Training
Profile
The Digital Power Starter Kit (Product Number: DM330017) is based on the dsPIC33FJ09GS302 low-cost 16-bit digital signal controller, allowing users to easily explore and evaluate the dsPIC33F "GS" digital power conversion series. The starter kit is a digitally controlled power board that includes an independent DC/DC synchronous buck converter and an independent DC/DC boost converter, as well as an LCD display, potentiometer, temperature sensor, programmable Onboard in-circuit debugger/programmer for resistive loads and USB interface.
You Might Like
Recommended Posts
- What do LPC3600 and LCC3600 corresponding to bit 0 and bit 4 in the LCD control register TCONSEL of S3C2440A refer to?
- For these two bits, some codes modify its value, I am not sure how to modify it. I checked it on the Internet, some people said it is related to the "LCD companion IC", some people said it is related
-
ysbqw
Embedded System
- Section Navigation
- Personally, I feel that there are too many things in the forum, and I don't know where to start. I was blind for a while. Many times, the more the better. In the end, I didn't learn anything thoroughl
-
gaoxiao
Microcontroller MCU
- New version of the forum home page Tucao place
- [p=30, null, left][font=微软雅黑, Arial, Helvetica, sans-serif][size=3]Hi, everyone! [/size][/font][/p][p=30, null, left][font=微软雅黑, Arial, Helvetica, sans-serif][size=3] The new version of the forum home
-
eric_wang
Talking
- What task status does PEND+T indicate?
- In the shell, the task status is sometimes displayed as PEND, and sometimes as PEND+T. What does the "T" mean?
-
ponny7
Embedded System
- Verilog_golden Golden Manual Chinese version Zhou Ligong.pdf
- Verilog_golden Golden Manual Chinese Edition Zhou Ligong
-
493025560
FPGA/CPLD
- Last day for pre-registration! In-depth analysis of Infineon's star product IGBT7, live broadcast to understand the device operation and load process
- "How to Design High-Performance Servo Drive Using Infineon IGBT7" invites you to participate ~reduce costs and increase efficiency, focus on the new production process of industrial semiconductors, an
-
dancerzj
Power technology
Recommended Content
Web users are watching Change
- What do LPC3600 and LCC3600 corresponding to bit 0 and bit 4 in the LCD control register TCONSEL of S3C2440A refer to?
- Section Navigation
- New version of the forum home page Tucao place
- What task status does PEND+T indicate?
- Verilog_golden Golden Manual Chinese version Zhou Ligong.pdf
- Last day for pre-registration! In-depth analysis of Infineon's star product IGBT7, live broadcast to understand the device operation and load process
- Comparison of Two Control Methods and Zero-Crossing Output Characteristics of Unipolar SPWM
- [Rawpixel RVB2601 development board trial experience] Use FreeRTOS with caution
- About the Bluetooth address of 2541
- CIRCUIT PLAYGROUND EXPRESS with MakeCode and CircuitPython support
- ST's new STM32WB wireless chip will integrate Bluetooth 5+IEE802.15.4 (OPENTHREAD+ZIGBEE). Are you looking forward to it? !!!
- uart2
- Fujitsu FRAM Experience Submission
- wang1jin takes you to learn PCB design from scratch 8 hours video tutorial download address
- CC4001 Quad 2-input NOR gate
- Can VIVI be used to transplant bootloader using Skyeye simulated kernel?
- Analysis of the top ten popular RF and microwave devices
- Are there any other embedded office software for mobile phones besides QuickOffice?
- Common sensor information
- Regarding the USB enumeration problem developed in ThreadX system, waiting for expert guidance
- About the program of fpga controlling peripherals through cpld
- Questions about the hardware design of STM32F207+DP83848. Why is the hardware design like this in RMII mode connection?
- DIY online design steps
- AVR serial port receives interrupt word
- Also on the anti-interference performance of PIC and AVR
- 1ppm DAC, how do you usually achieve it?
- Launchpad price increased to $9.99
- About Atmel SAM D21 Xplained Pro Evaluation Kit
- The following error occurred when compiling linphone. I don't know how to fix it. I hope to get some advice from an expert. Thank you
- Will connecting multiple power supplies in parallel affect the LED?
Popular Components
Just Take a Look
Hot Downloads
- LM341/LM78M50,pdf datasheet (3-Terminal Positive Voltage Regulators)
- Introduction to Spreadtrum Platform Software Architecture (GSM Solution)
- cc2530 package library
- Shorten the cycle time of 8-pin ADS78xx series
- National Undergraduate Electronic Design Competition Topic: Liquid Drip Control Program
- RDA RDA5800 Spec
- Selection of rectifier filter capacitors
- Working principle and application of live working insulation rod tester
- \"The world is flat\"
- Design of temperature detection and heat dissipation protection circuit for microprocessor chip
MoreHot Articles
京公网安备 11010802033920号