Training
Profile
IOT-ARM architecture and programming video tutorial
Chapters
Chapter 1：ARM world (11 minutes and 11 seconds)
Chapter 2：Development environment setup 1 (20 minutes and 12 seconds)
Chapter 3：Development environment setup 2 (12 minutes and 20 seconds)
Chapter 4：Supplementary Linux installation Sourceinsight (4 minutes and 57 seconds)
Chapter 5：Supplementary MiniTool programming development board-11.30 update tool (16 minutes and 30 seconds)
Chapter 6：ARM Architecture-Learning Method (20 minutes and 33 seconds)
Chapter 7：ARM Architecture-Processor and Noun 1 (17 minutes and 48 seconds)
Chapter 8：ARM Architecture-Processor and Noun 2 (18 minutes and 2 seconds)
Chapter 9：ARM Architecture - Tools and Cross-Toolchains (16 minutes and 7 seconds)
Chapter 10：Processor modes and on-chip registers 1 (20 minutes and 7 seconds)
Chapter 11：ARM exceptions and interrupts 2 (20 minutes and 5 seconds)
Chapter 12：Processor modes and on-chip registers 3 (20 minutes and 11 seconds)
Chapter 13：Processor modes and on-chip registers 4 (10 minutes and 42 seconds)
Chapter 14：ARM assembly addressing mode 1 (20 minutes and 5 seconds)
Chapter 15：ARM assembly addressing mode 2 (20 minutes and 12 seconds)
Chapter 16：ARM assembly addressing mode 3 (17 minutes and 38 seconds)
Chapter 17：ARM assembly arithmetic operations 1 (20 minutes and 5 seconds)
Chapter 18：ARM assembly arithmetic operations 2 (16 minutes and 36 seconds)
Chapter 19：ARM assembly arithmetic operations 3 (20 minutes and 14 seconds)
Chapter 20：ARM assembly arithmetic operations 4 (12 minutes and 17 seconds)
Chapter 21：ARM assembly memory operation 1 (20 minutes and 3 seconds)
Chapter 22：ARM assembly memory operation 2 (20 minutes and 8 seconds)
Chapter 23：Jump instructions and others1 (19 minutes and 48 seconds)
Chapter 24：Jump instructions and others 2 (19 minutes and 7 seconds)
Chapter 25：ARM assembly pseudo-instructions 1 (20 minutes and 6 seconds)
Chapter 26：ARM assembly directive 2 (20 minutes and 4 seconds)
Chapter 27：ARM assembly directive 3 (9 minutes and 22 seconds)
Chapter 28：ARM assembly directive 4 (23 minutes and 58 seconds)
Chapter 29：Hybrid Programming 1 (20 minutes and 9 seconds)
Chapter 30：Hybrid Programming 2 (12 minutes and 24 seconds)
Chapter 31：ARM hardware basics overview 1 (20 minutes and 4 seconds)
Chapter 32：ARM hardware basics overview 2 (20 minutes and 15 seconds)
Chapter 33：ARM hardware basics overview 3 (10 minutes and 21 seconds)
Chapter 34：ARM hardware basics-SIMD&NEON (19 minutes and 32 seconds)
Chapter 35：ARM hardware basics-Cache1 (20 minutes and 4 seconds)
Chapter 36：ARM hardware basics-Cache2 (11 minutes and 3 seconds)
Chapter 37：ARM hardware basics-MMU1 (20 minutes and 10 seconds)
Chapter 38：ARM hardware basics-MMU2 (20 minutes and 2 seconds)
Chapter 39：ARM hardware basics-MMU3 (6 minutes and 2 seconds)
Chapter 40：ARM exceptions and interrupts 1 (20 minutes and 2 seconds)
Chapter 41：ARM exceptions and interrupts 2 (21 minutes and 59 seconds)
Chapter 42：First bare board test 1 (20 minutes and 11 seconds)
Chapter 43：First bare board test 2 (13 minutes and 39 seconds)
Chapter 44：S5PV210 starting principle 1 (20 minutes and 3 seconds)
Chapter 45：S5PV210 starting principle 2 (11 minutes and 3 seconds)
Chapter 46：ARM hardware interface GPIO1 (20 minutes and 3 seconds)
Chapter 47：ARM hardware interface GPIO2 (20 minutes and 4 seconds)
Chapter 48：ARM hardware interface GPIO3 (6 minutes and 30 seconds)
Chapter 49：ARM hardware interface GPIO4 (22 minutes and 50 seconds)
Chapter 50：ARM hardware interface GPIO5 (27 minutes and 4 seconds)
Chapter 51：Determine development board resources 1 (20 minutes and 8 seconds)
