EL5486CU datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Analog mixed-signal IC> Amplifier circuit> EL5486CU

EL5486CU: Part NumberEL5486CU; CategoryAnalog mixed-signal IC Amplifier circuit; File Size1522.2，9 Pages; ManufacturerRenesas Electronics Corporation; Websitehttps://www.renesas.com/

Alternative parts

Part Number	Manufacturer	Description
EL5482CU	Rochester Electronics LLC	Basic information of EL5482CU amplifier:EL5482CU is a COMPARATOR. The commonly used packaging method...
EL5482CU-T13	Renesas Electronics Corporation	QUAD COMPARATOR, 4000uV OFFSET-MAX, PDSO24, QSOP-24
EL5486CU-T13	Renesas Electronics Corporation	QUAD COMPARATOR, 4000uV OFFSET-MAX, PDSO24, QSOP-24

EL5486CU Overview

Basic information of EL5486CU amplifier:

EL5486CU is a COMPARATOR. The commonly used packaging method is QSOP-24

EL5486CU amplifier core information:

The minimum operating temperature of the EL5486CU is -40 °C and the maximum operating temperature is 85 °C. Its maximum average bias current is 15 µA

When it comes to an amplifier's sensitivity, nothing is better than its nominal response time. The EL5486CU takes only 4 ns to respond.

The nominal supply voltage of EL5486CU is 5 V, and its corresponding nominal negative supply voltage is -5 V. The input offset voltage of EL5486CU is 4000 µV (input offset voltage: the compensation voltage added between the two input terminals to make the output terminal of the operational amplifier 0V (or close to 0V).)

Related dimensions of EL5486CU:

EL5486CU has 24 terminals. Its terminal position type is: DUAL. Total pins: 24

EL5486CU amplifier additional information:

Its temperature grade is: INDUSTRIAL. EL5486CU is not Rohs certified. The corresponding JESD-30 code is: R-PDSO-G24. The materials used in the EL5486CU package are mostly PLASTIC/EPOXY. The package shape is RECTANGULAR.

The EL5486CU package pin formats are: SMALL OUTLINE. Its terminal forms are: GULL WING.

Recommended Resources

LED lighting display detection circuit with overload protection

Compound excited DC motor forward and reverse circuit

Gas analyzer circuit diagram

C2132.6D horizontal hexagonal automatic lathe electrical schematic circuit 01

Digital bicycle speedometer circuit diagram

555 snoring suppressor circuit

For SMD components with thin pins, what should be the PCB wiring line width?: In the past, I made direct-insert PCBs. I usually set the line width of the power and ground lines to 50 mils, and the other lines to 30 mils. Now I want to make a PCB with both SMD and direct-insert components. For very small SMD chips, how do I ge...; lcwd PCB Design

How to determine the similarity of two signal waveforms: Given two waveforms, i.e. two sets of data, how do we determine the similarity between them? The similarity of two waveforms is the correlation coefficient. 1. Frequency Fourier transform 2. Sliding filter, amplitude characteristics 3. Interconv...; 流萤宸殇 Test/Measurement

SHT31 evaluation + second proofing expansion board: Now it is really convenient and fast to sample PCB boards. I received the modified SHT31 expansion board in just three days. The following is the expansion board after the second sample: This time, the reed for picking up the signal did not u...; hujj Special Edition for Assessment Centres

Will removing the R1 resistor in the anti-reverse connection circuit affect the circuit function?: If we don't need the R1 resistor and directly ground the G pole, will it affect the circuit function? This circuit cannot prevent reverse power connection from damaging output components. The gate resistor is not required. This circuit us...; 普拉卡图 Analog electronics

R4 is clearly 130 ohms, but why is it 412.147M when simulated?: I used multisim to simulate. R4 is 130 ohms, but the simulated value is 412.147M. Is there any way to measure resistance using an ohmmeter? It is common sense that resistance cannot be measured when the circuit is energized (power has been appli...; zlb0183 Analog electronics

EL5486CU Also View