Design and implementation of a simple logic analyzer based on FPGA

Recommended ContentMore

Open source project More

• expansion dock
• KEA128-3-Phase Sensorless BLDC Reference Design
• SECO-LVDCDC3064-IGBT-GEVB: 6 - 18 Vdc input isolated IGBT gate driver supply +15 V / -7.5 V / 7.5 V with automotive grade NCV3064 controller
• [Internet of Things] WiFi smart switch +4212724A
• MC68HC908JW32 Evaluation Kit Hardware/Software Example
• For smart devices, SABER board based on i.MX 6SoloX application processor
• stc8a8k minimal system board
• VN5E050J Evaluation Board
• 3-phase AC 400V input PFC converter
• 42 stepper motor closed loop solution

Searched by Users

• Based on single chip microcomputer, 74HC595 drives two stepper motors through ULN2003
• The program for receiving infrared by stm32 uses hx1838 chip
• Download the Chemical and Chemical Engineering Dictionary
• Commonly used encapsulation libraries for AD software
• GB 26788-2011 General safety specification for elastic pressure instruments.pdf
• USB-TTL-STC MCU Downloader PCB Layout Sharing.rar
• MPLAB IDE Integrated Development Environment V6.3 Download
• STM32F407 drives EC20 module MCU source code, for your reference
• Technical specification for relay protection and safety automatic devices GB/T 14285—200X
• AH6956 Application Note

Just Take a LookMore

• DSP interrupt path flow chart
  Any peripheral or external interrupt that contains the PIE interrupt source, and its own peripheral interrupt module can also be enabled.PIE recognizes INTx.y, and the bit of PIE interrupt is Latched,
• Detailed explanation of terminal device state switching in TI ZigBee protocol stack
  This article mainly introduces the detailed description of the switching between different states during the operation of the terminal device End Device in TI ZigBee protocol stack Z-Stack, and furthe
• Understand low-pass, high-pass, band-pass, band-stop, and state-adjustable filters at once!
  The second-order voltage-controlled low-pass filter circuit is shown in the figure. R1, C1 and R2, C2 respectively form two first-order low-pass filters, but C1 is connected to the output end to intro
• An error occurred when updating the PCB. Please help me find out why.
  An error occurred when updating the PCB. Please help me find out why. Net s13 exists and is connected to the electrical contacts of the pins. There is no error. Why is the error reported?
• [Free trial of Pingtouge Bluetooth Mesh Gateway Development Kit] + Gateway module to cloud platform and problem solving
  [i=s]This post was last edited by damiaa on 2021-11-20 10:07[/i][Free trial of Pingtouge Bluetooth Mesh Gateway Development Kit] + Gateway module to cloud platform and problem solving According to the
• 【Smart Kitchen】Environmental Sensor Schematic Design
• bq34110 cannot program parameters
• Bicycle modification series——by dcexpert
• Question: Which channel do you use to purchase components for your company's products?
• New opportunity to counterattack! Come to EEWorld Download Center, complete tasks to earn 200 points, and easily achieve point freedom

Trending Downloads

• Dimmable LED driver iW3612 (EBC898-A)
• MAX1284E
• Schematic diagram of DC-AC converter composed of 555 circuit
• LPC1752 Registers
• Allegro Chinese Learning Tutorial.pdf
• Establishment of ultrafiltration separation model of Agaricus blazei polysaccharide based on BP neural network
• Embedded real-time operating system MicroCOS_II CD content.rar
• ANX9030 datasheet,pdf, HDMI Transmitter
• Analysis of the classic LLC principle---sharing
• Baoding Aozhuo-AZ-WXZ microcomputer detuning device

Trending ArticlesMore

• Microchip Development Tools Spring Sale!
• Cypress Partners with Semtech to Provide LoRaWAN™ Integrated Solutions for Smart City Applications
• Zhongke Galaxy Core: Enabling the localization of high-performance sensor chips
• Korean media: Why Samsung's Exynos chips are not sold to the public? It turns out that Qualcomm is behind it
• How to extend the battery life by 1.3 times?
• R7F0C002 Smart water cup
• Accurate and stable, how would you rate this combination?
• Before designing a switching power supply, you must do analysis, simulation, and experiments (Part 3)
• Want to be a big shot in the industry? Come on, let’s set a small goal first