Chapter 52：Determine development board resources 2 (20 minutes and 2 seconds)
Chapter 53：Determine development board resources 3 (20 minutes and 0 seconds)
Chapter 54：Determine development board resources 4 (4 minutes and 2 seconds)
Chapter 55：Driver development board resources 5 (20 minutes and 6 seconds)
Chapter 56：Driver development board resources 6 (20 minutes and 2 seconds)
Chapter 57：Driver development board resources 7 (17 minutes and 33 seconds)
Chapter 58：bootloader overview 1 (20 minutes and 3 seconds)
Chapter 59：bootloader overview 2 (20 minutes and 13 seconds)
Chapter 60：bootloader overview 3 (2 minutes and 26 seconds)
Chapter 61：bootloader overview 4 (20 minutes and 6 seconds)
Chapter 62：bootloader overview 5 (7 minutes and 37 seconds)
Chapter 63：C5 project builds Makefile1 (20 minutes and 8 seconds)
Chapter 64：C5 project builds Makefile2 (20 minutes and 10 seconds)
Chapter 65：C5 project builds Makefile3 (9 minutes and 59 seconds)
Chapter 66：Project build link script (20 minutes and 8 seconds)
Chapter 67：Project build link script (13 minutes and 53 seconds)
Chapter 68：Project construction C code lighting 1 (20 minutes and 6 seconds)
Chapter 69：Project construction C code lighting 2 (17 minutes and 5 seconds)
Chapter 70：Project construction C code lighting 3 (20 minutes and 5 seconds)
Chapter 71：Introduction to communication model 1 (20 minutes and 5 seconds)
Chapter 72：Introduction to communication model 2 (3 minutes and 22 seconds)
Chapter 73：Introduction to UART protocol 1 (20 minutes and 5 seconds)
Chapter 74：Introduction to UART protocol 2 (20 minutes and 3 seconds)
Chapter 75：UART protocol introduction 3 (2 minutes and 45 seconds)
Chapter 76：UART controller introduction 1 (20 minutes and 3 seconds)
Chapter 77：UART controller introduction 2 (15 minutes and 54 seconds)
Chapter 78：Send a character 1 through the serial port (20 minutes and 1 seconds)
Chapter 79：Send a character 2 through the serial port (20 minutes and 2 seconds)
Chapter 80：Send a character 3 through the serial port (20 minutes and 3 seconds)
Chapter 81：Send a character 4 through the serial port (15 minutes and 30 seconds)
Chapter 82：Send a string 1 through the serial port (20 minutes and 13 seconds)
Chapter 83：Send a string 2 through the serial port (2 minutes and 26 seconds)
Chapter 84：Interruption Introduction 1 (20 minutes and 3 seconds)
Chapter 85：Interruption Introduction 2 (20 minutes and 1 seconds)
Chapter 86：Interruption Introduction 3 (20 minutes and 14 seconds)
Chapter 87：Interruption Introduction 4 (15 minutes and 39 seconds)
Chapter 88：Interrupt initialization code 1 (20 minutes and 1 seconds)
Chapter 89：Interrupt initialization code 2 (20 minutes and 2 seconds)
Chapter 90：Interrupt initialization code 3 (13 minutes and 34 seconds)
Chapter 91：Interrupt process code 1 (18 minutes and 55 seconds)
Chapter 92：Interrupt process code 2 (20 minutes and 1 seconds)
Chapter 93：Interrupt process code 3 (17 minutes and 4 seconds)
Chapter 94：Introduction to IIC protocol 1 (20 minutes and 1 seconds)
Chapter 95：Introduction to IIC protocol 2 (20 minutes and 14 seconds)
Chapter 96：Introduction to IIC protocol 3 (20 minutes and 15 seconds)
Chapter 97：Introduction to IIC protocol 4 (4 minutes and 35 seconds)
Chapter 98：Introduction to IIC protocol 5 (20 minutes and 1 seconds)
Chapter 99：Introduction to IIC protocol 6 (27 seconds)
Chapter 100：watchdog introduction 1 (20 minutes and 3 seconds)
Chapter 101：watchdog introduction 2 (12 minutes and 52 seconds)
Chapter 102：Introduction to RTC (16 minutes and 47 seconds)
Chapter 103：Introduction to PWM 1 (20 minutes and 6 seconds)
Chapter 104：Introduction to PWM 2 (20 minutes and 5 seconds)
Chapter 105：Introduction to PWM 3 (2 minutes and 9 seconds)
