TSP7N80M/TSF7N80M
TSP7N80M/TSF7N80M
800V N-Channel MOSFET
General Description
This Power MOSFET is produced using Truesemi‘s
advanced planar stripe DMOS technology.
This advanced technology has been especially tailored to
minimize on-state resistance, provide superior switching
performance, and withstand high energy pulse in the
avalanche and commutation mode. These devices are well
suited for high efficiency switched mode power supplies,
active power factor correction based on half bridge
topology.
Features
• 7.0A,800V,Max.R
DS(on)
=1.6 Ω @ V
GS
=10V
• Low gate charge(typical 40nC)
• High ruggedness
• Fast switching
• 100% avalanche tested
• Improved dv/dt capability
Absolute Maximum Ratings
Symbol
V
DSS
V
GS
I
D
I
DM
E
AS
I
AR
E
AR
dv/dt
P
D
T
J
, T
STG
T
L
Drain-Source Voltage
Gate-Source Voltage
Drain Current
Pulsed Drain Current
T
J
=25℃ unless otherwise specified
TSP7N80M
TSF7N80M
Parameter
Units
V
V
800
± 30
T
C
= 25℃
T
C
= 100℃
(Note 1)
(Note 2)
(Note 1)
(Note 1)
(Note 3)
167
1.33
-55 to +150
300
7.0
4.2
28
7.0*
4.2*
28*
A
A
A
mJ
A
mJ
V/ns
Single Pulsed Avalanche Energy
Avalanche Current
Repetitive Avalanche Energy
Peak Diode Recovery dv/dt
Power Dissipation (T
C
= 25℃)
-Derate above 25℃
680
7.0
16.7
4.5
56
0.44
W
W/℃
℃
℃
Operating and Storage Temperature Range
Maximum lead temperature for soldering purposes,
1/8” from case for 5 seconds
* Drain current limited by maximum junction temperature.
Thermal Resistance Characteristics
Symbol
R
θJC
R
θCS
R
θJA
Parameter
Thermal Resistance,Junction-to-Case
Thermal Resistance,Case-to-Sink Typ.
Thermal Resistance,Junction-to-Ambient
Ver.B1
TSP7N80M
TSF7N80M
Units
℃/W
℃/W
℃/W
0.75
0.5
62.5
2.25
--
62.5
© 2018 Truesemi Semiconductor Corporation
www.truesemi.com
TSP7N80M/TSF7N80M
Electrical Characteristics
T
J
=25
℃
Symbol
Parameter
unless otherwise specified
Test Conditions
Min
Typ
Max
Units
On Characteristics
V
GS
R
DS(ON)
g
FS
BV
DSS
Gate Threshold Voltage
Static Drain-Source
On-Resistance
Forward Transconductance
Drain-Source Breakdown Voltage
V
DS
= V
GS
, I
D
= 250 uA㎂
V
GS
= 10 V, I
D
= 3.5AA
V
DS
=40V,I
D
=3.5A
(Note 4)
3.0
--
--
800
--
--
--
--
--
--
1.4
5.7
--
0.8
--
--
--
--
5.0
V
Ω
S
V
V/℃
uA
uA
nA㎁
nA㎁
1.6
--
--
--
1
10
100
-100
Off Characteristics
V
GS
= 0 V, I
D
= 250 uA㎂
ID = 250 uA, Referenced to 25
℃
V
DS
= 800 V, V
GS
= 0 V
V
DS
=640V, T
J
= 125℃
V
GS
= 30 V, V
DS
= 0 V
V
GS
=- 30 V, V
DS
= 0 V
△BVDSS
Breakdown Voltage Temperature
/
△TJ
Coefficient
I
DSS
I
GSSF
I
GSSR
Zero Gate Voltage Drain Current
Gate-Body Leakage Current,Forward
Gate-Body Leakage Current,Reverse
Dynamic Characteristics
C
iss
C
oss
C
rss
Input Capacitance
Output Capacitance
Reverse Transfer Capacitance
V
DS
= 25 V, V
GS
= 0 V,
f = 1.0 MHz
--
--
--
1685
165
17
--
--
--
pF㎊
pF㎊
pF
Switching Characteristics
t
d(on)
t
r
t
d(off)
t
f
Q
g
Q
gs
Q
gd
Turn-On Time
Turn-On Rise Time
Turn-Off Delay Time
Turn-Off Fall Time
Total Gate Charge
Gate-Source Charge
Gate-Drain Charge
V
DS
= 640 V, I
D
= 7.0A,
V
GS
= 10 V
(Note 4,5)
V
DS
= 400V, I
D
= 7.0A,
R
G
= 25 Ω
(Note 4,5)
--
--
--
--
--
--
--
40
100
50
60
40
9.0
16.5
--
--
--
--
--
--
--
ns
ns㎱
ns㎱
ns㎱
nC
nC
nC
Source-Drain Diode Maximum Ratings and Characteristics
I
S
I
SM
V
SD
t
rr
Q
rr
NOTES:
Continuous Source-Drain Diode Forward Current
Pulsed Source-Drain Diode Forward Current
Source-Drain Diode Forward Voltage
Reverse Recovery Time
Reverse Recovery Charge
I
S
= 7.0 A, V
GS
= 0 V
I
S
=7.0A, V
GS
= 0 V
di
F
/dt = 100 A/μs
(Note 4)
--
--
--
--
--
--
--
--
765
6.8
7.0
28
1.4
--
--
A
V
ns㎱
uC
1. Repetitive Rating: Pulse width limited by maximum junction temperature
2. L=25mH, I
AS
=7.0A, V
DD
=50V, R
G
=25
Ω,
Starting TJ=25
℃
3. I
SD
≤7.0A, di/dt ≤ 200A/us, V
DD
≤ BV
DSS
, Starting TJ = 25
℃
4. Pulse Test: Pulse width ≤ 300us, Duty Cycle ≤ 2%
5. Essentially Independent of Operating Temperature Typical Characteristics
© 2018 Truesemi Semiconductor Corporation
Ver.B1
www.truesemi.com
TI Technology Forum
京公网安备 11010802033920号
EEWORLD
