drivers designed for clock distribution in new, high-
performance ECL systems. They accept one differential or
single-ended input, with V
BB
used for single-ended
operation. The signal is fanned out to nine identical
differential outputs. An enable input is also provided such
that a logic HIGH disables the device by forcing all Q
outputs LOW and all /Q outputs HIGH.
The device is specifically designed and produced for low
skew. The interconnect scheme and metal layout are
carefully optimized for minimal gate-to-gate skew within
the device. Wafer characterization and process control
ensure consistent distribution of propagation delay from lot
to lot. Since the E111 shares a common set of “basic”
processing with the other members of the ECLinPS™
family, wafer characterization at the point of device
personalization allows for tighter control of parameters,
including propagation delay.
To ensure that the skew specification is met, it is
necessary that both sides of the differential output are
terminated into 50Ω, even if only one side is being used. ln
most applications, all nine differential pairs will be used
and, therefore, terminated. In the case where fewer than
nine pairs are used, it is necessary to terminate at least the
output pairs on the same package side (i.e. sharing the
same V
CCO
as the pair(s) being used on that side) in order
to maintain minimum skew.
The V
BB
output is intended for use as a reference
voltage for single-ended reception of ECL signals to that
device only. When using V
BB
for this purpose, it is
recommended that V
BB
is decoupled to V
CC
via a 0.01µF
capacitor.
s
V
BB
output
s
Enable input
s
Fully compatible with industry standard 10KH, 100K
I/O levels
s
75K
Ω
input pulldown resistors
s
Fully compatible with ON Semiconductor
MC10E/100E111
s
Available in 28-pin PLCC package
BLOCK DIAGRAM
Q
0
Q
0
Q
1
Q
1
Q
2
Q
2
Q
3
Q
3
IN
IN
EN
Q
5
Q
6
Q
4
Q
4
Q
5
PIN NAMES
Pin
Function
Differential Input Pair
Enable Input
Differential Outputs
V
BB
Output
V
CC
to Output
Q
6
Q
7
Q
7
Q
8
V
BB
Q
8
IN, /IN
/EN
Q0, /Q0 — Q8, /Q8
V
BB
V
CCO
M9999-032006
hbwhelp@micrel.com or (408) 955-1690
Rev.: E
Amendment: /0
1
Issue Date: March 2006
Micrel, Inc.
SY10E111
SY100E111
PACKAGE/ORDERING INFORMATION
/Q
0
Q
1
V
CCO
Ordering Information
(1)
/Q
1
/Q
2
Q
2
Q
0
Part Number
25 24 23 22 21 20 19
Package
Type
J28-1
J28-1
J28-1
J28-1
J28-1
J28-1
J28-1
J28-1
J28-1
J28-1
J28-1
J28-1
Operating
Range
Industrial
Industrial
Industrial
Industrial
Commercial
Commercial
Commercial
Commercial
Industrial
Industrial
Industrial
Industrial
Package
Marking
SY10E111JI
SY10E111JI
SY100E111JI
SY100E111JI
SY10E111JC
SY10E111JC
SY100E111JC
SY100E111JC
SY10E111JY with
Pb-Free bar-line indicator
SY10E111JY with
Pb-Free bar-line indicator
SY100E111JY with
Pb-Free bar-line indicator
SY100E111JY with
Pb-Free bar-line indicator
Lead
Finish
Sn-Pb
Sn-Pb
Sn-Pb
Sn-Pb
Sn-Pb
Sn-Pb
Sn-Pb
Sn-Pb
Matte-Sn
Matte-Sn
Matte-Sn
Matte-Sn
V
EE
/EN
IN
V
CC
/IN
V
BB
NC
26
27
28
1
2
3
4
5
6
7
8
9
10 11
18
17
Q
3
/Q
3
Q
4
V
CCO
/Q
4
Q
5
/Q
5
SY10E111JI
SY10E111JITR
(2)
SY100E111JI
SY100E111JITR
(2)
SY10E111JC
SY10E111JCTR
(2)
SY100E111JC
SY100E111JCTR
(2)
SY10E111JY
(3)
PLCC
TOP VIEW
J28-1
16
15
14
13
12
/Q
8
Q
8
/Q
7
Q
7
28-Pin PLCC (J28-1)
SY10E111JYTR
(2, 3)
SY100E111JY
(3)
SY100E111JYTR
(2, 3)
Notes:
V
CCO
/Q
6
Q
6
1. Contact factory for die availability. Dice are guaranteed at T
A
= 25°C, DC Electricals only.
