LT1079IS#PBF datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Analog mixed-signal IC> Amplifier circuit> LT1079IS#PBF

LT1079IS#PBF: Part NumberLT1079IS#PBF; CategoryAnalog mixed-signal IC Amplifier circuit; File Size7977.36，18 Pages; ManufacturerLinear ( ADI ); Websitehttp://www.analog.com/cn/index.html; Environmental Compliance

Alternative parts

Part Number	Manufacturer	Description
LT1079IS	Linear Technology	Basic information of LT1079IS amplifier:LT1079IS is an OPERATIONAL AMPLIFIER. Commonly used packagin...
LT1079S	Linear Technology	IC QUAD OP-AMP, 750 uV OFFSET-MAX, 0.2 MHz BAND WIDTH, PDSO16, PLASTIC, SOL-16, Operational Amplifier

LT1079IS#PBF Overview

Basic information of LT1079IS#PBF amplifier:

LT1079IS#PBF is an OPERATIONAL AMPLIFIER. The commonly used packaging method is SOP,

LT1079IS#PBF amplifier core information:

The minimum operating temperature of the LT1079IS#PBF is -40 °C and the maximum operating temperature is 85 °C. Its peak reflow temperature is 250°C and its maximum average bias current is 0.012 µA

How to simply check the efficiency of an amplifier? Looking at its slew rate, the LT1079IS#PBF has a nominal slew rate of 0.1 V/us. When the op amp is used in closed loop, at a certain closed-loop gain (usually 1 or 2, 10, etc.), the frequency when the LT1079IS#PBF gain becomes 0.707 times the low-frequency gain is 200 kHz.

The nominal supply voltage of the LT1079IS#PBF is 15 V, and its corresponding nominal negative supply voltage is -15 V. The input offset voltage of LT1079IS#PBF is 825 µV (Input offset voltage: the compensation voltage added between the two input terminals to make the op amp output terminal 0V (or close to 0V).)

Related dimensions of LT1079IS#PBF:

The width of LT1079IS#PBF is: 3.9 mm and the length is 9.9 mm. LT1079IS#PBF has 16 terminals. Its terminal position type is: DUAL. Terminal pitch is 1.27 mm. Total pins: 16

LT1079IS#PBF amplifier additional information:

Its temperature grade is: INDUSTRIAL. LT1079IS#PBF is not Rohs certified. It does not contain lead. The corresponding JESD-30 code is: R-PDSO-G16. The corresponding JESD-609 code is: e3.

The packaging code of LT1079IS#PBF is: SOP. The materials of LT1079IS#PBF package are mostly PLASTIC/EPOXY. The package shape is RECTANGULAR. The LT1079IS#PBF package pins are: SMALL OUTLINE. Its terminal forms are: GULL WING.

The maximum seat height is 1.752 mm.

Recommended Resources

Switching power supply constant current charger circuit diagram

Application of SHM1120

Peak detector circuit diagram

A Xipu soft starter drives a three-state motor control circuit

Rice cooker circuit drawing 22_Valeo

STK060 power amplifier circuit

[CH579M-R1] + Help: Simulating I2C to read data failed (solved): After successfully driving the LCD5110 display, I started trying to drive the DS1307 calendar module last week. The following picture shows the module purchased from Taobao: This module communicates via the I2C bus. It also comes with a ...; hujj Domestic Chip Exchange

How to use msp430 to output 2-way PWM waveform?: Moreover, the PWM wave frequency can be adjusted step by step by pressing the button, and the PWM wave duty cycle can also be adjusted by pressing the button This is not difficult, just don't ask for too much accuracy. ...; 火辣西米秀 Microcontroller MCU

[Anxinke NB-IoT Development Board EC-01F-Kit] 1. Unboxing: I believe everyone has heard of ESP8266 . I have used Essence ESP 12F and VB series voice modules before. Recently, Essence launched the NBiot module based on cellular network for wide area network: EC01 series module. I applied for it. 1...; xiyue521 RF/Wirelessly

What is the difference between a vector signal source and an RF signal source?: What is the difference between a vector signal source and an RF signal source? What is the difference between a vector signal source and an RF signal source? The following content introduces the introduction and difference between a ve...; len123 Test/Measurement

Has anyone made a circuit that triggers a low level for 2ms and then maintains the low level for 80ms?: Has anyone made a circuit that triggers a low level for 2ms and then maintains the low level for 80ms ? Has anyone made a circuit that triggers a low level for 2ms and then maintains the low level for 80ms? What does 2ms low level trigger mean...; chuzhaonan Analog electronics

Is there a big difference between the calculated linear voltage of the PWM signal through RC filtering and the actual voltage?: Is there a big difference between the calculated linear voltage of the PWM signal through RC filtering and the actual voltage? PWM will have ripples after RC filtering, and the average value is proportional to the duty cycle. What is ? ...; 小太阳yy Switching Power Supply Study Group

LT1079IS#PBF Also View