brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without
notice.
www.latticesemi.com
1
isp22v10a_03.0
Lattice Semiconductor
ispGAL22V10AV/B/C Data Sheet
ispGAL Architecture
Output Logic Macrocell (OLMC)
The ispGAL22V10A has a variable number of product terms per OLMC. Of the ten available OLMCs, two OLMCs
have access to eight product terms (pins 17 and 27), two have ten product terms (pins 18 and 26), two have twelve
product terms (pins 19 and 25), two have fourteen product terms (pins 20 and 24), and two OLMCs have sixteen
product terms (pins 21 and 23). In addition to the product terms available for logic, each OLMC has an additional
product-term dedicated to output enable control.
The output polarity of each OLMC can be individually programmed to be true or inverting, in either combinatorial or
registered mode. This allows each output to be individually configured as either active high or active low.
A
D LL
IS
C DE
O
VI
N
TI CE
N
S
U
ED
Figure 2. Output Logic Macrocell
AR
D
Q
The ispGAL22V10A has a product term for Asynchronous Reset (AR) and a product term for Synchronous Preset
(SP). These two product terms are common to all registered OLMCs. The Asynchronous Reset sets all registers to
zero any time this dedicated product term is asserted. The Synchronous Preset sets all registers to a logic one on
the rising edge of the next clock pulse after this product term is asserted.
NOTE: The AR and SP product terms will force the Q output of the flip-flop into the same state regardless of the
polarity of the output. Therefore, a reset operation, which sets the register output to a zero, may result in either a
high or low at the output pin, depending on the pin polarity chosen.
4 TO 1
MUX
CLK
Q
SP
2 TO 1
MUX
Output Logic Macrocell Configurations
Each of the Macrocells of the ispGAL22V10A has two primary functional modes: registered, and combinatorial I/O.
The modes and the output polarity are set by two bits (S0 and S1), which are normally controlled by the logic com-
piler. Each of these two primary modes, and the bit settings required to enable them, are described below and on
the following page.
Registered
In registered mode the output pin associated with an individual OLMC is driven by the Q output of that OLMC’s D-
type flip-flop. Logic polarity of the output signal at the pin may be selected by specifying that the output buffer drive
either true (active high) or inverted (active low). Output tri-state control is available as an individual product-term for
each OLMC, and can therefore be defined by a logic equation. The D flip-flop’s /Q output is fed back into the AND
array, with both the true and complement of the feedback available as inputs to the AND array.
2
Lattice Semiconductor
ispGAL22V10AV/B/C Data Sheet
NOTE: In registered mode, the feedback is from the /Q output of the register, and not from the pin; therefore, a pin
defined as registered is an output only, and cannot be used for dynamic I/O, as can the combinatorial pins.
Combinatorial I/O
In combinatorial mode the pin associated with an individual OLMC is driven by the output of the sum term gate.
Logic polarity of the output signal at the pin may be selected by specifying that the output buffer drive either true
(active high) or inverted (active low). Output tri-state control is available as an individual product-term for each out-
put, and may be individually set by the compiler as either “on” (dedicated output), “off” (dedicated input), or “prod-
uct-term driven” (dynamic I/O). Feedback into the AND array is from the pin side of the output enable buffer. Both
polarities (true and inverted) of the pin are fed back into the AND array.
For an RFID system, its frequency band concept refers to the frequency range of the tag signal that the reader sends, receives and reads through the antenna. From the application concept, the working ...
Learn Industrial ARM with Sitara AM6x Training Series : https://training.eeworld.com.cn/course/5272This training looks at differentiation in the Sitara AM654x (AM6546, AM6548) processor architecture a...
"Embedded System Reliability Design Technology and Case Analysis" introduces which parts of embedded system design are most likely to cause reliability risks, and how to prevent them from the design. ...
Abstract: Aiming at the frequency selective channel fading and hardware implementation constraints faced by broadband multi-antenna millimeter wave systems, a digital-analog hybrid beamforming algorit...
Metering Devices and Applications Selection of Differential Pressure Gas Flowmeters Hu Haiyan (Metering Station of Technical Inspection Station of Hekou Oil Production Plant, Shengli Oilfield, Shando...[Details]
Surface electroplating of piston rings has always been a widely used process. The high-frequency switching power supplies and graded thyristor rectifiers produced by the factory are widely used in...[Details]
In March last year, Redmi launched its first true wireless headset - Redmi True Wireless Bluetooth Earphones AirDots, priced at only 99.9 yuan. In just 6 months, the cumulative sales exceeded ...[Details]
This year, affected by various factors, the global stock market has continued to be sluggish, and the three major A-share indices have not been immune. As of March 11, the Shanghai Composite Index fe...[Details]
On April 27, the National Energy Solar Power Research and Development (Experimental) Center successfully carried out the first high voltage ride-through test of photovoltaic inverters in China. The...[Details]
Abstract:
FAN7710V is a new IC that integrates the ballast control circuit and half-bridge high-side and low-side power MOSFETs on the same chip. The energy-saving lamp ballast based on FAN77...[Details]
1. Question about GPIO: The IO port of STM32 is initialized as input floating, so is the pin high or low? Answer: It is neither high nor low, floating means it is not used. 2. Question about port mult...[Details]
The design of the new generation of LED driver ICs must break the traditional DC/DC topology design concept. For example, constant power is used, and constant frequency and constant current control is...[Details]
What are the speech recognition algorithms?
This article lists several different speech recognition algorithms.
The first one: algorithm based on dynamic time warping
It is still the...[Details]
Host environment
Windows + vmware (redhat9.0)
The IP allocation is as follows:
ARM development board: 192.168.4.151
Windows: 192.168.4.44
Redhat9.0: 192.168.4.150
Building...[Details]
SMA Japan (Minato-ku, Tokyo), the Japanese subsidiary of German SMA Solar Technology, announced on February 24 that a 16MW photovoltaic power plant has adopted a small photovoltaic inverter (PCS) w...[Details]
Today, a piece of news about a Tesla
robot
attacking an engineer went viral online, causing a stir in public opinion.
The popularity of the related topic not only topped Baidu's hot se...[Details]
The rapid development and success of the Internet has promoted the development and application of Ethernet technology, covering a wide range of fields, such as traditional industrial control, informa...[Details]
In most processors after ARM V4 and V4T, the interrupt vector table can have two locations: one is 0 and the other is 0xffff0000. This can be controlled by the V bit (bit ) in the CP15 coprocessor ...[Details]