Input Characteristics For Enable / Disable Function (Pad 8)
Parameter
Enable Voltage (High) or open circuit
Disable Voltage (Low) Output Tri-stated
(Vih)
(Vil)
Minimum
70% Vcc
-
Nominal
-
-
Maximum
-
30% Vcc
Units
Vdc
Vdc
Notes
10
Input Characteristics For Voltage Control (Pad10)
Parameter
Control Voltage Range (Vcc = 3.3V)
Frequency Tuning
Linearity
Input Impedance
Modulation Bandwidth (3dB)
Slope
(Vc)
Minimum
0.3
±10
±5
100K
10
Nominal
1.65
-
-
-
-
Positive
Maximum
3.0
-
-
-
-
Units
Vdc
ppm
%
Ohm
KHz
Notes
11
LVCMOS Output Characteristics
LOAD
Voltage
(High)
(Low)
Current
(High)
(Low)
Duty Cycle at 50% of Vcc
Rise / Fall Time 10% to 90%
Parameter
(Voh)
(Vol)
(Ioh)
(Iol)
Minimum
-
90%Vcc
-
-4
-
45
-
Nominal
15
-
-
-
-
50
-
Maximum
-
-
10%Vcc
-
4
55
8
Units
pF
Vdc
Vdc
mA
mA
%
ns
Notes
12
Clipped Sinewave Output Characteristics
Load
Output Load Resistance
Output Load Capacitance
Output Voltage (< 40 MHz)
Output Voltage (> 40 MHz)
Notes:
1.
Frequency stability vs. change in temperature. [±(Fmax – Fmin)/2.Fo].
2.
Inclusive of frequency stability, supply voltage change (±1%), aging, for 24 hours.
3.
Over twenty years
4. TCXO: Initial calibration @ 25°C. Specifications at time of shipment after 48 hours of operation.
5. Frequency change after reciprocal temperature ramped over the operating range. Frequency measured before and after at 25°C.
6 Inclusive of calibration @ 25°C, frequency vs. change in temperature, change in supply voltage (±5%), load change (±5%), reflow soldering process
and 20 years aging.
7. For best in application performance, careful selection of an external power source is critical. Select an external regulator that meets or exceeds to
following specifications regarding voltage regulation tolerance, initial accuracy, temperature coefficient, voltage noise, and low voltage noise density
Factory Test Conditions:
Initial Accuracy ±2mv, Noise (0.1Hz to 10 KHz) 15uV p-p, Voltage Noise Density = 50nV/srt Hz, Temperature Coefficient
< 5ppmºC.
8. Phase noise measurements Fo = 20 MHz, other frequencies may vary by 20log F/20MHz.
9. Typical start up time for the frequency range of 12.8 MHz to 25 MHz <330 us.
10. Leave Pad 8 unconnected if enable / disable function is not required. When tri-stated, the output stage is disabled but the oscillator and compensation
circuit are still active (current consumption < 1mA).
11. Additional pull ranges are available; please contact the factory for additional information.
12.
Attention: To achieve optimal frequency stability, and in some cases to meet the specification stated on this data sheet, it is required that the circuit connected to this TCXO output
must have the equivalent input capacitance that is specified by the nominal load capacitance. Deviations from the nominal load capacitance will have a graduated effect on the stability
Brothers, I have a question for you. I used NCP1252A chip to make a dual-tube forward switching power supply. Today I measured the voltage of the chip CS pin and it reached 1.28V, but the power supply...
1、watchdogtimer（WDT_A)
Watchdog timer?
Watchdog Timer 32-bit timer, can be used as a watchdog or as an interval timer.Before you watch, ask yourself a few questions
a. Does the watchdog depend on the ...
I have a question. Why does the 12V power inlet of the car's central control need an LC filter circuit formed by a 330uH inductor and a 3300uF large capacitor to filter low-frequency interference? Is ...
Let's take you to play with mobile application creation, timing function, delay function, push function, smart scene function. If you need to make smart curtains, you can customize the scene according...
Power technology
京公网安备 11010802033920号
EEWORLD
