HANBit
HFDOM40C-xxxSx
40Pin Flash Disk Module Min.8MB ~ Max.512MB, True IDE Interface
Mode, 3.3V / 5.0V Operating
Part No. HFDOM40C-xxxSx
1. PRODUCT OVERVIEW
GENERAL DESCRIPTION
The HFDOM40C-xxxSx series 40Pin Flash Disk Module is a flash technology based with True IDE interface flash
memory card. It is constructed with flash disk controller chip and NAND -type (Samsung) flash memory device. The
HFDOM40C-xxxSx series operates in both 3.3 -Volt and 5.0-Volt power supplies. It comes in capacity of 8, 16, 32, 64, 128,
192, 256 MB and up to 512 MB formatted 40Pin type .
By optimizing flash memory management, the life of this HFDOM40C-xxxSx series can be extended to its maximum
level. Because the ECC function is included, the correctness of data transfer between the HFDOM40C-xxxSx series and
a True IDE compatible interface device can be guaranteed.
The HFDOM40C-xxxSx series is fully compatible with applications such as CPU card / board, set top box, industry /
military PC / Notebook, security equipment, measuring instrument and embedded systems.
FEATURES
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
True IDE compatible host interface
Direct plug in for 3.5″ IDE Connectors
40 pin 2.54mm IDE Connector
Very high performance, very low power consumption
Automatic error correction
Support 3 power save mode : stop/idle/active
Support for CIS implemented with 256 bytes of attribute memory
3.3V/5.0V operation voltage
Host data transfer rate : 20MB/s
Flash data transfer rate : 10MB/s
Host Interface bus width : 8/16 bit Access
Flash Interface bus width : 8 bit Access
Capacity : Min. 8MB ~ Max. 512MB
MTBF : 1,000,000 hours, minimum 30,000 insertions
Operating vibration : 15G peak to peak maximum
Operating shock : 1,000G maximum
PRODUCT SPECIFICATIONS
Capacities :
8, 16, 32, 64, 128, 192, 256, 384 and up to 512 MB (formatted)
Operating Voltage :
Operating mode
Stop mode
3.3V / 5.0V
±
10%
Power consumptions :
40 mA (typ), 70 mA (Max)
30 uA (Max)
0° C to + 70° C
- 10° C to + 85° C
95%(Max)
Environment conditions :
Operating temperature
Storage temperature
Relative humidity
Mechanical conditions :
Weight : Maximum 9.0g
URL : www.hbe.co.kr
REV 1.0 (March.2003)
1 / 10
HANBit Electronics Co., Ltd
.
HANBit
ELECTRICAL SPECIFICATIONS
Table 1.1 Absolute Maximum Ratings
Symbol
V
DD
V
IN
I
IN
T
STG
Parameter
Supply voltage
Input voltage
DC input current
Storage temperature
Ratings
- 0.3 to + 7.0
- 0.3 to + 7.0
- 10
- 10 to + 85
HFDOM40C-xxxSx
Unit
V
V
mA
°
C
Table 1.2 Recommended Operating Conditions
Symbol
V
DD
T
a
Parameter
DC Supply voltage
Storage temperature
5V
3.3V
Ratings
4.75 to 5.25
3.0 to 3.6
- 0 to +70
Unit
V
V
°
C
Table 1.3 DC Characteristics
(Ta=0° C to 70° C, V
DD
=3.0 to 5.0V)
Symbol
I
DD
I
ds
V
DD
V
DD
Parameter
Operating Current
Stop Current
High Level Output Voltage
Low Level Output Voltage
2.4
0.4
Min.
Typ.
30
Max.
70
100
Unit
mA
µA
V
V
CAPACITY SPECIFICATIONS
Table 1.4 Capacity Specifications
Part Number
HFDOM40C-008Sx
HFDOM40C-016Sx
HFDOM40C-032Sx
HFDOM40C-064Sx
HFDOM40C-128Sx
HFDOM40C-192Sx
HFDOM40C-256Sx
HFDOM40C-384Sx
HFDOM40C-512Sx
Capacity
(Unformatted)
7,864,320
bytes
15,990,784
bytes
32,243,712
bytes
65,536,000
bytes
131,858,432
bytes
196,608,000
bytes
265,027,584
bytes
395,837,440
bytes
531,890,176
bytes
Total Sector
15,360
31,232
62,976
128,000
257,536
384,000
517,632
773,120
1,038,848
Cylinders
30
61
123
250
503
750
1011
1510
2029
Heads
16
16
16
16
16
16
16
16
16
Sectors
32
32
32
32
32
32
32
32
32
URL : www.hbe.co.kr
REV 1.0 (March.2003)
2 / 10
HANBit Electronics Co., Ltd
.
