Testing conditions: 5E4 (50,000 operations) T55 (0 to 55°C)
Ratings
Model
Rated voltage
125 VAC
30 VDC
Item
3A
3A
SS-3P /
SS-3FP models
SS-01P models
Resistive load
0.1 A
0.1 A
Note 1. The above rating values apply under the following test conditions.
(1) Ambient temperature: 20±2°C
(2) Ambient humidity: 65±5%
(3) Operating frequency: 20 operations/min
Note 2. Consult your OMRON sales representative for information on models
for other loads.
Characteristics
Item
Permissible operating speed
Permissible
operating
frequency
Mechanical
Electrical
50 mΩ max.
Model
SS-3P models
SS-01P models
0.1 mm to 1 m/s (for pin plunger models)
300 operations/min
30 operations/min
100 MΩ min. (at 500 VDC with insulation tester)
100 mΩ max.
1,000 VAC 50/60 Hz for 1 min
1,500 VAC 50/60 Hz for 1 min
1,500 VAC 50/60 Hz for 1 min
10 to 55 Hz, 1.5 mm double amplitude
1,000 m/s
2
{approx. 100G} max.
300 m/s
2
{approx. 30G} max.
1,000,000 operations min. (60 operations/min)
70,000 operations min.
(20 operations/min, 125 VAC)
100,000 operations min.
(20 operations/min, 30 VDC)
100,000 operations min.
(60 operations/min)
100,000 operations min.
(20 operations/min, 30 VDC)
50 mΩ max.
SS-3FP models
Insulation resistance
Contact resistance (initial value)
Between terminals of the
same polarity
Dielectric
strength *1
Between current-carrying
metal parts and ground
Between each terminals
and non-current-carrying
metal parts
Vibration
Malfunction
resistance *2
Shock
resistance
Durability
Malfunction *2
Mechanical
Durability *3
Electrical
200,000 operations min.
(20 operations/min)
IEC IP40
Class I
250
Degree of protection
Degree of protection against electric
shock
Proof tracking index (PTI)
Ambient operating temperature
Ambient operating humidity
Weight
-25°C to
+85°C
(at ambient humidity of 60% max.) (with no icing or condensation)
85% max. (for
+5
to
+35°C)
Approx. 1.6 g (pin plunger models)
Note. The data given above are initial values.
*1. The values for dielectric strength shown are for models with a Separator (refer to
"Micro Switch Common Accessories").
*2. The values are at Free Position and Total Travel Position values for pin plunger, and Total Travel Position value for lever.
Close or open circuit of the contact is 1 ms max.
*3. For testing conditions, consult your OMRON sales representative.
2
SS-P
Terminals/Appearances
(Unit: mm)
●Solder
terminals
●Quick
Connect Terminals (#110)
Subminiature Basic Switch
●PCB
terminals
(5.25)
1.8
7.3
3.3
±0.1
3.2
2.15
8.55
15.5
3-1.6 dia. holes
0.5
6.4
±0.2
7.6
±0.2
7.6
±0.2
11
7.1
3.3
±0.1
1.85
3-2.8
0.5
6.4
±0.2
16.1
±0.2
8.8
±0.2
3-1.2
3-0.8
1.3
0.5
6.4
±0.2
3.9
3.3
±0.1
<PCB Mounting Dimensions (Reference)>
16.1
±0.1
8.8
±0.1
3-1.35~1.5 dia.
S
S
P
-
Mounting Holes
(Unit: mm)
2-2.4 dia. mounting holes
or M2.3 screw holes
9.5
±0.1
Dimensions
(Unit: mm)
and Operating Characteristics
The illustrations and dimensions are for models with solder terminals. Refer to
"Terminals/Appearances"
for details on models with quick connect terminals (#110) or
PCB terminals.
●Pin
plunger
SS-3GP
SS-01GP
7.55
±0.2
PT
3.5
2.5
±0.07
dia
.
2
A
2.35
+0.075
-
0.05
6.9
dia
7.7
3.3
±0.1
Operating characteristics
Operating Force
Releasing Force
Pretravel
Overtravel
Movement Differential
Operating Position
OF
RF
PT
OT
MD
OP
Model
Max.
Min.
Max.
Min.
Max.
SS-3GP
SS-01GP
+0.075
OP 2.35
-0.05
1.50 N {153 gf}
0.2 N {20 gf}
0.6 mm
0.4 mm
0.15 mm
8.4±0.3 mm
7.3
2.15
8.55
15.5
5.15 9.5
±0.1
19.8
±0.2
3-1.6 dia. holes
0.5
6.4
±0.2
●Hinge
lever
SS-3GLP
SS-01GLP
t=0.3 Stainless-steel lever
2.5
±0.07
dia.
