3. Epoxy meniscus may extend about 1mm (0.040”) down the leads.
Device Selection Guide
Iv (cd) @ 20mA
Part Number
HLMP-CW18-VY0xx
HLMP-CW19-VY0xx
HLMP-CW28-TW0xx
HLMP-CW29-TW0xx
HLMP-CW38-SV0xx
HLMP-CW39-SV0xx
Notes:
1. Tolerance for luminous intensity measurement is +/- 15%
2. The luminous intensity is measured on the mechanical axis of the lamp package.
3. The optical axis is closely aligned with the package mechanical axis.
4. LED light output is bright enough to cause injuries to the eyes. Precautions must be taken to prevent looking directly at the LED without proper safety
equipment.
Typ. Viewing Angle
Min.
15°
15°
23°
23°
30°
30°
4.20
4.20
2.50
2.50
1.90
1.90
Typ.
6.40
6.40
3.80
3.80
3.00
3.00
Standoff Leads
No
Yes
No
Yes
No
Yes
Package
Dimension
A
B
A
B
A
B
Part Numbering System
L M P - C W XX - X X X XX
Mechanical Option
00: Bulk
DD: Ammo Pack
Color Bin Options
0: Full color bin distribution
Maximum Intensity Bin Limit
0: No maximum intensity bin limit
Minimum Intensity Bin Limit
Refer to Device Selection Guide
Viewing Angle
18: 15 without standoffs
19: 15˚ with standoffs
28: 23˚ without standoffs
29: 23˚ with standoffs
38: 30 ˚ without standoffs
39: 30 ˚ with standoffs
Color Options
W: White
Package Options
C: T-1 3/4
2
Absolute Maximum Ratings (T
A
= 25°C)
Parameter
DC Forward Current
[1]
Peak Forward Current
[2]
Average Forward Current
Power Dissipation
LED Junction Temperature
Operating Temperature Range
Storage Temperature Range
Wave Solder Temperature
[3]
Solder Dipping Temperature
[3]
Notes:
1. Derate linearly as shown in Figure 4.
2. Duty Factor 30%, 1 KHz
3. 1.59 mm (0.060 inch) below body
Value
30
100
30
120
130
-40 to +85
-40 to +100
250 for 3 secs
260 for 5secs
Units
mA
mA
mA
mW
°C
°C
°C
°C
°C
Electrical/Optical Characteristics (T
A
= 25
o
C)
Parameters
Forward voltage
Capacitance
Reverse Voltage
[1]
Thermal resistance
Viewing Angle
[2]
CW18/CW19
CW28/CW29
CW38/CW39
Symbol
V
F
C
V
R
Rθ
J-PIN
2θ
1/2
15
23
30
0.31
0.32
I
F
= 20 mA
Minimum Typical
3.4
53
0.6
240
Maximum Units
4.0
V
pF
V
o
C/W
Test Condition
I
F
= 20 mA
V
F
=0, f=1 MHz
I
R
= 10
µA
LED Junction to cathode lead
I
F
= 20 mA
Degree
Chromaticity Coordinate
[3]
X
Y
Notes:
2. 2
θ
1/2
is the off-axis angle where the luminous intensity is ½ the on axis intensity
1. The reverse voltage of the product is equivalent to the forward voltage of the protective chip at I
R
= 10
µ
A
3. The chromaticity coordinates are derived from the CIE 1931 Chromaticity Diagram and represent the perceived color of the device.
1. Let's first learn about the flyback converter. 1. Basic flyback circuit: 400942[/attach]2. Working principle: 51)][font=-apple-system-font, BlinkMacSystemFont, "][size=17px]The polarity of the prim...
Simulation of Patch Array Antenna with TR module ' s effect
Chengcheng Xie Bhargava Anurag
Agilent TechnologiesEEsofEDA
Abstract: In this paper,a new simulation method of patch arrayantennais introduc...
Received a strange packagedismantle!Then I found a bag of strange black powder with some grayish white in it.
My first reaction was WTF is moldy?!
Then I turned down and saw a long strip of toilet pap...
The continuous upgrading of intelligent
driving technology will not only improve safety by at least one order of magnitude, but also become the core selling point of the next generation of in...[Details]
As the requirements and dependence of automobiles on control systems increase, the design module of AD sampling has become an important component of automobile controllers. The results of AD sampli...[Details]
and the host Bluetooth address) After receiving the scan request, the slave replies SCAN_RSP PDU on the same channel. After receiving the scan reply information, the host sends CONNECT_REQ PDU info...[Details]
The important component of the brushless motor is the strong magnet, which is basically made of neodymium iron boron. Due to its physical properties, neodymium magnets will
It will slowly dema...[Details]
Question: Does a switching power supply (DC/DC converter) really degrade the performance of an ADC?
Answer:
Engineers generally believe that switching power supplies will degrade ADC...[Details]
In recent years, the TV industry has undergone many changes, and the color TV market has changed from an incremental market to a stock market. In the new market environment, "trading market with pr...[Details]
Lithium-ion batteries have a specific charging cycle after which they cannot provide the same battery life. To address this issue, Samsung has introduced a new "Protect Battery" feature in the...[Details]
According to Yonhap News Agency, as Samsung Display decided to stop producing liquid crystal panels (LCD) from next year, the industry has expressed great interest in the expansion of market share of...[Details]
Angle displacement sensors are electronic components that use angle changes to locate the position of an object. They are suitable for servo systems of automobiles, engineering machinery, space device...[Details]
Apple has released iOS 15 early this morning, but due to limited time, Apple was unable to introduce all the new features in the new system one by one. The following are the new features and featur...[Details]
On July 25, all battery compartments of CNNC Huineng's 100MW/200MWh energy storage power station project in Chongqing Xiyong Comprehensive Bonded Zone completed rated charging and discharging, mark...[Details]
In the previous section, we talked about how to implement the tasklet mechanism
http://blog.csdn.NET/morixinguan/article/details/69666935
In this section, we will implement th...[Details]
Today I spent half a day learning how to port madplay. Thanks to the rich online resources, I was able to find solutions to one problem after another.
After returning from shopping, I immediat...[Details]
Mobile Industrial Robots (MiR), a global leader in the mobile robot market, has released a new top module, MiR250 Hook. This new product is suitable for the MiR250 Autonomous Mobile Robot (AMR) and i...[Details]
MEMS sensors
京公网安备 11010802033920号
EEWORLD