2. Tape and Reel.
3. Pb-Free package is recommended for new designs.
TIMING DIAGRAMS
IN
/IN
t
s
/EN
50%
/EN
/Q
Q
75 mV
Figure 1. Set-up Time
Figure 2. Hold Time
IN
/IN
t
H
50%
75 mV
/Q
Q
75 mV
75 mV
IN
/IN
t
r
/EN
50%
/Q
Q
Figure 3. Release Time
M9999-032006
hbwhelp@micrel.com or (408) 955-1690
2
Micrel, Inc.
SY10E111
SY100E111
DC ELECTRICAL CHARACTERISTICS
V
EE
= V
EE
(Min.) to V
EE
(Max.); V
CC
= V
CCO
= GND
T
A
= –40
°
C
Symbol
V
BB
Parameter
Output Reference
Voltage
10E
100E
Input HIGH Current
Power Supply
Current
10E
100E
Min.
Typ.
Max.
Min.
–1.38
–1.38
—
—
—
T
A
= 0
°
C
Typ.
—
—
—
48
48
Max.
T
A
= +25
°
C
Min.
Typ.
—
—
—
48
48
Max.
T
A
= +85
°
C
Min.
Typ.
—
—
—
48
55
Max.
–1.19
–1.26
150
60
69
µA
mA
60
60
—
—
60
60
—
—
Unit
V
–1.27 –1.35
–1.26 –1.38
150
—
–1.25 –1.31
–1.26 –1.38
150
—
I
IH
I
EE
AC ELECTRICAL CHARACTERISTICS
V
EE
= V
EE
(Min.) to V
EE
(Max.); V
CC
= V
CCO
= GND
T
A
= –40
°
C
Symbol
t
PD
Parameter
Propagation Delay to
Output
IN (differential)
(1)
IN (single-ended)
(2)
Enable
(3)
Disable
(3)
Within-Device Skew
(4)
Set-up Time
/EN to IN
(5)
Hold Time
IN to /EN
(6)
Release Time
/EN to IN
(7)
Minimum Input Swing
(8)
Common Mode Range
(9)
Rise/Fall Times
(20% to 80%)
Min.
Typ.
Max.
Min.
T
A
= 0
°
C
Typ.
Max.
T
A
= +25
°
C
Min.
Typ.
Max.
T
A
= +85
°
C
Min.
Typ.
Max.
Unit
ps
430
330
450
450
—
200
0
300
250
–1.6
275
—
—
—
—
25
0
–200
100
—
—
375
630
730
850
850
50
—
—
—
—
–0.4
600
430
330
450
450
—
200
0
300
250
–1.6
275
—
—
—
—
25
0
–200
100
—
—
375
630
730
850
850
50
—
—
—
—
–0.4
600
430
330
450
450
—
200
0
300
250
–1.6
275
—
—
—
—
25
0
–200
100
—
—
375
630
730
850
850
50
—
—
—
—
–0.4
600
ps
ps
ps
ps
mV
V
ps
t
SKEW
t
S
t
H
t
R
V
PP
V
CMR
t
r
t
f
Notes:
1. The differential propagation delay is defined as the delay from the crossing points of the differential input signals to the crossing point of the differential
output signals.
2. The single-ended propagation delay is defined as the delay from the 50% point of the input signal to the 50% point of the output signal.
3. Enable is defined as the propagation delay from the 50% point of a
negative
transition on /EN to the 50% point of a
positive
transition on Q (or a negative
transition on /Q). Disable is defined as the propagation delay from the 50% point of a
positive
transition on /EN to the 50% point of a
negative
transition
on Q (or a positive transition on /Q).
4. The within-device skew is defined as the worst case difference between any two similar delay paths within a single device.
5. The set-up time is the minimum time that /EN must be asserted prior to the next transition of /IN/IN to prevent an output response greater than
±75mV
to that /IN/IN transition (see Figure 1).
6. The hold time is the minimum time that /EN must remain asserted after a negative going IN or a positive going /IN to prevent an output response greater
than
±75mV
to that IN, /IN transition (see Figure 2).
7. The release time is the minimum time that /EN must be de-asserted prior to the next IN, /IN transition to ensure an output response that meets the specified
IN to Q propagation delay and output transition times (see Figure 3).
8. V
PP
(min.) is defined as the minimum input differential voltage which will cause no increase in the propagation delay. The V
PP
(min.) is AC limited for the
E111, as a differential input as low as 50mV will still produce full ECL levels at the output.
9. V
CMR
is defined as the range within which the V
IH
level may vary, with the device still meeting the propagation delay specification. The V
IL
level must be
such that the peak-to-peak voltage is less than 1.0V and greater than or equal to V
PP
(min.).
