MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
9 Bit Magnitude Comparator
The MC10E/100E166 is a 9-bit magnitude comparator which
compares the binary value of two 9-bit words and indicates whether one
word is greater than, or equal to, the other.
MC10E166
MC100E166
9-BIT MAGNITUDE
COMPARATOR
•
1100ps Max. A=B
•
Extended 100E VEE Range of – 4.2V to – 5.46V
•
75kΩ Input Pulldown Resistors
Pinout: 28-Lead PLCC
(Top View)
B2
25
A3
B3
NC
VEE
A4
B4
A5
26
27
28
1
2
3
4
5
B5
6
A6
7
B6
8
A7
9
B7
10
A8
11
B8
A2
24
B1
23
A1
22
B0
21
A0
20
VCCO
19
18
17
16
15
14
13
12
A=B
NC
VCC
B>A
VCCO
A>B
NC
A0 – A8
9
A>B
FN SUFFIX
PLASTIC PACKAGE
CASE 776-02
LOGIC DIAGRAM
COMPARATOR
* All VCC and VCCO pins are tied together on the die.
A=B
PIN NAMES
Pin
A0 – A8
B0 – B8
A>B
B>A
A=B
Function
A Data Inputs
B Data Inputs
A Greater than B Output
B Greater than A Output
A Equal to B Output
(active-LOW)
B0 – B8
9
B>A
7/96
©
Motorola, Inc. 1996
2–1
REV 3
MC10E166 MC100E166
OUTLINE DIMENSIONS
FN SUFFIX
PLASTIC PLCC PACKAGE
CASE 776–02
ISSUE D
0.007 (0.180)
U
T L –M
M
B
-N-
Y BRK
M
S
N
S
S
0.007 (0.180)
T L –M
N
S
D
Z
-L-
-M-
W
28
1
D
X
VIEW D-D
G1
0.010 (0.250)
S
V
T L –M
S
N
S
A
Z
R
0.007 (0.180)
0.007 (0.180)
M
T L –M
T L –M
S
N
N
S
H
S
0.007 (0.180)
M
T L –M
S
N
S
M
S
C
E
G
G1
0.010 (0.250)
S
K1
0.004 (0.100)
J
-T-
SEATING
PLANE
K
F
VIEW S
0.007 (0.180)
M
VIEW S
T L –M
S
T L –M
S
N
S
N
S
NOTES:
1. DATUMS -L-, -M-, AND -N- DETERMINED
WHERE TOP OF LEAD SHOULDER EXITS
PLASTIC BODY AT MOLD PARTING LINE.
2. DIM G1, TRUE POSITION TO BE MEASURED
AT DATUM -T-, SEATING PLANE.
3. DIM R AND U DO NOT INCLUDE MOLD FLASH.
ALLOWABLE MOLD FLASH IS 0.010 (0.250)
PER SIDE.
4. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
5. CONTROLLING DIMENSION: INCH.
6. THE PACKAGE TOP MAY BE SMALLER THAN
THE PACKAGE BOTTOM BY UP TO 0.012
(0.300). DIMENSIONS R AND U ARE
DETERMINED AT THE OUTERMOST
EXTREMES OF THE PLASTIC BODY
EXCLUSIVE OF MOLD FLASH, TIE BAR
BURRS, GATE BURRS AND INTERLEAD
FLASH, BUT INCLUDING ANY MISMATCH
BETWEEN THE TOP AND BOTTOM OF THE
PLASTIC BODY.
7. DIMENSION H DOES NOT INCLUDE DAMBAR
PROTRUSION OR INTRUSION. THE DAMBAR
PROTRUSION(S) SHALL NOT CAUSE THE H
DIMENSION TO BE GREATER THAN 0.037
(0.940). THE DAMBAR INTRUSION(S) SHALL
NOT CAUSE THE H DIMENSION TO BE
SMALLER THAN 0.025 (0.635).
DIM
A
B
C
E
F
G
H
J
K
R
U
V
W
X
Y
Z
G1
K1
INCHES
MIN
MAX
0.485 0.495
0.485 0.495
0.165 0.180
0.090 0.110
0.013 0.019
0.050 BSC
0.026 0.032
0.020
—
0.025
—
0.450 0.456
0.450 0.456
0.042 0.048
0.042 0.048
0.042 0.056
—
0.020
2°
10°
0.410 0.430
0.040
—
MILLIMETERS
MIN
MAX
12.32 12.57
12.32 12.57
4.20
4.57
2.29
2.79
0.33
0.48
1.27 BSC
0.66
0.81
0.51
—
0.64
—
11.43
11.58
11.43
11.58
1.07
1.21
1.07
1.21
1.07
1.42
—
0.50
2°
10°
10.42 10.92
1.02
—
ECLinPS and ECLinPS Lite
DL140 — Rev 4
2–3
MOTOROLA
MC10E166 MC100E166
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola
data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”
must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola and
are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
Opportunity/Affirmative Action Employer.
How to reach us:
USA/EUROPE/Locations Not Listed:
Motorola Literature Distribution;
P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 or 602–303–5454
MFAX:
RMFAX0@email.sps.mot.com – TOUCHTONE 602–244–6609
INTERNET:
http://Design–NET.com
JAPAN:
Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center,
3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–81–3521–8315
ASIA/PACIFIC:
Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
◊
MOTOROLA
2–4
*MC10E/D*
MC10E166/D
ECLinPS and ECLinPS Lite
DL140 — Rev 4