Chapter 106：ADC introduction 1 (20 minutes and 5 seconds)
Chapter 107：ADC introduction 2 (7 minutes and 21 seconds)
Chapter 108：ARM hardware interface project introduction 1 (20 minutes and 1 seconds)
Chapter 109：ARM hardware interface project introduction 2 (20 minutes and 2 seconds)
Chapter 110：ARM hardware interface project introduction 3 (8 minutes and 55 seconds)
Chapter 111：ARM hardware interface project introduction 4 (20 minutes and 2 seconds)
Chapter 112：ARM hardware interface project introduction 5 (20 minutes and 9 seconds)
Chapter 113：ARM hardware interface project introduction 6 (20 minutes and 2 seconds)
Chapter 114：ARM hardware interface project introduction 7 (6 minutes and 8 seconds)
Chapter 115：Overall introduction to wifi audio course (12 minutes and 28 seconds)
Chapter 116：Firmware settings and network (34 minutes and 26 seconds)
Chapter 117：Software operation (20 minutes and 27 seconds)
Chapter 118：Sound card_driver (12 minutes and 39 seconds)
Chapter 119：Install Python and write Python scripts to control MP3 playback commands (15 minutes and 23 seconds)
Chapter 120：Write HTML5 web pages to call Python scripts to realize front-end control of MP3 playback (17 minutes and 12 seconds)
Chapter 121：Use mobile phones, computers, etc. to realize WIFI speakers to play music and MP3 (12 minutes and 49 seconds)
Chapter 122：Notes and FAQs (5 minutes and 47 seconds)
Chapter 123：Introduction to Internet of Things (6 minutes and 39 seconds)
Chapter 124：Introduction to Wireless Transmission Network (8 minutes and 18 seconds)
Chapter 125：A preliminary study on zigbee technology (10 minutes and 2 seconds)
Chapter 126：zigbee network structure (12 minutes and 15 seconds)
Chapter 127：IEEE802.15.4 communication layer 1 (8 minutes and 23 seconds)
Chapter 128：IEEE802.15.4 communication layer 2 (20 minutes and 33 seconds)
Chapter 129：zigbee network layer (8 minutes and 58 seconds)
Chapter 130：zigbee application layer 1 (16 minutes and 25 seconds)
Chapter 131：zigbee application layer 2 (14 minutes and 18 seconds)
Chapter 132：zigbee application layer 3 (13 minutes and 18 seconds)
Chapter 133：Introduction to zigbee smart home management system (5 minutes and 16 seconds)
Chapter 134：cc2530 structural frame (14 minutes and 20 seconds)
Chapter 135：Introduction to project software development environment (8 minutes and 39 seconds)
Chapter 136：Project basic programming experiment 1 (23 minutes and 13 seconds)
Chapter 137：Project basic programming experiment 2 (7 minutes and 37 seconds)
Chapter 138：Project Basic Programming Experiment 3 (22 minutes and 16 seconds)
Chapter 139：Project Basic Programming Experiment 4 (12 minutes and 44 seconds)
Chapter 140：Project simple communication programming (25 minutes and 39 seconds)
Chapter 141：zigbee smart home management system experiment (20 minutes and 38 seconds)
Chapter 142：zigbee smart home management system experiment (7 minutes and 58 seconds)
Chapter 143：zigbee smart home management system experiment (14 minutes and 59 seconds)
Chapter 144：Main access methods and wireless module classification of the Internet of Things (19 minutes and 50 seconds)
Chapter 145：The difference between micropower wireless module driver and microcontroller programming (20 minutes and 40 seconds)
Chapter 146：Several important concepts: dB, dBm and ppm (10 minutes and 6 seconds)
Chapter 147：Basic principles and uses of spectrum analyzers (22 minutes and 29 seconds)
Chapter 148：Hardware interface pattern of micropower wireless chips (14 minutes and 23 seconds)
Chapter 149：IF filter setting selection (top) (14 minutes and 45 seconds)
Chapter 150：Important peripheral components of micropower chips - transceiver switches (11 minutes and 20 seconds)