M9999-032006
hbwhelp@micrel.com or (408) 955-1690
3
Micrel, Inc.
SY10E111
SY100E111
28-PIN PLCC (J28-1)
Rev. 03
MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131
TEL
USA
+ 1 (408) 944-0800
FAX
+ 1 (408) 474-1000
WEB
http://www.micrel.com
The information furnished by Micrel in this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use.
Micrel reserves the right to change circuitry and specifications at any time without notification to the customer.
Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can
reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into
the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser’s
use or sale of Micrel Products for use in life support appliances, devices or systems is at Purchaser’s own risk and Purchaser agrees to fully indemnify
Micrel for any damages resulting from such use or sale.
I started playing with digital electronics and felt that the power supply was not easy to use. I found LM317 and made a power supply module. It is simple and easy to make. If you are interested, you c...
[i=s]This post was last edited by cruelfox on 2020-4-30 00:46[/i] I have been playing with the Cortex-A7 core of the STM32MP157A because it is new to me. In addition to the two A7 cores, this chip is...
About HYT
HYC Technology (HYC for short) was founded in Shenzhen, China in 2000 and moved to Qingyuan, Guangdong in 2014. It is now headquartered in Qingyuan and has branches in Shenzhen and Wuhan. HY...
From refrigerators, washing machines, and dishwashers commonly used in homes to pumps and fans in factories and processing plants, and air conditioning systems in offices, small and medium-sized motor...
Based on Xunwei iTOP-4418 Development Department, in Eclipse, click the "Windows" menu and select "Android Virtual Device Manager" to start
Simulator Management Plugin. Then click “Create…” as shown b...
I received a development board from EEWORLD today. The board was packed very tightly and the courier was also very good. I went to the Cainiao Station to pick it up after get off work in the evening. ...
Under the background of my country's rapid economic development, the market demand for central air conditioners has shown a strong growth trend due to the rapid development of real estate. Attrac...[Details]
The navigation products currently sold on the market are divided into handheld devices, car GPS, GP mobile phones, and GPS modules. Regardless of the type of navigation product, the power supply is...[Details]
At present, the most commonly used LED dimming power supplies are: LED thyristor dimming power supplies, LED 0/1-10V dimming power supplies, and PWM dimming power supplies. Other dimming working pr...[Details]
On March 8, the day before the opening of Shanghai AWE, Haier released a smart home consisting of a complete set of fully interconnected smart home appliances, involving 161 smart life scenarios in ...[Details]
Digital capacitive isolators are often used in environments that include large electric motors, generators, and other devices that generate strong electromagnetic fields. Exposure to these magnetic...[Details]
In the ever-changing manufacturing environment, flexible and efficient material handling is essential. Currently, autonomous mobile
robots
(AMRs) are reshaping logistics operations and beco...[Details]
Abstract: The coding and decoding circuits in the hardware system of the dual-network digital fax machine are designed, and the FPGA chip is used for system implementation and verification. The c...[Details]
Benefiting from the upgrading of market consumption and people's higher requirements for driving experience, smooth smart cockpit experience has gradually become the mainstream demand of the automoti...[Details]
Use the parallel port P1 of AT89S51 to connect a 4×4 matrix keyboard, with P3.0-P3.3 as input lines and P3.4-P3.7 as output lines; the digital keys "0-9" are displayed on the digital tube, and the ot...[Details]
According to previous news, this year's iPhone 14 series will adopt two screen designs. The Pro version will adopt a no-notch solution and be equipped with a perforated screen, while the standard ver...[Details]
This time we are going to make a USB card reader for an SD card. We modified the USB flash drive project simulated by NAND Flash last time, so we only need to modify a small part. Most of the project...[Details]
Many consumers pay little attention to the installation of LED screens after purchasing them, leaving everything to the installer. However, many LED screen manufacturers only check the connection p...[Details]
With the rapid development of science and technology, high-tech has been widely used in various industries. High-tech magnetostrictive level gauges are used to measure the liquid level of various s...[Details]
In the official M1 Ultra announcement, Apple introduced how Mac Studio, with the support of a new custom chip, enables 2.5 TB/s interconnection bandwidth between UltraFusion chips and allows two M1 M...[Details]
Mitsubishi PLC FX3U is a powerful small controller widely used in industrial automation. Its master control instructions are the core of program control. For programmers, it is very important to ma...[Details]
Analogue and Mixed Signal
京公网安备 11010802033920号
EEWORLD
