3GPW14G-C-30M-800.000 datasheet, PDF

Datasheet> All Categories > Passive components> oscillator> 3GPW14G-C-30M-800.000

3GPW14G-C-30M-800.000: DescriptionLVPECL Output Clock Oscillator, 800MHz Nom, ROHS COMPLAINT, DIL-14/4; CategoryPassive components oscillator; File Size115KB，1 Pages; ManufacturerEuroquartz; Websitehttp://www.euroquartz.co.uk/; Environmental Compliance

Download Datasheet Parametric View All

3GPW14G-C-30M-800.000 Overview

LVPECL Output Clock Oscillator, 800MHz Nom, ROHS COMPLAINT, DIL-14/4

3GPW14G-C-30M-800.000 Parametric

Parameter Name	Attribute value
Is it lead-free?	Lead free
Is it Rohs certified?	conform to
Reach Compliance Code	compliant
Maximum control voltage	2 V
Minimum control voltage	1.3 V
maximum descent time	7 ns
Frequency Adjustment - Mechanical	NO
Frequency offset/pull rate	30 ppm
frequency stability	100%
Installation features	THROUGH HOLE MOUNT
Nominal operating frequency	800 MHz
Maximum operating temperature	70 °C
Minimum operating temperature
Oscillator type	LVPECL
Output load	50 OHM
physical size	20.2mm x 12.8mm x 5.08mm
longest rise time	7 ns
Maximum supply voltage	3.465 V
Minimum supply voltage	3.135 V
Nominal supply voltage	3.3 V
surface mount	NO
maximum symmetry	55/45 %
Base Number Matches	1

Preview

Download Datasheet

View All

EURO

QUARTZ

14 pin Dual-in-Line

Frequency range 750kHz to 800MHz

LVPECL Output

Supply Voltage 3.3 VDC

Phase jitter 2.35ps typical

Pull range from ±30ppm to ±150ppm

DESCRIPTION

GPW14 VCXOs are packaged in an industry-standard 14 pin dual-in-

line package. Typical phase jitter for GPW series VCXOs is 2.35ps.

Output is LVPECL. Applications include phase lock loop, SONET/ATM,

set-top boxes, MPEG , audio/video modulation, video game consoles

and HDTV.

SPECIFICATION

Frequency Range:

Supply Voltage:

Output Logic:

RMS Period Jitter:

Peak to Peak Jitter:

Phase Jitter:

Initial Frequency Accuracy:

Output Voltage HIGH (1):

Output Voltage LOW (0):

GPW14 PECL VCXO

750.0kHz to 800.0MHz

OUTLINE & DIMENSIONS

Pulling Range:

Control Voltage Range:

Temperature Stability:

Output Load:

Rise/Fall Times:

Duty Cycle:

Start-up Time:

Current Consumption:

Static Discharge Protection:

Storage Temperature:

Ageing:

Enable/Disable:

RoHS Status:

750.0kHz to 800.0MHz

3.3 VDC ±5%

LVPECL

4.3ps typical

27.0ps typical

2.35ps typical

Tune to the nominal frequency

with Vc= 1.65 ±0.2VDC

Vdd-1.025V minimum

Vdd-0.880V maximum

Vdd-1.810V minimum

Vdd-1.620V maximum

(RL=50 to Vdd-2V)

From ±30ppm to ±150ppm

1.65 ±0.35 Volts

See table

50W into Vdd or Thevenin equiv.

0.5ns typ., 0.7ns max.

20% Vdd to 80% Vdd

50% ±5%

(Measured at Vdd-1.3V)

10ms maximum, 5ms typical

75mA maximum at 212.5MHz

80mA maximum at 622.08MHz

2kV maximum

-55° to +150°C

±2ppm per year maximum

Not implemented, 4 pin package

Fully compliant or non-compliant

versions available

PART NUMBERING

Example:

3GPW14G-B-80N-60.000

FREQUENCY STABILITY

Stability Code Stability ±ppm Temp. Range

0°~+70°C

100

0°~+70°C

-40°~+85°C

100

-40°~+85°C

If non-standard frequency stability is required

Use ‘I’ followed by stability, i.e. I20 for ±20ppm

Supply Voltage

3 = +3.3V

Series Designator

GPW14

RoHS Status

G = RoHs compliant

Blank = RoHS non-compliant

Stability over temperature range

(See table)

Pullability in ±ppm

Pullability determinator

N = minimum

M = maximum

T = Typical

Frequency in MHz

EUROQUARTZ LIMITED Blacknell Lane CREWKERNE Somerset UK TA18 7HE

Tel: +44 (0)1460 230000 Fax: +44 (0)1460 230001 info@euroquartz.co.uk www.euroquartz.co.uk

Recommended Resources

An electric motor's electrode automatic regulator circuit

Fuse blown sound and light alarm circuit 3

Frequency doubling circuit composed of diodes

555 constitutes a 5min start-up delay circuit

DN35 typical application circuit diagram d

Telephone schematic diagram 03

USB communication design example based on CH559 MCU Android AOA protocol: Wired communication between the MCU and the Android system can be achieved through the Micro USB interface on the Android device. There are two main ways: ① The Android device acts as the host, and th...; 宋元浩 Domestic Chip Exchange

Technical article | How to use J-Link to burn SPI Flash: J-Link not only supports the burning of the Flash on the MCU , but also can directly burn the SPI Flash through the SPI protocol. Because the SPI protocol is used , even if the MCU connected to the SP...; MamoYU Integrated technical exchanges

Low power consumption comparison between STM8L and MSP430: After comparing actual products, STM8L's low power consumption is far better than MSP430. I'll record it here. Different opinions are welcome. The test environment is as follows: 1. External crystal o...; Aguilera Microcontroller MCU

Drag-and-drop stepper motor programmable controller + PLC-like: ...; net2uizoo DIY/Open Source Hardware

Pengfeng Technology RVBoards-Nezha (RISC-V SBC) Allwinner Development Board Introduction 4: Perf-V IDE Introduction and Installation Instructions...; 火辣西米秀 Domestic Chip Exchange

Share the SPWM code written by DSPF28335 with everyone: The source program is as follows:/** main.c*/ #include "DSP28x_Project.h"// Device Headerfile and Examples Include File // Prototype statements for functions found within this file. void InitEPwm1Exam...; fish001 DSP and ARM Processors

Shortcut: 00 01 02 03 04 05 06 07 08 09 0A 0C 0F 0J 0L 0M 0R 0S 0T 0Z 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 1H 1K 1M 1N 1P 1S 1T 1V 1X 1Z 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 2G 2K 2M 2N 2P 2Q 2R 2S 2T 2W 2Z 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F 3G 3H 3J 3K 3L 3M 3N 3P 3R 3S 3T 3V 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4M 4N 4P 4S 4T 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5E 5G 5H 5K 5M 5N 5P 5S 5T 5V 60 61 62 63 64 65 66 67 68 69 6A 6C 6E 6F 6M 6N 6P 6R 6S 6T 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7M 7N 7P 7Q 7V 7W 7X 80 81 82 83 84 85 86 87 88 89 8A 8D 8E 8L 8N 8P 8S 8T 8W 8Y 8Z 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9F 9G 9H 9L 9S 9T 9W

Popular Components