EEWORLDEEWORLDEEWORLD

Part Number

Search

T3-36241G

Description
Toggle Switch, DPDT, On-(on), Momentary, 5A, 28VDC, 6 PCB Hole Cnt, Solder Terminal, Toggle Actuator, Through Hole-straight
CategoryMechanical and electronic products    switch   
File Size330KB,2 Pages
ManufacturerOTTO
Websitehttp://www.ottoexcellence.com
Download Datasheet Parametric View All

T3-36241G Overview

Toggle Switch, DPDT, On-(on), Momentary, 5A, 28VDC, 6 PCB Hole Cnt, Solder Terminal, Toggle Actuator, Through Hole-straight

T3-36241G Parametric

Parameter NameAttribute value
MakerOTTO
Reach Compliance Codeunknown
Actuator angle28 deg
Actuator length1.16 inch
Actuator typeTOGGLE
Other featuresLOCKED IN KEYWAY SIDE
body width13.589 mm
Body length or diameter14.605 mm
Nozzle length0.47 inch
Casing type15/32-32
center contact materialSILVER
Center contact platingGOLD
Contact (AC) maximum rated load I2A@115VAC
Contact (AC) maximum rated R load5A@115VAC
Maximum contact current (AC)5 A
Maximum contact current (DC)5 A
Contact (DC) maximum rated R load5A@28VDC
Contact functionON-(ON)
Maximum contact voltage (AC)115 V
Maximum contact voltage (DC)28 V
Dielectric withstand voltage1050VRMS V
Electrical life30000 Cycle(s)
End contact materialSILVER
End contact platingGOLD
Manufacturer's serial numberT3
Installation featuresTHROUGH HOLE-STRAIGHT
Maximum operating temperature85 °C
Minimum operating temperature-65 °C
PCB hole count6
sealMOLDED
surface mountNO
Switch actionMOMENTARY
switch functionDPDT
Switch typeTOGGLE SWITCH
Terminal length0.09 inch
Termination typeSOLDER
Base Number Matches1
Vivado prompts [Synth 8-91] ambiguous clock in event control Problem Cause
Comprehensive prompt [Synth 8-91] ambiguous clock in event control. Later it was found that the reason was because the if was written in the always and the else was omitted....
littleshrimp FPGA/CPLD
Simulation and Testbench Design.zip
Simulation and Testbench Design.zip...
zxopenljx EE_FPGA Learning Park
I downloaded a source code from the Internet. I don't know what software it was developed with. The file type is shown in the picture. Please help me take a look.
[i=s]This post was last edited by Shenzhen Xiaohua on 2020-12-13 12:15[/i]I downloaded a source code from the Internet. I don't know what software it was developed with. As shown in the figure below, ...
深圳小花 MCU
How to choose MOS tube for low power motor
My motor has two operating voltages, 12V and 7V. The working current is 800mA at 7V. When starting, it needs to run at 12V for a while, and then switch to 7V. I want to use MOS tube to control the ope...
bigbat Motor Drive Control(Motor Control)
IC Industry Base
Entering the seventh year: China's three major IC industrial bases move from dream to reality     Author: He Xudong, Sun Changxu       In Shenzhen, more and more newly established IC companies want to...
hkn FPGA/CPLD
3D Printer Project—STM32F750 Startup Program (Part 2)
# 3D Printer Project - STM32F750 Startup Program (Part 2) ## Overview Since the chip STM32F750N8H6 used in STM32F7508-DK belongs to the STMicroelectronics Arm Cortex-M7 core, the built-in FLASH is onl...
caxfan DigiKey Technology Zone

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号