SP3-2500-2 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Analog mixed-signal IC> Amplifier circuit> SP3-2500-2

SP3-2500-2: Part NumberSP3-2500-2; CategoryAnalog mixed-signal IC Amplifier circuit; File Size1941.86，6 Pages; ManufacturerSIPEX; Websitehttp://www.sipex.com/

Alternative parts

Part Number	Manufacturer	Description
SP2-2500-5	Sipex Corporation	Operational Amplifier, 1 Func, 5000uV Offset-Max, MBCY8, METAL CAN-8
SP7-2500-5	Sipex Corporation	Operational Amplifier, 1 Func, 5000uV Offset-Max, CDIP8, MINI, CERDIP-8
SP2-2500-4	Sipex Corporation	Operational Amplifier, 1 Func, 5000uV Offset-Max, MBCY8, METAL CAN-8
SP3-2500/883	Sipex Corporation	SP3-2500/883 amplifier basic information:SP3-2500/883 is an OPERATIONAL AMPLIFIER. Commonly used pac...
SP7-2500-4	Sipex Corporation	Operational Amplifier, 1 Func, 5000uV Offset-Max, CDIP8, MINI, CERDIP-8

SP3-2500-2 Overview

SP3-2500-2 amplifier basic information:

SP3-2500-2 is an OPERATIONAL AMPLIFIER. Commonly used packaging methods are PLASTIC, DIP-8

SP3-2500-2 amplifier core information:

The minimum operating temperature of the SP3-2500-2 is -55 °C and the maximum operating temperature is 125 °C. Its maximum average bias current is 0.2 µA

How to simply check the efficiency of an amplifier? Looking at its slew rate, the SP3-2500-2 has a nominal slew rate of 30 V/us. The manufacturer specifies a maximum slew rate for the SP3-2500-2 of 6 mA and a minimum slew rate of 25 V/us. Its minimum voltage gain is 20000. When the op amp is used in closed loop, at a certain closed-loop gain (usually 1 or 2, 10, etc.), the frequency when the SP3-2500-2 gain becomes 0.707 times the low-frequency gain is 12000 kHz.

The nominal supply voltage of the SP3-2500-2 is 15 V, and its corresponding nominal negative supply voltage is -15 V. The input offset voltage of SP3-2500-2 is 5000 µV (input offset voltage: the compensation voltage added between the two input terminals to make the output terminal of the operational amplifier 0V (or close to 0V).)

Related dimensions of SP3-2500-2:

The width of SP3-2500-2 is: 7.62 mm and the length is 11.176 mm. SP3-2500-2 has 8 terminals. Its terminal position type is: DUAL. Terminal pitch is 2.54 mm.

SP3-2500-2 amplifier additional information:

Its temperature grade is: MILITARY. The corresponding JESD-30 code is: R-PDIP-T8. The packaging code of SP3-2500-2 is: DIP. The materials used in SP3-2500-2 packaging are mostly PLASTIC/EPOXY. The package shape is RECTANGULAR.

The form of SP3-2500-2 package pins is: IN-LINE. Its terminal form is: THROUGH-HOLE.

Recommended Resources

Magnetic Wedding Doll Circuit

Soil moisture upper and lower limit alarm

800W triac dimming circuit

QJB gas monitoring alarm circuit

TDA8185 power amplifier circuit

Self-excited switching integrated regulated power supply

Introduction to the estimation method of the remaining capacity SOC of lithium batteries: The state of charge, also known as the remaining power, SOC, is a parameter that reflects the percentage of the current power in the battery pack to the total available capacity. Electric vehicle drivers can infer the current battery life based ...; qwqwqw2088 Analogue and Mixed Signal

Respond to positive feedback with more options: “Unleashing flexibility in power design: Introducing UnitedSiC’s fourth generation SiC FETs with expanded options” Respond to positive feedback with more options When does negative feedback become positive feedback? When the control engineer wan...; btty038 RF/Wirelessly

Reading Notes on "Embracing AIGC" (1): I just received the book yesterday. I was busy with work and had a long time off from the forum. I thought I had missed the time to get the book, but the eeworld lady found me in the WeChat group . Since I can still participate in the event, I can't...; anning865 Embedded System

The modelsim simulation of the shift-add multiplier written in vhdl does not meet expectations: The modelsim simulation of the shift-add multiplier written in vhdl does not meet expectations. I can't find the problem myself, and hope to get your advice Original code LIBRARY IEEE; USE IEEE.STD_LOGIC_1164.ALL; USE IEEE.STD_LOGIC_UNSIGNED.A...; 洽洽香瓜子 FPGA/CPLD

How to use JTAG to program UCD90120A: I saw that the information on the official website is all configured using PMBUS, but since our project uses the JTAG interface, I would like to ask colleagues who have used JTAG burning to share their experience in JTAG burning. Thank you so much...; dreamorwph Power technology

【Follow me Season 2 Episode 2】--Task Summary: ## Thank you for the forum. Through this event, I have a deep and comprehensive understanding of the use of Arduino UNO R4 WiFi, which lays the foundation for subsequent development. ## My task summary### Part 1: Demonstration video The videos of al...; upc_arm DigiKey Technology Zone

SP3-2500-2 Also View