the input of the counter is a pre-divided system clock. This timer h...[Details]
1 Introduction
Inductive key technology is an emerging technology that has been widely used in various products. Especially in the past two years, home appliances using inductive keys have bee...[Details]
An in-cabin monitoring system shows how it detects where a driver is looking, as indicated by the yellow line. If the driver looks too long at non-“safe areas” such as the side mirrors, rearview mi...[Details]
When the system is started in Nand mode, the hardware copies the first 8KB of Nand Flash to Steppingstone, and then runs the program from address 0. In the code within 8KB, we need to complete the nec...[Details]
Automobile production has been hit by chip shortages. Research firm IHS Markit has significantly lowered its forecast for small car production from 2021 to 2023, lowering its forecast for small car p...[Details]
In simple buildings without access to 220 V mains electricity, an emitter-follower-based sound-and-light-controlled switch is used to control the operation of LED lighting. The method is simple, ea...[Details]
Since the beginning of this year, Neijiang City has emphasized the priority of industry and manufacturing, adhered to the guidance of new industrialization, implemented the industrial doubling plan in...[Details]
stm32/stm8
京公网安备 11010802033920号
EEWORLD
