5962-9312901M2X datasheet, PDF

Datasheet> All Categories > Analog mixed-signal IC> Amplifier circuit> 5962-9312901M2X

5962-9312901M2X: Part Number5962-9312901M2X; CategoryAnalog mixed-signal IC Amplifier circuit; File Size805.1，2 Pages; ManufacturerADI; Websitehttps://www.analog.com

Alternative parts

Part Number	Manufacturer	Description
Sorry, there is no alternative parts yet

5962-9312901M2X Overview

5962-9312901M2X amplifier basic information:

5962-9312901M2X is an OPERATIONAL AMPLIFIER. The commonly used packaging method is LCC-20

5962-9312901M2X amplifier core information:

The minimum operating temperature of the 5962-9312901M2X is -55 °C and the maximum operating temperature is 125 °C. Its peak reflow temperature is NOT SPECIFIED Its maximum average bias current is 9.5 µA

How to simply check the efficiency of an amplifier? Looking at its slew rate, the nominal slew rate of 5962-9312901M2X is 230 V/us. When the op amp is used in closed loop, at a certain closed-loop gain (usually 1 or 2, 10, etc.), the frequency when the 5962-9312901M2X gain becomes 0.707 times the low-frequency gain is 750000 kHz.

The nominal supply voltage of 5962-9312901M2X is 15 V, and its corresponding nominal negative supply voltage is -15 V. The input offset voltage of the 5962-9312901M2X is 500 µV (Input offset voltage: the compensation voltage added between the two input terminals to make the output terminal of the op amp 0V (or close to 0V).)

Related dimensions of 5962-9312901M2X:

The width of 5962-9312901M2X is: 8.89 mm and the length is 8.89 mm. 5962-9312901M2X has 20 terminals. Its terminal position type is: QUAD. Terminal pitch is 1.27 mm. Total pins: 20

5962-9312901M2X amplifier additional information:

Its temperature grade is: MILITARY. The corresponding JESD-30 code is: S-CQCC-N20. The packaging code of 5962-9312901M2X is: QCCN. The materials used in the 5962-9312901M2X package are mostly CERAMIC and METAL-SEALED COFIRED. The package shape is SQUARE.

5962-9312901M2X package pins are: CHIP CARRIER. Its terminal forms are: NO LEAD. The maximum seat height is 2.54 mm.

Recommended Resources

Power supply circuit diagram of CASPER TM-5159 VGA color display

Gantry milling machine beam control circuit

Huabao DYP22A, DYP30A electronic hot water bottle circuit diagram

Double T-shaped RC oscillator circuit diagram

1MHz crystal calibrator

845ddr computer motherboard circuit diagram_48

How to view NPU clock power configuration and information for Allwinner V853 chip?: /arch/arm/boot/dts/sun8iw21p1.dtsi ``` npu: npu@03050000 { compatible = "allwinner,npu"; reg = ; device_type = "npu"; dev_name = " npu"; interrupts = ; clocks = &clk_npu , &clk_pll_npux4 ; clock-frequency = 504000000 ; interrupt-names = "npu"; iommu...; aleksib Domestic Chip Exchange

0R resistors, beads and inductors: 01 0 ohm resistor 0 ohm resistors are often seen in circuit design, and people are often confused: since it is a 0 ohm resistor, it is a wire, why do we need to install it? Are there any such resistors on the marke...; liuhongzhi PCB Design

[BIGTREETECH CB1 core board & PI4B trial] The first unpacking and system installation: Due to the epidemic, the package has not been delivered yet. It is useless to contact customer service. No one is working in the sorting center. After waiting for more than a week, it was finally delivered. 1. Prepare materials: 1.PI4B b...; 常见泽1 Domestic Chip Exchange

About CC2640 power consumption test problem: CC2640 SimpleLink Bluetooth Low Energy Wireless MCU Datasheet (Rev. B) 1. Measurement method: Use DEMO board to measure to eliminate the current difference caused by other peripheral differences. 2. Measurement results: Take the original simpl...; Jacktang Wireless Connectivity

How to choose between embedded and FPGA?: What is the difference between the two? 1. Embedded systems: In the field of electronic information engineering, embedded systems are widely used and are a popular research direction. You can choose to engage in the development of embedded softwar...; huaqingyuanjian FPGA/CPLD

【STM32H7S78-DK】Visual rangefinder based on TouchGFX: 【hardware】 1、STM32H7S78-DK 2. X-NUCLEO-53L4A3 TOF evaluation board 【Software environment】 1、STM32CubeMX6.12 2、X-CUBE-TOF 3、X-CUBE_TOUCHGFX 4、TouchGFX-Designer 5、MDK5.38 【Steps to implement】 1. Use TouchGFX-Designer to generate a ...; lugl4313820 stm32/stm8

5962-9312901M2X Also View