Chapter 151：Wireless communication data packet structure (13 minutes and 34 seconds)
Chapter 152：Register configuration of micropower chip (1) Carrier frequency setting (10 minutes and 16 seconds)
Chapter 153：Register configuration of micropower chip (2) IF filter setting (15 minutes and 46 seconds)
Chapter 154：Functional planning and flowchart design (17 minutes and 33 seconds)
Chapter 155：Read the wireless module manual. (12 minutes and 43 seconds)
Chapter 156：Hardware connection of remote control switch 1 (13 minutes and 15 seconds)
Chapter 157：IF filter setting selection (below) (17 minutes and 25 seconds)
Chapter 158：initializer module (15 minutes and 34 seconds)
Chapter 159：Send data program module (16 minutes and 17 seconds)
Chapter 160：receive data program module (24 minutes and 40 seconds)
Chapter 161：Overall program joint debugging and testing of remote control switches (11 minutes and 30 seconds)
Chapter 162：Foreword (camera usage situations) (5 minutes and 25 seconds)
Chapter 163：Some knowledge about cameras (9 minutes and 42 seconds)
Chapter 164：ov7670 introduction (16 minutes and 27 seconds)
Chapter 165：sccb bus (15 minutes and 2 seconds)
Chapter 166：ov7670 initialization (20 minutes and 29 seconds)
Chapter 167：Other camera configurations (18 minutes and 53 seconds)
Chapter 168：Hardware driver review (7 minutes and 51 seconds)
Chapter 169：menu design (13 minutes and 34 seconds)
Chapter 170：Hardware Configuration (9 minutes and 7 seconds)
Chapter 171：Data collection (21 minutes and 13 seconds)
Chapter 172：Take photos and albums (11 minutes and 16 seconds)
Chapter 173：complete camera (18 minutes and 9 seconds)
Chapter 174：Introduction to Maizi Smart Watch Structural Design Courses and Projects (9 minutes and 0 seconds)
Chapter 175：ID Appearance Analysis 1 (11 minutes and 20 seconds)
Chapter 176：Key component selection (15 minutes and 53 seconds)
Chapter 177：Product structure design (16 minutes and 48 seconds)
Chapter 178：Case design (14 minutes and 47 seconds)
Chapter 179：Movement design (17 minutes and 47 seconds)
Chapter 180：PCB structural element diagram design (11 minutes and 53 seconds)
Chapter 181：2D engineering drawing design and project difficulty analysis (18 minutes and 56 seconds)
Chapter 182：Preface (15 minutes and 27 seconds)
Chapter 183：LCD driver review (26 minutes and 15 seconds)
Chapter 184：Custom interface (31 minutes and 52 seconds)
Chapter 185：MQ2 smoke sensor (15 minutes and 45 seconds)
Chapter 186：Human body infrared module (10 minutes and 24 seconds)
Chapter 187：Temperature and humidity sensor (25 minutes and 57 seconds)
Chapter 188：Relays and stepper motors (14 minutes and 55 seconds)
Chapter 189：network (19 minutes and 54 seconds)
Chapter 190：Transfer Protocol (11 minutes and 50 seconds)
Chapter 191：data transmission (24 minutes and 29 seconds)
Chapter 192：debug (18 minutes and 19 seconds)
Chapter 193：log (7 minutes and 43 seconds)
Chapter 194：User management and factory settings (17 minutes and 57 seconds)
Chapter 195：introduce (7 minutes and 23 seconds)
Chapter 196：Introduction to design software (13 minutes and 20 seconds)
Chapter 197：An Introduction (13 minutes and 8 seconds)
Chapter 198：Main chip introduction (19 minutes and 50 seconds)
Chapter 199：Library design (28 minutes and 7 seconds)
Chapter 200：Quickly draw schematics (16 minutes and 28 seconds)
Chapter 201：Add package schematic diagram and import it into pcb (19 minutes and 2 seconds)
Chapter 202：Structural element import (6 minutes and 50 seconds)
Chapter 203：pcb settings (15 minutes and 17 seconds)
Chapter 204：pcb layout (23 minutes and 20 seconds)
