The failure rate (λ) and mean time between failures
(MTBF= 1/ λ) is calculated at max output power and
an operating ambient temperature (T
A
) of +40°C. CUI
Power Modules uses Telcordia SR-332 Issue 2 Method 1 to
calculate the mean steady-state failure rate and standard
deviation (σ).
Telcordia SR-332 Issue 2 also provides techniques to
estimate the upper confidence levels of failure rates based
on the mean and standard deviation.
Mean steady-state failure rate, λ Std. deviation, σ
421 n F ailures/h
60.9 nF ailures/h
the requirements of all applicable safety standards and
regulations for the final product.
Component power supplies for general use should comply
with the requirements in IEC/EN/UL 60950 1
Safety
of Information Technology Equipment.
Product related
standards, e.g. IEEE 802.3af
Power over Ethernet,
and
ETS 300132 2
Power interface at the input to telecom
equipment, operated by direct current (dc)
are based on
IEC/EN/UL 60950 1 with regards to safety.
CUI Power Modules DC/DC converters and DC/DC
regulators are UL 60950 1 recognized and certified in
accordance with EN 60950 1. The flammability rating for
all construction parts of the products meet requirements
for V 0 class material according to IEC 60695 11 10,
Fire
hazard testing, test flames
– 50 W horizontal and vertical
flame test methods.
Isolated DC/DC converters
Galvanic isolation between input and output is verified
in an electric strength test and the isolation voltage
(V
iso
) meets the voltage strength requirement for basic
insulation according to IEC/EN/UL 60950-1.
It is recommended to use a slow blow fuse at the input
of each DC/DC converter. If an input filter is used in the
circuit the fuse should be placed in front of the input filter.
In the rare event of a component problem that imposes a
short circuit on the input source, this fuse will provide the
following functions:
•
Isolate the fault from the input power source so as
not to affect the operation of other parts of
the system
•
Protect the distribution wiring from excessive
current and power loss thus preventing hazardous
overheating
The DC/DC converter output is considered as safety extra
low voltage (SELV) if one of the following conditions is
met:
•
The input source has double or reinforced
insulation from the AC mains according to IEC/EN/
UL 60950-1
•
The input source has basic or supplementary
insulation from the AC mains and the input
of the DC/DC converter is maximum 60
Vdc and connected to protective earth according to
IEC/EN/UL 60950-1
•
The input source has basic or supplementary
insulation from the AC mains and the DC/DC
converter output is connected to protective earth
according to IEC/EN/UL 60950-1
Non - isolated DC/DC regulators
The DC/DC regulator output is SELV if the input source
meets the requirements for SELV circuits according to IEC/
EN/UL 60950-1.
MTBF (mean value) for the NQB series = 2.9 Mh.
MTBF at 90% confidence level = 2.4 Mh
Compatibility with RoHS requirements
The products are compatible with the relevant clauses
and requirements of the RoHS directive 2011/65/EU and
have a maximum concentration value of 0.1% by weight
in homogeneous materials for lead, mercury, hexavalent
chromium, PBB and PBDE and of 0.01% by weight in
homogeneous materials for cadmium.
Exemptions in the RoHS directive utilized in CUI
Power Modules products are found in the Statement of
Compliance document.
Safety Specification
Reliability
CUI Power Modules DC/DC converters and DC/DC
regulators are designed in accordance with the safety
standards IEC 60950 1, EN 60950 1 and UL 60950 1
Safety of Information Technology Equipment.
IEC/EN/UL 60950 1 contains requirements to prevent
injury or damage due to the following hazards:
•
Electrical shock
•
Energy hazards
•
Fire
•
Mechanical and heat hazards
•
Radiation hazards
•
Chemical hazards
On-board DC/DC converters and DC/DC regulators are
defined as component power supplies. As components
they cannot fully comply with the provisions of any
safety requirements without “conditions of acceptability”.
Clearance between conductors and between conductive
parts of the component power supply and conductors on
the board in the final product must meet the applicable
safety requirements. Certain conditions of acceptability
apply for component power supplies with limited stand-off
(see Mechanical Information for further information). It is
the responsibility of the installer to ensure that the final
product housing these components complies with
cui.com
For more information, please visit the
product page.
