MCP603T-I/CH datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Analog mixed-signal IC> Amplifier circuit> MCP603T-I/CH

MCP603T-I/CH: Part NumberMCP603T-I/CH; CategoryAnalog mixed-signal IC Amplifier circuit; File Size5100.06，29 Pages; ManufacturerMicrochip; Websitehttps://www.microchip.com; Environmental Compliance

Alternative parts

Part Number	Manufacturer	Description
Sorry, there is no alternative parts yet

MCP603T-I/CH Overview

MCP603T-I/CH amplifier basic information:

MCP603T-I/CH is an operational amplifier - Operational Amplifiers (Op Amps - Operational Amplifiers) from Microchip. It belongs to the MCP603 series of products.

MCP603T-I/CH amplifier core information:

The minimum operating temperature of the MCP603T-I/CH is - 40 C and the maximum operating temperature is + 85 C. Output current per channel: 22 mA

The MCP603T-I/CH has a power supply rejection ratio of 80 dB. (Power supply rejection ratio (PSRR): An indicator used to determine the impact of the amplifier output on the power supply. PSRR = 20log[(Ripple(in) / Ripple(out))], that is, the larger the value, the less the amplifier output is affected by the power input. The smaller it is. ) Its voltage gain is 115 dB. The gain bandwidth product (GBP, gain bandwidth product) of the MCP603T-I/CH is 2.8 MHz. As a parameter to simply measure the performance of the amplifier, if you are not only choosing your amplifier, you can use this as a relatively simple measure. index. The corresponding input voltage noise density is 29 nV/sqrt Hz and the corresponding input noise current density is 0.0006 pA/sqrt Hz.

When a voltage difference of 2 mV is applied between the input pins of the MCP603T-I/CH, the output voltage of this amplifier is 0V. (That is, its input bias voltage is 2 mV)

Related dimensions of MCP603T-I/CH:

The width of MCP603T-I/CH is: 1.63 mm, the length is 2.95 mm, and the total number of channels (Number of channels): 1 Channel.

MCP603T-I/CH amplifier additional information:

And its more detailed single package form is: SOT-23-6. When suppliers on the market sell MCP603T-I/CH, they use the form: Reel.

Recommended Resources

Wiring a when the leakage protector in the TN system supplies a three-phase balanced load

Quartz temperature sensor circuit diagram

Gongtai GT-JDG2 through-core protection circuit

Transformer coupled amplifier circuit for sensors

Large dynamic range voltage-controlled gain amplifier circuit

Software defines IoT chips, and technology integration promotes LPWAN2.0 ubiquitous IoT (Part 1): As one of the important infrastructures of the digital industry, the Internet of Things has ushered in a golden period of development. Through the collection, analysis and output of data, the Internet of Things communication technology has deepened ...; zeta联盟 RF/Wirelessly

[TI recommended course] #Live replay: 3 hours of practice + analysis: TI engineers take you step by step to fully get started with MSP430#: //training.eeworld.com.cn/TI/show/course/5679 This is how I got started. I'm using MSP430F149 now, which is a bit old and I haven't upgraded it to other models because the quantity is small. MSP430 has good performance and low power consumption. ...; Hk2020 TI Technology Forum

Ultrasonic transducer / piezoelectric ceramic transducer driving problem series 1: Ultrasonic transducer/piezoelectric ceramic transducer drive problem series 1 "Design and implementation of portable ultrasonic therapy device based on frequency tracking" The company file is encrypted, so it is not uploaded. It can be searched w...; QWE4562009 Circuit Observation Room

EK140 Burning Guide: MY-IMX6 MfgTool-v2.6 User Guide 目录隐藏 ] 1准备烧录工具 1.1下载烧录工具 1.2配置烧录工具 2为开发板烧录系统 2.1使开发板处于下载模式 2.2连接开发板和电脑 2.3烧录系统到开发板 2.4烧录出错处理 2.5启动开发板 3烧录工具的生产化使用 3.1配置烧录工具同时烧录多个设备 3.2烧录自己编译的Image 3.3烧录自己的应用程...; 明远智睿Lan ARM Technology

In a DCDC circuit, when calculating the switching loss of MOS, how should the rise and fall times be calculated?: In a DCDC circuit, when calculating the switching loss of MOS, how should the rise and fall times be calculated? The following is the estimated formula for the switching loss of the DCDC switch MOS given in the book. How do I calculate the ts...; 小太阳yy Switching Power Supply Study Group

How much impact does straightening the routing have on EMC?: This can only be measured, but this right angle is definitely not good. Is the via considered a right angle? Is the board above Rogers board? The reason why you can't go at right angles is for high-frequency signals. If you control the signa...; btty038 PCB Design

MCP603T-I/CH Also View