【MSPM0L1306 LaunchPad Development Kit Review】2 Development Tool Installation and Configuration

北方

【MSPM0L1306 LaunchPad Development Kit Review】2 Development Tool Installation and Configuration [Copy link]

 

1 Installation Tools

The MSPM0L1306 LaunchPad development kit has a variety of software development tools available, such as TI's Code Composer Studio IDE, IAR Embedded Workbench IDE and Keil Vision IDE. Among these installed IDEs, TI's original development tool CCS is the most common, which can be used with various XDS series. There is also a sysconfig, which is a system configuration tool and a very convenient development tool.

The various resources of the development board hardware used are clearly shown in the figure below.

The corresponding text version of the connection diagram is as follows. The dotted line is the XDS110 debugger, and the dotted line is the onboard LED and other resources.

2 Sysconfig configuration process

Start the installation

After the installation is complete, it will start smoothly. To start, you need to select the product and SDK first.

This will start the program installation successfully.

3 TI CCS installation and configuration process

Start the installer,

Then select the hardware driver you need to install, here select MSPM0 and MSP430

Specifically indicates unsupported debuggers,

start installation,

After the installation is complete, you need to restart the system for the configuration to take effect.

Then start the program and install it successfully

This way CCS is also installed successfully

4 Built-in program operation and experience

This development board is equipped with a factory program to control the following hardware resources

• LED Light

The specific connection pins and LED correspondence are as follows

• Light sensor

The connection of the light sensor is as follows,

• Thermistor

A 10k linear thermistor (PTC) – TMP6131 is included, the PTC is in a low side configuration with a 10kΩ 10ppm pull-up resistor. The default position of the jumper in the header shown (1-2 position) connects the circuit directly to the ADC. In this mode, the output voltage is approximately 1.6V at room temperature. The jumper can also be set to the 2-3 position to allow the OPA to be connected to the thermistor. The OPA output can be internally connected to the negative OPA terminal using software. This allows the OPA to be used as a buffer for the thermistor and internally connected to the ADC channel for sampling.

Connect the USB lead, and then connect the tool putty through the serial port. This will continuously display the status of the above three external devices, and use the two onboard buttons to switch and control them. The screenshot is as follows.

5 Others

Another development tool is cloud development, which does not require the installation of IDE, and can be debugged and developed directly online. Here, the TI agent plug-in needs to be installed, and the installation process does not seem to be very smooth. Therefore, for cloud development, the local firewall and antivirus software should not be too aggressive, and should have a tolerance for pop-ups. Try to install and use this later.

lugl4313820

I tried it and found that keil+sysconfig is more convenient to use. I used ccs before, but the installation package was too large.

北方

lugl4313820 posted on 2023-10-7 11:19 I tried it and found that keil+sysconfig is more convenient to use. I used ccs before, but the installation package is too large.

CCS now does not need to choose so many SDKs, it is still acceptable to only choose MSP

lugl4313820

Northern published on 2023-10-7 12:19 CCS now does not need to choose so many SDKs, it is still acceptable to choose only MSP

However, if you want to be lightweight, VSCODE+GCC is more convenient, but debugging is a little troublesome.

秦天qintian0303

lugl4313820 posted on 2023-10-7 13:07 However, if you want to be lightweight, VSCODE+GCC is more convenient. It's just that debugging is a little troublesome.

It is necessary to create a development environment that supports online debugging

lugl4313820

Qintianqintian0303 posted on 2023-10-7 17:29 It is necessary to create a development environment that supports online debugging

vscode also has online debugging tools, but they are not as intuitive as the classic IDE.