2.35
+0.075
-
0.05
14.5
A
3.6
Operating characteristics
Operating Force
Releasing Force
Overtravel
Movement Differential
OF
RF
OT
MD
FP
OP
Model
Max.
Min.
Min.
Max.
Max.
SS-3GLP
SS-01GLP
6.9
7.7
3.3
±0.1
OP
FP
0.5 N {51 gf}
0.05 N {5 gf}
1.0 mm
0.8 mm
13.6 mm
8.8±0.8 mm
7.3
2.15
8.55
15.5
5.15 9.5
±0.1
19.8
±0.2
2.35
+0.075
dia.
-0.05
3-1.6 dia. holes
0.5
6.4
±0.2
Free Position
Operating Position
●Long
hinge lever
SS-3FL111P-3
t=0.3 Stainless-steel lever
2.5
±0.07
dia.
2.35
+0.075
-
0.05
22.6
A
3.6
Operating characteristics
OP
FP
Model
Max.
Min.
Min.
Max.
Max.
SS-3FL111P-3
0.55 N {56 gf}
0.01 N {1 gf}
1.0 mm
3.0 mm
16.8 mm
8.8±1.5 mm
6.9
7.7
3.3
±0.1
Operating Force
Releasing Force
Overtravel
Movement Differential
Free Position
Operating Position
0.5
6.4
±0.2
OF
RF
OT
MD
FP
OP
7.3
2.35
+0.075
dia.
-0.05
2.15
8.55
15.5
5.15 9.5
±0.1
19.8
±0.2
3-1.6 dia. holes
Note 1. Unless otherwise specified, a tolerance of
±0.4
mm applies to all dimensions.
Note 2. The operating characteristics are for operation in the A direction ( ).
3
SS-P
●Simulated
roller lever
SS-3GL13P
t=0.3 Stainless-steel lever
SS-01GL13P
2.5
±0.07
dia.
2.35
+0.075
-0.05
6.9
7.7
3.3
±0.1
2.35
+0.075
dia.
-0.05
3-1.6 dia. holes
OP
FP
15.8
A
R1.2
3.6
Subminiature Basic Switch
Operating characteristics
Operating Force
Releasing Force
Overtravel
Movement Differential
Free Position
Operating Position
0.5
6.4
±0.2
Model SS-3GL13P SS-01GL13P
Max.
Min.
Min.
Max.
Max.
0.5 N {51 gf}
0.05 N {5 gf}
1.0 mm
0.8 mm
15.5 mm
10.7±0.8 mm
OF
RF
OT
MD
FP
OP
7.3
2.15
8.55
15.5
5.15 9.5
±0.1
19.8
±0.2
S
S
P
Voltage (V)
-
Note 1. Unless otherwise specified, a tolerance of
±0.4
mm applies to all dimensions.
Note 2. The operating characteristics are for operation in the A direction ( ).
Precautions
★Please
refer to "Common Precautions" for correct use.
Cautions
●Soldering
• Connecting to Solder Terminals
Complete the soldering at the iron tip temperature of 350 to
400°C within 5 seconds, and do not apply any external force
for 1 minute after soldering. Soldering at an excessively high
temperature or soldering for more than 5 seconds may
deteriorate the characteristics of the Switch.
• Connecting to PCB terminals
When using automatic soldering baths, we recommend
soldering at 260±5°C within 5 seconds. Make sure that the
liquid surface of the solder does not flow over the edge of
the board.
When soldering terminals manually, complete the soldering
at the iron tip temperature between 350 to 400°C within 3
seconds, and do not apply any external force for 1 minute
after soldering. When applying solder, keep the solder away
from the case of the Switch and do not allow solder or flux to
flow into the case.
Correct Use
●Mounting
Use M2.3 mounting screw with plane washers or spring washers
to securely mount the Switch. Tighten the screws to a torque of
0.23 to 0.26 N·m {2.3 to 2.7 kgf·cm}.
●Using
Micro Loads
Using a model for ordinary loads to open or close the contact of
a micro load circuit may result in faulty contact. Use models that
operate in the following range. However, even when using micro
load models within the following operating range, if inrush
current occurs when the contact is opened or closed, it may
increase the contact wear and so decrease durability. Therefore,
insert a contact protection circuit where necessary. The N-level
reference value applies for the minimum applicable load. This
value indicates the malfunction reference level for the reliability
level of 60% (λ
60
).
(JIS C5003)
The equation,
λ
60
=0.5×10
-6
/operation indicates that the
1
estimated malfunction rate is less than
2,000,000
operations with
a reliability level of 60%.
