2. Parameter verified during line and load regulation tests. Regulation is specified for 10% to 100% loading on all outputs.
3. Auxiliary output regulation is not maintained if main output load is less than 10%.
4. Auxiliary outputs require at least 10% loading for specified regulation. Voltage may increase at lighter loads and is ultimately limited by overvoltage zener diodes.
5.Unless otherwise specified, “Rated” load is 20W on the main (+5 volt) output and 15 watts each on the auxiliary (±15 volt) outputs. Load currents of up to 5A and ±1.5A on the main
and auxiliary outputs respectively are acceptable as long as the total output power does not to exceed 50 watts. Values in [ ] brackets reflect “-H" option SEE hardened version
performance. The "-H" option incorporates alternative FET technologies providing a >82 MeV•cm2 /mg (Gold Ion) SEE capability to the design.
6. Guaranteed for a D.C. to 20MHz bandwidth. Tested using a 20kHz to 10MHz bandwidth.
7. Capacitive load may be any value from 0 to the maximum limit without compromising dc performance. A capacitive load in excess of the maximum limit may interfere with the
proper operation of the converter’s overload protection, causing erratic behavior during turn-on.
8. Overload power dissipation is defined as the device power dissipation with the load set such that VOUT = 90% of nominal.
9. Load step transition time ? 10
μs.
10. Recovery time is measured from the initiation of the transient to where VOUT has returned to within ±1% of its steady state value.
11. Line step transition time ? 100
μs.
12. Turn-on delay time from either a step application of input power or a logic low to a logic high transition on the inhibit pin (pin 3) to the point where VOUT = 90% of nominal.
13. Load Regulation relative to output voltage at 50% rated load.
14. Line Regulation relative to output voltage at 120Vdc input.
15. For operation at temperatures between +85°C and +125°C, derate power linearly from 50 watts to zero. Parameter limits are not guaranteed.
Live broadcast time: November 24, 14:00-15:30Live broadcast topic: Detailed explanation of NXP embedded human-machine interface solutionsSpeech document: Click here to downloadWatch replay: Click to w...
I recently completed a brushless DC motor speed control project. I consulted various blogs and papers written by experts. Here I will only make a small summary; FOC (Field Oriented Control) is a mathe...
PyPortal Pynt clock/weather display using CircuitPython, with RTC and NTP automatic time synchronization support.https://github.com/imekon/weather-clock...
Preface
This guide document is applicable to the development environment:
Windows development environment: Windows 7 64bit, Windows 10 64bit
Linux development environment: Ubuntu 14.04.3 64bit
Virtual...
Gizwits is positioned as smart hardware. The direction is that you use our hardware. We can provide us with software APIs. Everything is ready for you. You just need to know how to use it. It has abso...
Author: Karl-Heinz Steinmetz of Texas Instruments. Translated from TI blog Technology availability, market and environmental regulations, and infrastructure build-out are aligning to achieve the lo...[Details]
0 Introduction
IIR filters are not easy to make into linear phase, but FIR filters can be made into linear phase as long as certain conditions are met. The requirement for linear phase is ...[Details]
1. Fault phenomenon and treatment A 110kV substation in a certain place is undergoing comprehensive automation transformation. There are five groups of 110kv and 10kv voltage transformers, three gro...[Details]
China Energy Storage Network News:
At 10:04 on May 6, the load of the Guangdong Power Grid Company of the Southern Power Grid exceeded 100 million kilowatts for the first time this year, an i...[Details]
Many systems require low-power power supplies in addition to mains power. A typical example is that when the analog front-end amplifier requires ±5V power, the main digital circuit only requires +5V p...[Details]
Abstract A high-brightness strobe light with adaptive temperature and wide voltage range based on HV9910 is designed. It can work with high brightness in a wide voltage range of 10 to 50 V by utili...[Details]
MAX8982A/MAX8982X are complete power management ICs for the latest LTE/WCDMA/GSM/GPRS/EDGE data cards on the new ICERA platform (E400/E450). The MAX8982 operates from a 4.1V to 5.5V power supply and c...[Details]
Recently, the fifth episode of CCTV's large-scale documentary "The Foundation of a Strong Country" was broadcast, which mentioned Xiaomi's self-developed Surge chip. According to CCTV reports, Dr....[Details]
The full name of Car Reversing Aid Systems is "Car Reversing Anti-collision Radar", also known as "Parking Assist Device". It is a car parking safety auxiliary device that can inform the driver of su...[Details]
●Try to use original batteries
Using original batteries is the most important thing to ensure your safety. Nokia once claimed that there have been more than 20 mobile phone battery explosi...[Details]
On September 4, Zhongjing Electronics issued an announcement on the progress of establishing an industrial fund. Zhongjing Electronics held the 31st meeting of the 4th Board of Directors on July 13...[Details]
1. Analysis of Misunderstandings of LED Heat Dissipation The misunderstandings of LED heat dissipation are mainly reflected in the following aspects: 1. The internal quantum efficiency is not h...[Details]
Precautions for use: 1. The transfer switch must be placed in the position where the measurement gear is required, and there must be no mistake. When measuring voltage, if the resistance or current s...[Details]
On December 20, State Grid Corporation of China held a press conference in Beijing on "Stabilizing Investment to Ensure People's Livelihood and Promoting High-quality Development of the Grid", anno...[Details]
This article introduces how to use an oscilloscope. There are many types and models of oscilloscopes with different functions. The 20MHz or 40MHz dual-trace oscilloscopes are more commonly used in ...[Details]