HA1-5104-5 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Analog mixed-signal IC> Amplifier circuit> HA1-5104-5

HA1-5104-5: Part NumberHA1-5104-5; CategoryAnalog mixed-signal IC Amplifier circuit; File Size3867.9，13 Pages; ManufacturerHarris; Websitehttp://www.harris.com/

Alternative parts

Part Number	Manufacturer	Description
Sorry, there is no alternative parts yet

HA1-5104-5 Overview

HA1-5104-5 amplifier basic information:

HA1-5104-5 is an OPERATIONAL AMPLIFIER. Commonly used packaging methods are DIP, DIP14,.3

HA1-5104-5 amplifier core information:

The minimum operating temperature of HA1-5104-5 is 75 °C. Maximum bias current at 25°C: 0.2 µA Maximum average bias current is 0.325 µA

How to simply check the efficiency of an amplifier? Looking at its slew rate, the HA1-5104-5 has a nominal slew rate of 3 V/us. The manufacturer specifies a maximum slew rate for the HA1-5104-5 of 6.5 mA and a minimum slew rate of 1 V/us. Its minimum voltage gain is 100000. When the op amp is used in a closed loop, at a specified closed-loop gain (usually 1 or 2, 10, etc.), the frequency when the HA1-5104-5 gain becomes 0.707 times the low-frequency gain is 60000 kHz.

The nominal supply voltage of HA1-5104-5 is 15 V, and its corresponding nominal negative supply voltage is -15 V. The input offset voltage of HA1-5104-5 is 3000 µV (input offset voltage: the compensation voltage required between the two input terminals to make the output terminal of the operational amplifier 0V (or close to 0V).)

Related dimensions of HA1-5104-5:

HA1-5104-5 has 14 terminals. Its terminal position type is: DUAL. Terminal pitch is 2.54 mm.

HA1-5104-5 amplifier additional information:

HA1-5104-5 adopts the VOLTAGE-FEEDBACK architecture. It does not belong to the low offset class of amplifiers. The frequency compensation status of HA1-5104-5 is: YES. Its temperature grade is: COMMERCIAL EXTENDED. HA1-5104-5 is not Rohs certified.

The corresponding JESD-30 code is: R-GDIP-T14. The corresponding JESD-609 code is: e0. The packaging code of HA1-5104-5 is: DIP. The materials used in HA1-5104-5 packaging are mostly CERAMIC and GLASS-SEALED. The package shape is RECTANGULAR.

The form of HA1-5104-5 package pins is: IN-LINE. Its terminal form is: THROUGH-HOLE.

Recommended Resources

Wanbao brand BYD-100H refrigerator circuit

DC inverter circuit diagram

555 simple electrocardiograph checker circuit

T-bridge oscillation circuit

Computer motherboard circuit diagram 440GX_32

Computer motherboard circuit diagram 815 4_54

Source code analysis of Xunwei 4412 development board coprocessor: This article analyzes the uboot source code of 4412 and analyzes what work uboot has done by combining the uboot source code. The source code file analyzed is the "cpu/ ARM_cortexa9 /start.S" file. 1 Source code analysis .globl _start: globl ...; 砂舞的玩笑 Embedded System

[ESK32-360 Review] 4. Run the virtual serial port routine: USB is a complicated and time-consuming thing for me. It mainly describes the device according to the function. For example, USB keyboard, USB virtual serial port, USB camera... And Hetai also added the USB library and made USB a standard library....; ddllxxrr Domestic Chip Exchange

There are three questions about LC series-parallel circuit, transistor static operating point, and 4G 5G diffraction capability.: There are three questions about LC series-parallel circuit, transistor static operating point, and 4G 5G diffraction capability. "LC series-parallel circuit, transistor static operating point, 4G 5G diffraction capability. As shown in the figure" Th...; QWE4562009 Analog electronics

Application solutions and optimization suggestions for low-power Bluetooth ranging technology: With the development of wireless radio frequency technology, short-range wireless communication technologies with significant advantages such as low cost, low energy consumption, low complexity and high sensitivity: RFID, Bluetooth, WiFi, and UWB po...; 疯狂的阿尔夫 RF/Wirelessly

Why does my MSP430F5529 clock initialization use the high-speed XT1 mode, and XT1HFOFFG is always high?: MCU:MSP430F5529 I want to use the XT1 high-speed frequency mode of this microcontroller, but after configuration, the XT1HFOFFG flag is always high. I am now connected to a 12M passive crystal oscillator and two 30PF load capacitors. I made th...; yg776 Microcontroller MCU

Direct imaging digital exposure technology "prints" the innovative future: The printing method known as digital printing has come a long way since it was invented in Germany in the 18th century. Today, digital printing can print text and images on a variety of surfaces, including books and T-shirts. Changes in this pri...; qwqwqw2088 Microcontroller MCU

HA1-5104-5 Also View