Training
Profile
Introduces the basic concepts of heterogeneous computing, the basic development methods of OpenCL and the implementation of artificial intelligence applications.
Chapters
Chapter 1：Introduction to Heterogeneous Computing and OpenCL (13 minutes and 29 seconds)
Chapter 2：OpenCL programming based on (20 minutes and 14 seconds)
Chapter 3：OpenCL programming basics (12 minutes and 41 seconds)
Chapter 4：Introduction to OpenCL development environment (13 minutes and 41 seconds)
Chapter 5：FPGA development process demonstration based on OpenCL (28 minutes and 43 seconds)
Chapter 6：Simple neural network implementation based on OpenCL (17 minutes and 42 seconds)
You Might Like
Recommended Posts
- Power problem help
- Use a switching power supply to convert 220V to 12V, then use 7805 to convert the 12V of the switching power supply to 5V directly for the microcontroller, and 7806 to convert it to 6V for the servo.
-
一瓶矿泉水
Power technology
- Let's discuss again why STM32 always burns out inexplicably
- [i=s]This post was last edited by jishuaihu on 2015-6-1 09:47[/i] As a classic and cheap ARM chip, STM32 has been favored by many engineers and is also quite common in practical applications. However,
-
jishuaihu
stm32/stm8
- Questions about cdma modem
- There is a device with wince5.0 and Huawei em200 cdma module. I use ras to connect to the network and then disconnect to make a call, but after disconnecting, the serial port still sends out messy gar
-
lock
Embedded System
- TQ6410 simulation has problems, please help
- I recently wanted to do some bare metal programming on ARM 11. I used the TQ6410 development board, the Jlinkv8 simulator , and the simulator interface conversion board that comes with the TQ6410. The
-
wenbodong
ARM Technology
- Moderator Chip Coin Rewards in July 2011!
- Moderator chip currency issuance requirements: Monthly online time> 30 hours Monthly posts> 30 posts Some small rules for moderators: [url=https://en.eeworld.com/bbs/thread-77551-1-1.html]https://bbs.
-
EEWORLD社区
Suggestions & Announcements
- Is Ka3525 a voltage type or current type pulse width modulation?
- I would like to ask, is Ka3525 a voltage-type or current-type pulse width modulation? Why does the manual say it is a VOLTAGE-MODE PWM CONTROLLER, but in fact the Chinese content online all talks abou
-
sunboy25
Power technology
Recommended Content
Web users are watching Change
- Power problem help
- Let's discuss again why STM32 always burns out inexplicably
- Questions about cdma modem
- TQ6410 simulation has problems, please help
- Moderator Chip Coin Rewards in July 2011!
- Is Ka3525 a voltage type or current type pulse width modulation?
- Did your mother lie to you when you were a child?
- Has anyone seen these Fairchild ICs?
- (Video) C64x+ Network Course (IV) - C Code Optimization
- Wireless water and electricity remote meter reading system solution
- Toshiba Bazooka Dual Window
- R&D investment of my country's top 100 electronic information companies
- Some Problems in Automobile CAN Communication
- Ultra-low power consumption process design segment LCD liquid crystal display driver IC
- Several basic concepts of DSP software and hardware
- Is there anyone using PXA270 to run WINCE?
- What does LEQ and ECO mean in astro?
- New York Times: A day in the life of Microsoft CEO Ballmer (Photo)
- How to increase the speed of my computer? When I right-click my computer, the dialog box pops up very slowly. What's going on? How can I increase the speed?
- Embedded Learning and Technology Development Staff Track
- I am developing a system in C# under WinCE and want to draw buttons myself. Has anyone done this before? Thank you.
- Questions about STM32_407 input capture pulse counting
- Problems with constant current source composed of op amp + MOS tube
- EEWORLD University ---- Power Design Tips 41: DDR Memory Power Supply
- [Share your experience] Initial application after receiving MSP-SA430-SUB1GHZ
- Problems in implementing LIN communication via UART
- Regarding the use of voltage regulator tube and TVS tube, please help me!!!
- ARM for Beginners
- DSP interface
- It turns out that you need to unplug the jtag
Popular Components
Just Take a Look
Hot Downloads
- Requirements for driver IC selection for the new generation of offline LED lamps
- Cool simulator homemade data
- Implementation of audio directional algorithm based on ADSP-BF533
- Link2.c C program source code
- -Production process of linear high voltage regulator.pdf
- Introduction to CMOS Circuit
- Development Board MSP430F149
- Experimental study on the electric field effect of DC and AC superposition electric fields
- CD4029B,pdf(TYPES)
- FPGA Simple Design Principles and Applications (Ming Deyang)
MoreHot Articles
- Analysis of white LED backlight dimming solution
- Mouser Now Stocking Qorvo QPQ1298 High-Performance BAW Filter
- Groundbreaking Bayesian Deep Learning Enables Energy-Efficient AI
- Ask the court to declare that its 5G patent licensing rates comply with the FRAND principle
- STM32 collects signals from DHT11 temperature and humidity sensor
- How to operate an infrared spectrophotometer?
- STM8L151C8 MCU learning routine (13) - DHT11
- Details determine success or failure--Three key points in the design of the power supply system of the electronic blood pressure monitor
- Huawei's fourth major event: seven years of planning and three years of invisibility, what are the chances of success or failure?
- Qualcomm presents industry-leading AI innovations and collaborations at CES 2025, covering PCs, cars, smart homes and enterprise
京公网安备 11010802033920号