HR7P195

Parameters

• Kernel

　- High-performance Harvard RISC CPU core

　- 66 simplified instructions

　- Maximum operating frequency is 16MHz

　- 8-level program stack (PC hardware stack)

　- The reset vector is located at 000H, the default interrupt vector is located at 004H, and interrupt priority and interrupt vector table are supported

　- Support interrupt processing, 19 interrupt sources (HR7P195 28pin/32pin supported)

　- Support interrupt processing, 14 interrupt sources (HR7P195 20pin support)

　- Support hardware divider

• Storage resources

　- 4K Words FLASH program memory (supported by HR7P195F8)

　- 8K Words FLASH program memory (supported by HR7P195FG)

　- 512 Bytes SRAM data memory

　- Program memory supports direct addressing

　- Data memory supports direct addressing and indirect addressing

• I/O ports

　- HR7P195 (32pin) supports 29 I/O ports

　- PA port (PA0~PA7)

　- PB port (PB0~PB7)

　- PC port (PC0~PC7)

　- PE port (PE0~PE4)

　- Configurable high current drive ports (supports up to 16 ports)

　- HR7P195 (28pin) supports 25 I/O ports

　- PA port (PA0~PA7)

　- PB port (PB0~PB7)

　- PC port (PC0~PC7)

　- PE port (PE0)

　- Configurable high current drive ports (supports up to 16 ports)

　- HR7P195 (20pin) supports 17 I/O ports

　- PA port (PA0~PA7)

　- PB port (PB0, PB4~PB7)

　- PC port (PC1~PC2, PC6~PC7)

　- Configurable high current drive ports (supports up to 9 ports)

　- Support 1 external port interrupt (PINT0) (HR7P195 20pin support)

　- Support 4 external port interrupts (PINT0~PINT3) (HR7P195 28pin/32pin supported)

　- Supports 1 4-input external key interrupt KINT (KIN0~KIN3 are input terminals)

• Peripherals

　- One 8-bit timer T8N

　- Timer mode (clock source is system clock divided by four (Fosc/4))

　- Counter mode (clock source is T8NCKI)

　- Support configurable prescaler

　- Support interrupt generation

　- Four 8-bit PWM time base timers T8P1/T8P2/T8P3/T8P4

　- Timer mode (clock source is system clock divided by four (Fosc/4))

　- Supports configurable prescaler and postscaler

　- Support interrupt generation

　- Support PWM expansion function (HR7P195 20pin does not support T8P4 PWM expansion function)

　- One 16-bit gated timer T16G

　- Timer mode (clock source is system clock divided by four (Fosc/4))

　- Counter mode (clock source is T16GCKI or LP crystal oscillator)

　- Supports capture mode

　- Support comparator mode

　- Support configurable prescaler

　- Support external gate timing/counting

　- Support interrupt generation

　- Analog-to-digital converter (ADC)

　- Support 10-digit conversion accuracy

　- Support 8-channel analog input (HR7P195 28pin/20pin supported)

　- Support 12-channel analog input (HR7P195 32pin support)

　- Support interrupt generation

　- Support internal ADC RC clock source

　- One high-speed asynchronous receiver and transmitter UART (HR7P195 20pin support)

　- Two-way high-speed asynchronous receiver and transmitter UART (HR7P195 32pin/28pin supported)

　- Support asynchronous full-duplex transmission and reception

　- Support baud rate generator

　- Support 8-bit/9-bit data format

　- Agreement to receive/send from the lowest bit

　- Support interrupt generation

　- Support sending pulse width modulation mode

• special function

　- High-precision internal 16M oscillator

　- Dividable frequency, the lowest frequency can be divided to 125K, can be used as the main system clock source

　- Under 25℃ calibration conditions, the calibration accuracy is ±2%

　- Supports two low power modes: IDLE0 mode and IDLE1 mode, supports wake-up operation

　- Built-in power-on reset circuit

　- Built-in low voltage detection reset circuit

　- Support external reset

　- Support watchdog timer

　- Support prescaler

　- Support internal watchdog RC clock source

　- Support wake-up in IDLE0 mode or IDLE1 mode

　- Support self-programming function

　- Support In-Circuit Programming (ISP) interface

　- Supports In-Circuit Debug (ICD) interface

　- Support programming code encryption protection

• Design and craftsmanship

　- Low power consumption, high speed FLASH CMOS process

　- 20 pins, DIP/SOP/SSOP package

　- 28 pins, SKDIP/SOP package

　- 32 pins, SDIP/SOP package

• Working conditions

　- Operating voltage range: 3.0V ~ 5.5V

　- Operating temperature range: -40 ~ 85℃

Application

White appliances, industrial control and automotive electronics, etc.