datasheet, PDF - EEWORLD Datasheet

: Part Number; Manufacturer

Download Datasheet

Alternative parts

Part Number	Manufacturer	Description
Sorry, there is no alternative parts yet

Overview

LTC6269HMS8E#PBF amplifier basic information:

LTC6269HMS8E#PBF is an operational amplifier - Operational Amplifiers (Op Amps - Operational Amplifiers) from Analog Devices Inc. It belongs to the LTC6269 series of products.

LTC6269HMS8E#PBF amplifier core information:

The minimum operating temperature of the LTC6269HMS8E#PBF is -40 C and the maximum operating temperature is +125 C. The corresponding working power supply current is 16.5 mA. The output current of each channel is: 90 mA.

The LTC6269HMS8E#PBF has a power supply rejection ratio of 95 dB. (Power supply rejection ratio (PSRR): An indicator used to determine the impact of the amplifier output on the power supply. PSRR = 20log[(Ripple(in) / Ripple(out))], that is, the larger the value, the less the amplifier output is affected by the power input. The smaller.) The amplifier gain of LTC6269HMS8E#PBF can reach: 250 V/mV (The amplifier gain is the logarithm of the ratio of the amplifier output power to the input power, which is used to indicate the degree of power amplification. It also refers to the amplification factor of voltage or current. Similarly , decibel is the unit of amplifier gain.) The gain bandwidth product (GBP, gain bandwidth product) of LTC6269HMS8E#PBF is 500 MHz. As a parameter to simply measure the performance of the amplifier, if you are not sure how to choose your amplifier, you can This is a relatively simple measurement indicator. The corresponding input voltage noise density is 4.3 nV/rtHz and the corresponding input noise current density is 0.0055 pA/rtHz

When a voltage difference of 0.2 mV is input between the LTC6269HMS8E#PBF input pins, the output voltage of this amplifier is 0V. (That is, its input bias voltage is 0.2 mV)

Related dimensions of LTC6269HMS8E#PBF:

Number of channels in total: 2 Channels.

LTC6269HMS8E#PBF amplifier additional information:

And its more detailed single package form is: MSOP-8. When suppliers on the market sell LTC6269HMS8E#PBF, they use the form: Tube.

Recommended Resources

Coordinating wiring between leakage protector and fuse, isolating switch and circuit breakerb

Kangwu brand BD-120 refrigerator circuit

Electric bicycle Jiateng charger circuit diagram

Jinling brand APT20-3-1, APT25-4-1, APT30-5-1 ceiling ventilation fan circuit diagram

Application of IR2110 in Buck converter

Functional block diagram and application of X9241

[AT-START-F403A Review] Part 2: Environment setup is very simple: 1. Introduction After a long time, I finally had time to do the review on the weekend. I have always wanted to write a review, but my partner always asked me to accompany her, so I secretly wrote the review when my partner was resting. It took ten...; w494143467 Domestic Chip Exchange

PID regulation problem: I bought a development board, F407, which has a routine for PID regulation. For example, to adjust the speed of a DC motor, by adjusting the PID parameters, the duty cycle of the PWM wave is reduced when the speed is high. When the speed is lo...; chenbingjy stm32/stm8

NUCLEO's ST-LINK is changed to 1.8V and the computer cannot recognize the hardware: I want to debug the LIS25BA sensor. I don't have a level conversion chip, so I want to change the NUCLEO to 1.8V power supply. For debugging convenience, I first changed the 3.3V LDO of ST-LINK to 1.8V, and then plugged it into the computer and it...; littleshrimp stm32/stm8

HPM6000 Series Microcontroller CMSIS DAP Debugger User Guide: This article was tested and written by Professor Fei Zhendong, senior engineer of Shanghai Pioneer Semiconductor . Most of the HPM series MCU evaluation kits provided by Shanghai Xianji are equipped with an onboard debugger based on FTDI's FT2...; 谍纸天眼 Domestic Chip Exchange

I decided to quit my job and develop my operating system full-time (transferred): Reprinted from: https://zhuanlan.zhihu.com/p/407878981 Today I read a story about a Swedish programmer who, in just six months of his spare time, single-handedly built something that would take an average programmer several years or even more th...; freebsder Embedded System

Standards and control circuits for electric vehicle charging interfaces: The reference standard parts of China's electric vehicle standard charging interface and handshake circuit are GB/T 20234 and GB/T 18487.1 respectively. The maximum voltage of the AC charging interface is three-phase 440V AC, and t...; 火辣西米秀 Automotive Electronics

Also View