HANBit
PHYSYCAL SPECIFICATIONS
55.50± 0.1mm
HFDOM40C-xxxSx
< View from front side >
Jumper
Master
1,2
Close
40
3
2
1
30.50± 0.2mm
Slave
2,3
Close
2
39
1
8.90mm± 0.1mm
7.50mm
1.4mm± 0.1mm
Figure 1.1 40 pin Type Flash Disk Module Dimensions
TOP Side
3
2
1
Bottom Side
40
39
2
1
1
2
39
40
TOP Side
TOP Side
Bottom Side
Bottom Side
Top-Connector
Attach
Bottom-Connector
Attach
URL : www.hbe.co.kr
REV 1.0 (March.2003)
3 / 10
HANBit Electronics Co., Ltd
.
HANBit
HFDOM40C-xxxSx
INSTALLTION GUIDE
1) Setting Method
①
②
Make sure your computer is turned off before you open the case.
Plug the carefully into the 40pin IDE slot on your computer.
Caution:
Make sure to align pin1 on host adapter interface connector with pin 1 on your Flash Disk Module. Pin 1
is indicated by a triangle on the Flash Disk Module connector.
The Flash Disk Module is used power connector cable of the computer.
Caution:
If you need to remove your Flash Disk Module, use both hands to pull it out carefully.
Check all cable connections and then replace your computer cover.
Before you format or partition your new drive, you must configure your computer's BIOS so that the computer can
recognize your new drive.
①
Turn your computer on. As your computer start up, watch the screen for a message describing how to run the
system setup program on the screen (sometimes called BIOS or CMOS setup). This is usually done by pressing a
special key, such as
Delete, Esc
or
F1
during startup. See your computer manual for details. Press the
appropriate key to run the system setup program.
If your BIOS provides automatic drive detection (an "AUTO" drive type), select this option.
(
We recommend
to use Normal / CHS mode to partition your Flash Disk Module to get the maximum formatted capacity.
)
This allows your computer to configure itself automatically for your new drive.
If your BIOS dose not provide
“
AUTO” drive detection, select "User-defined" drive setting and enter the
CHS values from the table.
BIOS Settings (see specification) Capacity Cylinders Heads Sectors(unformatted)
③
Save the settings and exit the System Setup program. ( your computer will automatica lly reboot ) After you
configure your computer, you can use the standard DOS commands to partition and format your Flash Disk
Module, as described below.
③
④
2) BIOS setting Method
②
3)
Formatting Method
To partition your new Flash Disk Module with Microsoft DOS program :
Insert a bootable DOS diskette into your diskette drive and restart your computer.
①
Insert a DOS program diskette that contains the
FDISK.EXE
and
FORMAT.COM
②
programs into your diskette drive. Use the same DOS version that is on your bootable diskette. At the
A:\ >
prompt, type
“
FDISK”
and press
Enter.
③
④
Select
“
Create DOS partition or logical DOS drive
”
by pressing
1.
Then press
Enter.
Select
“
Create primary DOS partition”
by pressing
1
again. Then press
Enter.
Create your first drive partition. If you are creating a part ition that will be used to boot your computer (drive C),
make sure that the partition is marked active.
Create an extended partition and additional logical drives as necessary, until all the space on your new hard drive
has been partitioned.
When the partitioning is complete,
FDISK
reboots your computer.
Caution:
Make sure to use the correct drive letters so that you do not format a drive that already contains data.
At the
A:\ >
prompt, type
“
format c:/s”
, where
c
is the letter of your first new partition, Repeat the format process
for all the new partitions you have created.
After you format your drive, it is ready to use.
⑤
⑥
⑦
⑧
URL : www.hbe.co.kr
REV 1.0 (March.2003)
4 / 10
HANBit Electronics Co., Ltd
.
HANBit
HFDOM40C-xxxSx
2. PIN INFORMATION
PIN ASSIGNMENTS AND PIN TYPE
Table 2.1 Pin Assignment and Pin type
Pin
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
Signal
/RESET
D07
D06
D05
D04
D03
D02
D01
D00
GND
Reserved
/IOW
/IOR
IORDY
Reserved
IRQ
A01
A00
/CS0
/DASP(LED)
Pin Type
I
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
DC
--
I
I
O
--
O
I
I
I
I/O
Pin
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
Signal
GND
D08
D09
D10
D11
D12
D13
D14
D15
Key Pin
GND
GND
GND
Reserved
GND
/IOIS16
/PDIAG
A02
/CS1
GND
Pin Type
Ground
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
--
Ground
Ground
Ground
--
Ground
O
I/O
I
I
Ground
URL : www.hbe.co.kr
REV 1.0 (March.2003)
5 / 10
HANBit Electronics Co., Ltd
.
京公网安备 11010802033920号
EEWORLD