Chapter 205：pcb wiring (17 minutes and 24 seconds)
Chapter 206：pcb wiring (24 minutes and 30 seconds)
Chapter 207：PCB optimization adjustment (14 minutes and 27 seconds)
Chapter 208：PCB board casting (10 minutes and 29 seconds)
Chapter 209：Hardware system and course introduction (14 minutes and 56 seconds)
Chapter 210：System-level design and functional decomposition (15 minutes and 39 seconds)
Chapter 211：Hands-on DIY VR glasses-obtaining raw materials (13 minutes and 33 seconds)
Chapter 212：DIY VR glasses – Assembling glasses (Part 1) (12 minutes and 26 seconds)
Chapter 213：Hands-on diy VR glasses - Assembling glasses (Part 2) (9 minutes and 30 seconds)
Chapter 214：I'm about to get a nosebleed - Adjusting glasses (13 minutes and 54 seconds)
Chapter 215：A must-have for experienced drivers - Introduction to Bluetooth controller (15 minutes and 19 seconds)
Chapter 216：Make a Bluetooth controller by hand – Purchase raw materials (16 minutes and 27 seconds)
Chapter 217：Make a Bluetooth controller - What is the difference between HID and SPP modules (Part 1) (10 minutes and 53 seconds)
Chapter 218：Make a Bluetooth controller - what is the difference between hid and spp modules (Part 2) (16 minutes and 41 seconds)
Chapter 219：Make a Bluetooth controller-mouse mode analysis (14 minutes and 57 seconds)
Chapter 220：Make a Bluetooth controller - keyboard mode analysis (15 minutes and 35 seconds)
Chapter 221：Make a Bluetooth controller - Analysis of controller modes (12 minutes and 22 seconds)
Chapter 222：Make a Bluetooth controller by hand - controller mode analysis (Part 2) (12 minutes and 19 seconds)
Chapter 223：Make a Bluetooth controller by hand - Solder the hardware (18 minutes and 10 seconds)
Chapter 224：Make a Bluetooth controller - stm32 project creation and peripheral initialization (Part 1) (18 minutes and 16 seconds)
Chapter 225：Make a Bluetooth controller - stm32 project creation and peripheral initialization (Part 2) (16 minutes and 54 seconds)
Chapter 226：Make a Bluetooth controller - handle joystick events (16 minutes and 39 seconds)
Chapter 227：Make a Bluetooth controller - implement mouse function (17 minutes and 14 seconds)
Chapter 228：Make a Bluetooth controller - multimedia buttons (Part 1) (15 minutes and 59 seconds)
Chapter 229：Make a Bluetooth controller - multimedia buttons (Part 2) (14 minutes and 19 seconds)
Chapter 230：Make a Bluetooth controller - keyboard mode, key combination processing (Part 1) (19 minutes and 56 seconds)
Chapter 231：Make a Bluetooth controller - keyboard mode, key combination processing (Part 2) (10 minutes and 32 seconds)
Chapter 232：Make a Bluetooth controller - implement a game controller (17 minutes and 39 seconds)
Chapter 233：Make a Bluetooth controller - function switching (16 minutes and 17 seconds)
Chapter 234：The handle and glasses are the magic weapon - joint test (9 minutes and 17 seconds)
Chapter 235：Course Summary (12 minutes and 38 seconds)
Chapter 236：before course (5 minutes and 23 seconds)
Chapter 237：AD9 development history and main functions introduction (7 minutes and 22 seconds)
Chapter 238：AD9 software installation (6 minutes and 43 seconds)
Chapter 239：First experience with AD9 (16 minutes and 48 seconds)
Chapter 240：AD9-Yuanti map parameter settings (19 minutes and 18 seconds)
Chapter 241：Drawing of a simple schematic diagram (14 minutes and 52 seconds)
Chapter 242：Hierarchical schematic design-1 (18 minutes and 16 seconds)
Chapter 243：Some knowledge points about schematic diagrams (21 minutes and 32 seconds)
Chapter 244：Preparation work for converting schematic diagram to PCB (15 minutes and 40 seconds)
Chapter 245：Familiar with PCB interface (15 minutes and 43 seconds)
