5611 views|9 replies

3

Posts

0

Resources
The OP
 

Please recommend a microcontroller with 5V IO port output [Copy link]

 
I need to use 5V output as a trigger signal, but I don't know which microcontroller's IO port output is 5V. Can you recommend one? Thank you.
This post is from 51mcu

Latest reply

This post was last edited by LuJianchang on 2018-11-21 09:45 1. Some IOs of stm32 are tolerant to 5V. Set open-drain output, and then add a 5V pull-up resistor; 2. Use two NPN transistors for switch control. If the output waveform does not require the same phase, one transistor can be omitted. Attach the circuit simulation diagram. [attach]388266[/attach]   Details Published on 2018-11-21 09:09
 

9717

Posts

24

Resources
2
 
Nowadays, microcontrollers are moving towards low voltage. I suggest you use level conversion. I have played with Fuji's cortex-m3 microcontroller before. It supports 5v operation and generates a lot of heat. You can take a look at this series MB9BF524LPMC1
This post is from 51mcu
 
 
 

2w

Posts

0

Resources
3
 
For a microcontroller with a working power supply voltage of 5V, the output amplitude can generally reach 0~5V. For an old microcontroller, the working power supply voltage is generally 5V.
This post is from 51mcu
 
 
 

3

Posts

0

Resources
4
 
littleshrimp posted on 2018-11-19 13:43 Nowadays, microcontrollers are moving towards low voltage. I suggest you use level conversion. I used to play with Fuji's cortex-m3 microcontroller that supports 5V. It generates serious heat when working...
Thank you. I plan to use a 3.3V microcontroller with level conversion.
This post is from 51mcu
 
 
 

3

Posts

0

Resources
5
 
maychang posted on 2018-11-19 13:48 The output amplitude of a microcontroller with a working power supply voltage of 5V can generally reach 0~5V. For old microcontrollers, the working power supply voltage is generally 5V.
Thank you, STC89C52 has a 5V microcontroller, but I plan to use a 3.3V microcontroller with a level converter.
This post is from 51mcu

Comments

In fact, this is the best way.  Details Published on 2018-11-19 14:07
 
 
 

2w

Posts

0

Resources
6
 
hugue posted on 2018-11-19 14:02 Thank you, STC89C52 has a 5V microcontroller, but I plan to use a 3.3V microcontroller with level conversion.
In fact, this is the best way.
This post is from 51mcu
 
 
 

2113

Posts

0

Resources
7
 
Why do you need a 5V microcontroller? Just use 164245 or 16245 to convert it. If you want to select bidirectionally, use TXB0104. In addition, 5V voltage is not your only standard. For example, capacity, speed, etc. So use the more popular ones in the industry and convert them.
This post is from 51mcu
 
 
 

1w

Posts

25

Resources
8
 
Many AVR, PIC, and 51 support 5V.
This post is from 51mcu
 
 
 

1w

Posts

142

Resources
9
 
Except for antiques from the 1980s or earlier, any 5V powered MCU has IO outputs very close to 5V, and any MCU powered below 5V cannot directly output 5V. So, you either use 5V to directly power the MCU, or add an external level converter, but it still requires a 5V power supply.
This post is from 51mcu
 
Personal signature上传了一些书籍资料,也许有你想要的:https://download.eeworld.com.cn/user/chunyang
 
 

216

Posts

0

Resources
10
 
This post was last edited by LuJianchang on 2018-11-21 09:45 1. Some IOs of stm32 are tolerant to 5V. Set open-drain output, and then add a 5V pull-up resistor; 2. Use two NPN transistors for switch control. If the output waveform does not require the same phase, one transistor can be omitted. Attach the circuit simulation diagram.
This post is from 51mcu
 
 
 

Guess Your Favourite
Just looking around
Find a datasheet?

EEWorld Datasheet Technical Support

Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号
快速回复 返回顶部 Return list