30
0.16 mA
26 mA
100 mA
24
Operating
range for
general-load
model
SS-3P
Operating range for
micro-load model
SS-01P
12
5
0
0.1
1 mA
1
10
100 mA 160 mA
100
1,000
Current (mA)
4
SS-P
Subminiature Basic Switch
S
S
P
-
•
Application examples provided in this document are for reference only. In actual applications, confirm equipment functions and safety before using the product.
•
Consult your OMRON representative before using the product under conditions which are not described in the manual or applying the product to nuclear control systems, railroad
systems, aviation systems, vehicles, combustion systems, medical equipment, amusement machines, safety equipment, and other systems or equipment that may have a serious
influence on lives and property if used improperly. Make sure that the ratings and performance characteristics of the product provide a margin of safety for the system or
equipment, and be sure to provide the system or equipment with double safety mechanisms.
Note: Do not use this document to operate the Unit.
[i=s]This post was last edited by lising on 2019-6-21 19:32[/i]This experiment is mainly to establish a development environment for the CH549EVT development learning board under KEIL, and try to use "...
[size=4] With the widespread application of embedded systems, the demand for serial communication within the system is getting higher and higher, and the protocols for serial data transmission are als...
This post coincides with Thanksgiving, and here comes another piece of useful information . Special thanks to the ST engineer for sharing.Download PCB source file:For more information and information:...
1. Connection parametersThe connection parameters are Connection interval, Slave latency, and Supervisor timeout.
Connection interval----1.25ms as unit, value range 6~3200 [i.e. 7.5ms~4s]
PS: Mobile p...
I have seen many questions about photodiodes and related circuits on technical forums. I would like to share this with more colleagues. This knowledge is what all analog designers must know.
A typic...
[align=left][color=rgb(51, 51, 51)][font=-apple-system-font, BlinkMacSystemFont, "][size=17px]Today I would like to introduce to you a cartoon tutorial produced by ZTE University - Principles of Dialo...
Nowadays, UC3842 integrated circuits are widely used to form high-performance current-type switching power supply control circuits, which are suitable for offline switching regulated power supplies o...[Details]
Motion controllers usually use two command methods to control servo motors:
1. Digital pulse
This method is similar to the control method of stepper motors. The motion controller sends a ...[Details]
In the field of smart wearable devices, users have put forward higher requirements for the comfort and functionality of the devices, which has promoted the rapid development of flexible wearable an...[Details]
CPU
In terms of CPU selection, domain controllers from various manufacturers are pursuing high-computing chips to achieve L2+ advanced ADAS functions such as NOP/NGP. Currently, NVIDIA Xavier ...[Details]
Electrical detection methods include pulse current method, radio interference voltage method, UHF partial discharge detection technology, dielectric loss analysis method
Electrical detection method...[Details]
The circuit only drives one digital tube, which is a common cathode tube with the common end connected to ground. The segment tube is directly connected to the P2 port of the microcontroller. The mic...[Details]
//《Only Mom Is Good in the World》51 MCU C language program
//2007-5-22Author : Xu Xuejun
//Note that there is a 51 MCU assembly language program correspo...[Details]
1 Use of action flags In the whole control, there are many combined actions. When all action positioning is controlled by photoelectric switches, there are some problems in programming. For example...[Details]
1. Measure the crystal oscillator clock: Use a digital multimeter to measure the voltage at both ends of the crystal oscillator. If the voltage at both ends is half of the power supply voltage or one...[Details]
Mouser Electronics, Inc., the leading global distributor of electronic components that drives innovation through New Product Introduction, is now shipping the Layerscape® LS1046A Freeway (FRWY-LS1046...[Details]
PWM Generator
Introduction
This module creates a pulse width modulated (PWM) voltage between the PWM and REF ports. When the pulse is low, the output voltage is zero; when the pulse...[Details]
introduction
At present, most of the various switching power supplies used in various electrical equipment use indirect DC/DC
conversion circuits
. It has the advantages of good isol...[Details]
introduction
This paper proposes a network camera design based on ARM and POE embedded system. The solution uses AT91RM9200 processor and its peripheral modules as the hardware platform and embedd...[Details]
The oscilloscope has always been an important tool used by engineers to design and debug products. It is also a widely used and basic test instrument for electronic measurement. A tall building start...[Details]
1: First the Makefile.def:
————————————————————————————————————————
In all driver makefiles there is !INCLUDE $(_MAKEENVROOT)makefile.def
Find (_MAKEENVROOT) makefile.def where C:WIN...[Details]
DIY/Open Source Hardware
京公网安备 11010802033920号
EEWORLD