Chapter 246：Rule settings and automatic layout (12 minutes and 13 seconds)
Chapter 247：PCB layout (19 minutes and 53 seconds)
Chapter 248：PCB self-made packaging library (15 minutes and 12 seconds)
Chapter 249：a case (18 minutes and 29 seconds)
You Might Like
Recommended Posts
- 【micropython】Bluetooth module has been added to ESP32
- In the latest build firmware of ESP32, the bluetooth module has been added, as shown in the figure:
-
dcexpert
MicroPython Open Source section
- MFC requires WINVER to be #defined to 0x0400 or greater
- MFC requires WINVER to be #defined to 0x0400 or greater
-
yyuan918
Embedded System
- Wake-on-LAN on the rtl8201fn chip
- [i=s] This post was last edited by Baobao Chen on 2016-5-31 17:11 [/i] I am working on the rtl8201fn network card chip recently. I have referred to many datashells related to rtl8201, but I have not f
-
陈宝宝
Linux and Android
- How strange!
- I have two LaunchPads, one is the old version and the other is the latest version. When I use the old version to program G2231, it says that the device cannot be found or the model is wrong, but when
-
wangfuchong
Microcontroller MCU
- Power Supply Design Tips
- Power supply design tip 1: Choose the right operating frequency for your power supply
-
lixiaohai8211
Power technology
- 97% off e-coins (can join in group)
- A total of 2,000 e-coins are planned to be transferred to other netizens on the forum, starting from 100 per person. You can pay RMB 97 for every 100 e-coins (you can use Alipay). The number of replie
-
cruelfox
Buy&Sell
Recommended Content
Web users are watching Change
- 【micropython】Bluetooth module has been added to ESP32
- MFC requires WINVER to be #defined to 0x0400 or greater
- Wake-on-LAN on the rtl8201fn chip
- How strange!
- Power Supply Design Tips
- 97% off e-coins (can join in group)
- Problems after remap of stm32 serial port 2!
- Popular horror stories
- Read the STM32 manual about flash issues
- IBM Power Architecture adds new innovation momentum, IBM microprocessor collaboration platform launched in China
- EEworld 2013 Week 15 (April 8-April 14) Power Technology Highlights
- Repair of a soldering station that short-circuits when powered on
- How to use interrupted delayed procedure calls in Streaming Minidriver
- Recruitment of electronic engineers
- /If you want to learn MCU well, read ``maybe it will be helpful to you
- Single chip microcomputer realizes T9 text input method circuit (source code + simulation)
- Analog Circuit Job Search Group (29945020) Please join as soon as possible
- On-site simulation
- MSP430x13x_MSP430F14x_MSP430F15x_MSP430F16x_Code_Examples
- PLC Video Materials
- Remembering Qu Yuan on Dragon Boat Festival
- 5.1 Selection <<< Introduction to positions in the world's top 500 companies in Shanghai>>>
- I have a weak question for help...
- Design of USB interface for embedded video image compression module
- How to solve the error when compiling ISE13.2?
- iFIX Introduction
- windows mobile ????????????????
- I would like to ask about the S parameter calculation of the low-pass filter
- ISE10.1 Warning
- Industrial control maintenance examples
Popular Components
Just Take a Look
Hot Downloads
- Safety Requirements Training Course for Small Household Appliances
- An Ultrafast Single Pulse (UFSP) Technique for Channel-Effective Mobility Measurement
- Design of UART IP core using Wishbone bus
- Homemade universal integrated circuit tester
- IH504851
- Graphics Library for embedded systems
- Wideband digital array beamforming based on fractional delay
- This is a tutorial that introduces spss10 in detail
- Use of BLOCKRAM
- Conquering Embedded Series 51
MoreHot Articles
京公网安备 11010802033920号