CUI Inc
│
SERIES:
NQB-N
│
DESCRIPTION:
FULLY REGULATED ADVANCED BUS CONVERTERS
date
11/07/2014
│
page
4 of 30
Absolute Maximum Ratings
parameter
operating temperature (T
P1
)
storage temperature (T
S
)
input voltage (V
I
)
isolation voltage (V
iso
)
input voltage transient (V
tr
)
remote control pin voltage (V
RC
)
input to output test voltage, see note 1
according to ETSI EN 300 132-2 and Telcordia GR-
1089-CORE
see operating information section
-0.3
conditions/description
see thermal consideration section
min
-40
-55
-0.5
typ
max
+125
+125
+80
+65*
2250
+100
+80*
18
units
°C
°C
V
Vdc
V
V
Stress in excess of Absolute Maximum Ratings may cause permanent damage. Absolute Maximum Ratings, sometimes referred to as no destruction limits, are normally tested with one
parameter at a time exceeding the limits of Output data or Electrical Characteristics. If exposed to stress above these limits, function and performance may degrade in an unspecified
manner.
Note
1: Isolation voltage (input/output to base-plate) max 750 Vdc.
1. The basic principle of current detection resistor:According to Ohm's law, when the measured current flows through the resistor, the voltage across the resistor is proportional to the current. When ...
Table of contents
1.tl_led_flash example
1.1Case Function
1.2Operation Instructions
1.3Key Code
2.tl_key_test case
2.1Case Function
2.2Operation Instructions
2.3Key Code
3.tl_uart_rw example
3.1Case F...
Introduction to Machine Learning : https://training.eeworld.com.cn/course/4461The goal of machine learning is to program computers to solve given problems using sample data or past experience. There h...
Hello everyone: I want to DIY a flying machine, powered by lithium batteries, and I am stuck in choosing a motor. I searched on Baidu and found that they all talk about the basic principles of motors,...
The air around us is a sea of radio emissions from tens of kHz to tens of GHz, with transmitter power levels ranging from milliwatts to megawatts for the largest “long wave” broadcasters. We’re probab...
With the continuous improvement of microcontroller performance and the reduction of costs, microcontrollers have been widely used in various fields. Especially in the control and processing of signals...
The multimeter can detect LED using the diode mode LED is also a diode and has the same unidirectional conduction characteristic, which only allows current to flow from the positive pole to the n...[Details]
Recently, u-blox has released a highly integrated GNSS (Global Navigation Satellite System) technology platform u-blox M10, which is completely designed by u-blox and is suitable for ultra-low power ...[Details]
The main development environment of STM8 is IAR. Here are some common shortcut keys of IAR: The shortcut key for IAR global search is , and the pop-up interface is as follows: IAR Find Options ...[Details]
The lithium battery company I’m going to talk about today is not yet one of the top 10 companies in power battery installations, but it is indeed a lithium battery giant and is likely to have a great...[Details]
1. The SPI module of structure 5744 supports full-duplex three-wire synchronous transmission and can run in master or slave mode. It contains FIFO send and receive buffers with a depth of 5 respectiv...[Details]
Last October, Intel announced that it would sell its NAND flash memory business to SK Hynix for $9 billion. The deal was approved by the United States in March and the European Union a few days ago. ...[Details]
President Joe Biden’s blueprint for the U.S. semiconductor industry marks an ambitious effort to develop industrial policy for key sectors of the economy, but the strategy also requires more funding ...[Details]
Currently, Asian countries such as China and South Korea occupy a major share of the power battery market. However, with the rapid development of the European new energy vehicle market and the substa...[Details]
Question: How to call a DLL from LabVIEW
Solution: To call a dynamic link library (DLL) from LabVIEW, you need to first determine what type of DLL it is. There are basically two types of DLLs to c...[Details]
Recently, CATL signed a battery supply agreement with the German company TrailerDynamics, to develop and provide the latter with a 300kWh lithium iron phosphate battery pack for its first product, th...[Details]
Introduction to Data Block (DB)
(1) Introduction to Data Block (DB)
Data blocks are used to store user data and program intermediate variables. When a new data block is created, the defau...[Details]
STC12C5A60S2 automatic download program When we use the STC series microcontroller to develop projects, the most annoying thing is that every time you click Download, you have to turn off the power ...[Details]
1. Steps to write ts driver (beginners can just take a look at it, the content is a bit confusing)
1. Copy the header file;
2. Write entry and exit functions
3. All...[Details]
Analogue and Mixed Signal
京公网安备 11010802033920号
EEWORLD
